Hi Faraz, I can look into your system if you can provide me ssh access. I don't promise to fix your issue but have experience with Raspberry Pis and Paraview builds. And I don't need money, I'll do it out of curiosity and in free time :)
On Tue, Feb 14, 2017 at 4:55 PM, Faraz Hussain <i...@feacluster.com> wrote: > Unfortunately, I am not having much luck getting Paraview to build. I keep > trying to configure (c), but the generate (g) option does not come. I am > wondering if someone would be willing to poke around in my system . I can > pay some nominal amount for your time. However , since this is mainly for > education my budget is limited ( ~$100 ). > > > Quoting Sebastien Jourdain <sebastien.jourd...@kitware.com>: > > You need to hit [c](configure) several time before getting the generate. >> >> On Fri, Feb 10, 2017 at 2:33 PM, Scott Wittenburg < >> scott.wittenb...@kitware.com> wrote: >> >> Also for paraviewweb, don't forget: >>> >>> PARAVIEW_ENABLE_PYTHON=ON >>> >>> Cheers, >>> >>> Scott >>> >>> On Fri, Feb 10, 2017 at 2:31 PM, Scott Wittenburg < >>> scott.wittenb...@kitware.com> wrote: >>> >>> I would think you'd want to build with: >>>> >>>> PARAVIEW_BUILD_QT_GUI=OFF >>>> >>>> Hope this helps, >>>> >>>> Scott >>>> >>>> On Fri, Feb 10, 2017 at 2:25 PM, Faraz Hussain <i...@feacluster.com> >>>> wrote: >>>> >>>> Thanks for your help in installing Paraview on a raspberry pi. I >>>>> followed the steps in: >>>>> >>>>> http://www.paraview.org/Wiki/ParaView:Build_And_Install >>>>> >>>>> However, when I configure ccmake it says QT is needed. I could not >>>>> figure out if I can ignore that. The "generate" command did not come >>>>> up. >>>>> >>>>> On a side note, it took me a while to find ccmake. I thought it was >>>>> installed with cmake, but seems I had to install it separately using >>>>> "sudo >>>>> apt-get install cmake-curses-gui" . Perhaps the instructions should be >>>>> updated to reflect this to avoid confusion. >>>>> >>>>> >>>>> Quoting Sebastien Jourdain <sebastien.jourd...@kitware.com>: >>>>> >>>>> Wow, >>>>> >>>>>> >>>>>> I'm not an expert on raspberry pi but it should be possible. >>>>>> BUT, (and it is a big but) you need some graphics capability for >>>>>> ParaView >>>>>> or good CPUs if you don't have a GPU. >>>>>> Or the rendering will be really slow. >>>>>> >>>>>> The quicker test you can do, is to build ParaView (without Qt) and try >>>>>> to >>>>>> run Visualizer with that ParaView in the command line to see what >>>>>> performance you are getting. If that's reasonable, then all the >>>>>> network >>>>>> setup should be "trivial". >>>>>> >>>>>> ParaView: http://www.paraview.org/Wiki/ParaView:Build_And_Install >>>>>> Visualizer: https://kitware.github.io/visualizer/ >>>>>> >>>>>> Good luck, >>>>>> >>>>>> Seb >>>>>> >>>>>> On Wed, Feb 8, 2017 at 8:15 AM, Faraz Hussain <i...@feacluster.com> >>>>>> wrote: >>>>>> >>>>>> I want to be able to manipulate vtk file on my raspberry pi via a web >>>>>> >>>>>>> browser anywhere in the world. I believe I need to install >>>>>>> paraviewweb >>>>>>> and >>>>>>> do some reconfiguration of apache and the virtual hosts? >>>>>>> Unfortunately, I >>>>>>> am not a guru of Linux. So before I attempt it all, is it even >>>>>>> possible to >>>>>>> do this on a raspberry pi? I am using raspian . >>>>>>> >>>>>>> _______________________________________________ >>>>>>> Powered by www.kitware.com >>>>>>> >>>>>>> Visit other Kitware open-source projects at >>>>>>> http://www.kitware.com/opensou >>>>>>> rce/opensource.html >>>>>>> >>>>>>> Please keep messages on-topic and check the ParaView Wiki at: >>>>>>> http://paraview.org/Wiki/ParaView >>>>>>> >>>>>>> Search the list archives at: http://markmail.org/search/?q=ParaView >>>>>>> >>>>>>> Follow this link to subscribe/unsubscribe: >>>>>>> http://public.kitware.com/mailman/listinfo/paraview >>>>>>> >>>>>>> >>>>>>> >>>>> >>>>> _______________________________________________ >>>>> Powered by www.kitware.com >>>>> >>>>> Visit other Kitware open-source projects at >>>>> http://www.kitware.com/opensource/opensource.html >>>>> >>>>> Please keep messages on-topic and check the ParaView Wiki at: >>>>> http://paraview.org/Wiki/ParaView >>>>> >>>>> Search the list archives at: http://markmail.org/search/?q=ParaView >>>>> >>>>> Follow this link to subscribe/unsubscribe: >>>>> http://public.kitware.com/mailman/listinfo/paraview >>>>> >>>>> >>>> >>>> >>> > > > _______________________________________________ > Powered by www.kitware.com > > Visit other Kitware open-source projects at http://www.kitware.com/opensou > rce/opensource.html > > Please keep messages on-topic and check the ParaView Wiki at: > http://paraview.org/Wiki/ParaView > > Search the list archives at: http://markmail.org/search/?q=ParaView > > Follow this link to subscribe/unsubscribe: > http://public.kitware.com/mailman/listinfo/paraview > -- Faiz Abidi | Master's Student at Virginia Tech | www.faizabidi.com | +1-540-998-6636
_______________________________________________ Powered by www.kitware.com Visit other Kitware open-source projects at http://www.kitware.com/opensource/opensource.html Please keep messages on-topic and check the ParaView Wiki at: http://paraview.org/Wiki/ParaView Search the list archives at: http://markmail.org/search/?q=ParaView Follow this link to subscribe/unsubscribe: http://public.kitware.com/mailman/listinfo/paraview