Tools->Start Trace ..do something.. Tools->Stop Trace In 3.8 I think it was buried under tools->python shell.
David E DeMarle Kitware, Inc. R&D Engineer 21 Corporate Drive Clifton Park, NY 12065-8662 Phone: 518-881-4909 On Fri, Mar 23, 2012 at 4:38 PM, Lorenzo <lovecraf...@gmail.com> wrote: > Sorry David, what do you mean with "record a trace"? > > > Il giorno 23/mar/2012, alle ore 19:03, David E DeMarle ha scritto: > >> You can also record either a trace or a state file in paraview where >> you load a couple of files, then edit that recorded file in a text >> editor and add in the additional files. Of the two, the trace file, >> being a python script, is easier to edit and programmatically extend. >> >> David E DeMarle >> Kitware, Inc. >> R&D Engineer >> 21 Corporate Drive >> Clifton Park, NY 12065-8662 >> Phone: 518-881-4909 >> >> >> >> On Fri, Mar 23, 2012 at 1:34 PM, Lorenzo <lovecraf...@gmail.com> wrote: >>> Thank you Frank; >>> I know about this, I just would like to find a way to load everything as a >>> vtk as well… >>> >>> >>> Il giorno 23/mar/2012, alle ore 17:47, Albina, Frank ha scritto: >>> >>>> Hi Lorenzo! >>>> >>>> Maybe you'd better off with reading the OpenFOAM solution with the >>>> built-in OpenFOAM reader. Just create in your case directory an empty >>>> OF.foam file and you can start reading the solution by opening this file >>>> from the GUI. >>>> >>>> Hope this helps. >>>> >>>> Frank. >>>> >>>> -----Original Message----- >>>> From: paraview-boun...@paraview.org [mailto:paraview-boun...@paraview.org] >>>> On Behalf Of Lorenzo >>>> Sent: Freitag, 23. März 2012 17:11 >>>> To: paraview@paraview.org >>>> Subject: Re: [Paraview] Load many VTK from different folders at once >>>> >>>> I was thinking: maybe there's a way to create a text files (or something >>>> in another format) which contains the paths to the vtk files I need to >>>> open and this file could be submitted to paraview to automate the whole >>>> process of opening every each one of the vtk files... >>>> >>>> What do you think? >>>> >>>> Thank you! >>>> >>>> >>>> Il giorno 22/mar/2012, alle ore 20:26, lore ha scritto: >>>> >>>>> Hi all, >>>>> I am using openFoam and when I run foamToVTK I get many vtk files every >>>>> each >>>>> one of which is contained in a different folder. If my geometry is made >>>>> up by >>>>> many .stl different files then I get the same number of folders. This is >>>>> quite >>>>> annoying when I need to load up the whole geometry because I need to enter >>>>> the first folder and load the first .vtk, then go to file-->open-->enter >>>>> the >>>>> second folder and load the second .vtk and so on until I loaded all the >>>>> files I >>>>> need. As you may understand this is quite time consuming... Any way to do >>>>> the >>>>> whole process at once? >>>>> >>>>> I think the best way would be to link together all of these vtk files >>>>> into one >>>>> single file (even of a different format) using a script (sh, python, >>>>> bash...??). >>>>> >>>>> This is something you may do with the .stl files, if they are in binary >>>>> format >>>>> you may concatenate the content of each one of them into a single >>>>> different >>>>> file and then load just that one to have everything at once... >>>>> >>>>> What do you think? >>>>> >>>>> Thank you! >>>>> >>>>> _______________________________________________ >>>>> Powered by www.kitware.com >>>>> >>>>> Visit other Kitware open-source projects at >>>>> http://www.kitware.com/opensource/opensource.html >>>>> >>>>> Please keep messages on-topic and check the ParaView Wiki at: >>>>> http://paraview.org/Wiki/ParaView >>>>> >>>>> Follow this link to subscribe/unsubscribe: >>>>> http://www.paraview.org/mailman/listinfo/paraview >>>> >>>> _______________________________________________ >>>> Powered by www.kitware.com >>>> >>>> Visit other Kitware open-source projects at >>>> http://www.kitware.com/opensource/opensource.html >>>> >>>> Please keep messages on-topic and check the ParaView Wiki at: >>>> http://paraview.org/Wiki/ParaView >>>> >>>> Follow this link to subscribe/unsubscribe: >>>> http://www.paraview.org/mailman/listinfo/paraview >>> >>> _______________________________________________ >>> Powered by www.kitware.com >>> >>> Visit other Kitware open-source projects at >>> http://www.kitware.com/opensource/opensource.html >>> >>> Please keep messages on-topic and check the ParaView Wiki at: >>> http://paraview.org/Wiki/ParaView >>> >>> Follow this link to subscribe/unsubscribe: >>> http://www.paraview.org/mailman/listinfo/paraview > _______________________________________________ Powered by www.kitware.com Visit other Kitware open-source projects at http://www.kitware.com/opensource/opensource.html Please keep messages on-topic and check the ParaView Wiki at: http://paraview.org/Wiki/ParaView Follow this link to subscribe/unsubscribe: http://www.paraview.org/mailman/listinfo/paraview