A small correction:
apparently device 0 does not work no matter what, but /dev/dv1394/0 works
sometimes but only with black output.
Here's the relevant output from the Pd:
Open example video/00.SimpleVideo.pd
Shell (from which Pd was started): /dev/video0: No such file or directory
(i guess this is expected since ADVC-100 is dv1394 device)
Click on device 0 and driver 1:
No feedback
Start rendering:
Pd window: Direct Rendering enabled!
GEM: Start rendering
[pix_videoNEW]: starting transfer
DV4L: closed
GL: invalid enumerant
Shell: /dev/ieee1394/dv/host0/NTSC/in: Is a directory
Stop rendering:
Pd window: GEM: Stop rendering
Make message device /dev/dv1394/0, click on it:
Shell: get capabilities: Invalid argument
get capabilities: Invalid argument (yes, twice)
Pd window: [pix_videoNEW]: device-err: 0
Click on mode NTSC and then driver 1:
Pd window: DV4L: DV decoding quality 5
At this point when I enable the rendering I consistently get (unlike
before):
Pd window: Direct Rendering enabled!
GEM: Start rendering
[pix_videoNEW]: starting transfer
DV4L: closed
GL: invalid enumerant
Shell: /dev/dv1394/0: Device or resource busy
/dev/raw1394, and /dev/video1394/0 or /dev/video yields invalid argument for
capabilities and does not work.
Again, I would greatly appreciate your insight in this matter before I
resort to switching to a different distro/version.
Many thanks!
Best wishes,
Ico
On 12/27/06, Ivica Ico Bukvic <[EMAIL PROTECTED]> wrote:
Aaaargh, accidentally pressed "send" button...
The only thing left to report is that /dev tree has
dv1394/0
video/0
video -> video/0 symlink
raw1394
Modules loaded are the usual bunch ohci1394 ieee 1394 dv1394 raw1394. I
also tried manually modprobing video1394 with no effect.
/dev/ieee1394 tree is missing but recreating it manually
(/dev/ieee1394/.../in and .../out simply makes "device0" also work with the
same effect as described below.
0.90 gem is worse since it does not allow non-standard choice of devices
but it does not appear to be any better off than the 0.91.
Obviously this suggests that there is something fishy with Edgy, but the
question is what?
Any help is most appreciated!
Best wishes,
Ico
On 12/27/06, Ivica Ico Bukvic <[EMAIL PROTECTED]> wrote:
>
> Hi all,
>
> Here I am 6 months later trying to upgrade my laptop and a new issue has
> cropped up with my video capture in Gem.
>
> System: Ubuntu 6.10 (edgy) i386 using udev
> Graphics: ATI 9600 running fglrx
> Kernel: 2.6.18-rt7
> Video capture: el-cheapo camcorder run through ADVC-100 firewire device
>
> When running Kino, the camera gets captured just fine and everything
> "just works" as expected. However, in Gem (tried 0.90, CVS from November
> and another one from today's snapshot), I need to send following messages
> for Gem capture to work at all:
>
> device /dev/dv1394/0
> mode NTSC
> driver 1
>
> This starts capture reporting DV capture quality at 5, but the captured
> stuff is black. The only proof that things are getting captured comes from
> disconnecting the feed in the middle of the capture by pulling the video
> cable that connects camcorder with the ADVC-100 and then one can notice
> change in the color and/or momentary flicker of the captured area.
>
>
>
_______________________________________________
PD-list@iem.at mailing list
UNSUBSCRIBE and account-management ->
http://lists.puredata.info/listinfo/pd-list
