> Authentication host-mode multi-domain

Yes, it’s mandatory, it will allow you to have one Mac address into the DATA 
domain and one Mac address into the VOICE domain.

Use case: Computer plugged on the back of the phone.

The voice domain is necessary if you want to use the voice capabilities of the 
Cisco switch. The Cisco-AVPair = "device-traffic-class=voice” instruction from 
PF to the switch, will tell the switch to put that Mac address into the voice 
lan configured on the port.

Thanks,

Ludovic Zammit
[email protected] <mailto:[email protected]> ::  +1.514.447.4918 (x145) ::  
www.inverse.ca <https://www.inverse.ca/>
Inverse inc. :: Leaders behind SOGo (http://www.sogo.nu <http://www.sogo.nu/>) 
and PacketFence (http://packetfence.org <http://packetfence.org/>)







> On Mar 23, 2021, at 12:57 PM, NITISH AGGARWAL <[email protected]> wrote:
> 
> Ok..thank you Thomas and Ludovic.
> 
> Just one thing, is this command "authentication host-mode " is mandatory???
> 
> I have configured one switch port without it and tried to figure this out and 
> till now everything is working fine. Is this command mandatory bcoz sometimes 
> while I am using authentication host-mode as multi-host, instead of 
> authentication my pc it got struck at my ip phone and resulted in Port 
> authentication failure and I have to shut unshut that port to make it working.
> 
> 
> I also want to bring one thing to your notice that as I saw my ip phone Mac 
> address under nodes, I saw connection type as blank, while for PCs it is 
> ethernet eap, is this the issue. There should be some connection type maybe 
> non ethernet eap for ip phone but it is blank.
> 
> On Tue, Mar 23, 2021, 21:58 Ludovic Zammit via PacketFence-users 
> <[email protected] 
> <mailto:[email protected]>> wrote:
> Hello,
> 
> Tomas points are good and he is right.
> 
> In order for PF to send out the specific radius reply for a phone, you will 
> need to make you check:
> 
> - SNMP correctly configure on the switch and/or PF switch Configuration as 
> well
> - Check the VOIP support for your switch module in PF
> - Make sure your phone has LLDP / CDP enable for auto-registration
> - Check the radius reply for that Mac address it should look like this: 
> “Cisco-AVPair = "device-traffic-class=voice"”
> - Make sure the VOIP box is checked under the Mac address
> 
> Thanks,
> 
> Ludovic Zammit
> [email protected] <mailto:[email protected]> ::  +1.514.447.4918 (x145) ::  
> www.inverse.ca <https://www.inverse.ca/>
> Inverse inc. :: Leaders behind SOGo (http://www.sogo.nu 
> <http://www.sogo.nu/>) and PacketFence (http://packetfence.org 
> <http://packetfence.org/>)
> 
> 
> 
> 
> 
> 
> 
>> On Mar 22, 2021, at 2:00 PM, Thomas Michel via PacketFence-users 
>> <[email protected] 
>> <mailto:[email protected]>> wrote:
>> 
>> Hi,
>> 
>> 
>> 
>> authentication host-mode multi-host means that if a single device is 
>> authenticated all devices can access the network. So in your configuration 
>> it works as expected.
>> 
>> Are you using Cisco phones? If not, try to use authentication host-mode 
>> multi-auth, which means each new mac address needs to authenticate itself. 
>> Otherwise you can use multi-domain mode.
>> 
>> Also, you might want to remove the switchport port-security command, they 
>> are not needed in a dotx environment.
>> 
>> If using cisco phones make sure CDP is enabled on the switch.
>> 
>> Usefull troubleshooting command is "debug dot1x events" to see what happens 
>> when you connect a device and show authetication session interface 
>> <interface> detail to see all dot1x configuration and authentications on the 
>> switchport.
>> 
>> "show cdp neighbors" will show you if a cisco phone is discovered.
>> 
>> Regards,
>> 
>> Tom.
>> 
>> Am 22.03.2021 um 18:14 schrieb NITISH AGGARWAL via PacketFence-users:
>>> Only my pc got authenticated via dot1x and no authentication for phone . 
>>> Although my phone keeps on working no matter it is not authenticated.
>>> 
>>> But if I used "authentication host mode as multi-domain" instead of 
>>> multi-host all stops because my phone not gets authenticated then and 
>>> struck in provisioning.
>>> 
>>> On Mon, Mar 22, 2021, 22:32 Ludovic Zammit <[email protected] 
>>> <mailto:[email protected]>> wrote:
>>> Connect both of them and show me the result of this command:
>>> 
>>> show authentication session int YOUR_INTERFACE detail
>>> 
>>> Thanks,
>>> Ludovic Zammit
>>> [email protected] <mailto:[email protected]> ::  +1.514.447.4918 (x145) 
>>> ::  www.inverse.ca <https://www.inverse.ca/>
>>> Inverse inc. :: Leaders behind SOGo (http://www.sogo.nu 
>>> <http://www.sogo.nu/>) and PacketFence (http://packetfence.org 
>>> <http://packetfence.org/>)
>>> 
>>> 
>>> 
>>> 
>>> 
>>> 
>>> 
>>>> On Mar 22, 2021, at 12:55 PM, NITISH AGGARWAL <[email protected] 
>>>> <mailto:[email protected]>> wrote:
>>>> 
>>>> Voice vlan 100 and access vlan 10
>>>> 
>>>> On Mon, Mar 22, 2021, 22:23 Ludovic Zammit <[email protected] 
>>>> <mailto:[email protected]>> wrote:
>>>> What’s your voice VLAN id ?
>>>> 
>>>> Thanks,
>>>> Ludovic Zammit
>>>> [email protected] <mailto:[email protected]> ::  +1.514.447.4918 (x145) 
>>>> ::  www.inverse.ca <https://www.inverse.ca/>
>>>> Inverse inc. :: Leaders behind SOGo (http://www.sogo.nu 
>>>> <http://www.sogo.nu/>) and PacketFence (http://packetfence.org 
>>>> <http://packetfence.org/>)
>>>> 
>>>> 
>>>> 
>>>> 
>>>> 
>>>> 
>>>> 
>>>>> On Mar 22, 2021, at 12:13 PM, NITISH AGGARWAL <[email protected] 
>>>>> <mailto:[email protected]>> wrote:
>>>>> 
>>>>> switchport mode access
>>>>> Switchport access vlan 10
>>>>> switchport voice vlan 100
>>>>> switchport port-security mac-address sticky 0200.000x.xxxx
>>>>> switchport port-security maximum 2
>>>>> authentication host-mode multi-host
>>>>> authentication order dot1x mab
>>>>> authentication priority dot1x mab
>>>>> authentication port-control auto
>>>>> authentication periodic
>>>>> mab
>>>>> no snmp trap link-status
>>>>> dot1x pae authenticator
>>>>> dot1x timeout quiet-period 2
>>>>> dot1x timeout tx-period 3
>>>>> 
>>>>> On Mon, Mar 22, 2021, 20:12 Ludovic Zammit <[email protected] 
>>>>> <mailto:[email protected]>> wrote:
>>>>> Hello,
>>>>> 
>>>>> Show me the interface configuration that you have on your switch where 
>>>>> you plug your phone.
>>>>> 
>>>>> Thanks,
>>>>> Ludovic Zammit
>>>>> [email protected] <mailto:[email protected]> ::  +1.514.447.4918 (x145) 
>>>>> ::  www.inverse.ca <https://www.inverse.ca/>
>>>>> Inverse inc. :: Leaders behind SOGo (http://www.sogo.nu 
>>>>> <http://www.sogo.nu/>) and PacketFence (http://packetfence.org 
>>>>> <http://packetfence.org/>)
>>>>> 
>>>>> 
>>>>> 
>>>>> 
>>>>> 
>>>>> 
>>>>> 
>>>>>> On Mar 18, 2021, at 8:27 AM, NITISH AGGARWAL via PacketFence-users 
>>>>>> <[email protected] 
>>>>>> <mailto:[email protected]>> wrote:
>>>>>> 
>>>>>> Hi,
>>>>>> 
>>>>>> I have setup PacketFence as per guide. Dot1x is enabled and working but 
>>>>>> I am not able to use MAB. Due to which my ip phones are not get 
>>>>>> authenticated. 
>>>>>> 
>>>>>> In switch (cisco 2960) I was using authentication host-mode as 
>>>>>> multi-domain and MAB is enable. But since it was not authenticating I am 
>>>>>> using host-mode as multi-host. Now my system and phone is working but it 
>>>>>> is not authenticating my ip phone which is causing problem sometimes. I 
>>>>>> am not able to resolve the issue please suggest what needs to be done
>>>>>> _______________________________________________
>>>>>> PacketFence-users mailing list
>>>>>> [email protected] 
>>>>>> <mailto:[email protected]>
>>>>>> https://lists.sourceforge.net/lists/listinfo/packetfence-users 
>>>>>> <https://lists.sourceforge.net/lists/listinfo/packetfence-users>
>>>>> 
>>>> 
>>> 
>>> 
>>> 
>>> 
>>> _______________________________________________
>>> PacketFence-users mailing list
>>> [email protected] 
>>> <mailto:[email protected]>
>>> https://lists.sourceforge.net/lists/listinfo/packetfence-users 
>>> <https://lists.sourceforge.net/lists/listinfo/packetfence-users>
>> <OpenPGP_0x8049779A866B418C.asc>_______________________________________________
>> PacketFence-users mailing list
>> [email protected] 
>> <mailto:[email protected]>
>> https://lists.sourceforge.net/lists/listinfo/packetfence-users 
>> <https://lists.sourceforge.net/lists/listinfo/packetfence-users>
> 
> _______________________________________________
> PacketFence-users mailing list
> [email protected] 
> <mailto:[email protected]>
> https://lists.sourceforge.net/lists/listinfo/packetfence-users 
> <https://lists.sourceforge.net/lists/listinfo/packetfence-users>

_______________________________________________
PacketFence-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/packetfence-users

Reply via email to