And yet is not the P99SE forum. This is the Protel EDA forum, and it was designed to provide an environment for all users of Protel EDA software, including but not exclusive to P99SE and all versions back and forward of that version. For instance, I've been a subscriber to this listgroup since the mid 1990s, when I was just considering movement from my Protel Autorax DOS EDA program into P98 and have seen question put to the group from people using easytrax...
One might benefit by occasionally going back to the site where they signed up for this group and re-reading the purpose and rules for the forum. >-----Original Message----- >From: [EMAIL PROTECTED] >[mailto:[EMAIL PROTECTED] On Behalf Of Pearce, Daniel >Sent: Friday, August 10, 2007 10:44 AM >To: Protel EDA Discussion List >Subject: Re: [PEDA] lost solid copper in 99se > >I'd have to second that re. this being the "99SE Forum" > >Our main reason for sticking to 99SE are: > >1. Resistance to the learning curve for AD's very different paradigm. > Especially important because I only do a few board designs/year, > but they're very "manual", i.e. high-power switching supplies > & amplifiers not well suited to autorouters & simple design rules. > >2. P99SE is still the #1 or #2 preferred tool at *all* of the > Contract Mfr's that we currently use in the Far East. > >3. Some of those Mfr's also do their own PCB design which are > perfectly adequate for DSP boards, etc. It helps us a lot > if we can use the same tool to open their designs for > review & testing. > >So, I hope this list can stay alive for a while longer... > >Dan > > > >> -----Original Message----- >> From: [EMAIL PROTECTED] >> [mailto:[EMAIL PROTECTED] On Behalf Of Stephen Casey >> Sent: Friday, August 10, 2007 9:43 AM >> To: [EMAIL PROTECTED]; 'Protel EDA Discussion List' >> Subject: Re: [PEDA] lost solid copper in 99se >> >> >> Hello, >> >> Most people have switched to Altium Designer now, and use the Altium >> provided forum. This list seems to be the remnants of people still >> using 99SE. >> >> Steve. >> >> -----Original Message----- >> From: [EMAIL PROTECTED] >> [mailto:[EMAIL PROTECTED] On Behalf Of Robert Gillatt >> Sent: 10 August 2007 14:02 >> To: 'Protel EDA Discussion List' >> Subject: Re: [PEDA] lost solid copper in 99se >> >> Hi, >> Is the volume of postings very small or am I out of the loop >somehow? >> I first subscribed in 2000 when I started working with >Protel and the >> volume was so great that I had to switch it off most of the time. I >> rejoined about three weeks ago when we eventually got hold of a DXP >> licence but I have only seen 3 posts so far. >> I have checked my spam filters and PEDA settings but something just >> doesn't feel right. >> Thanks >> >> Rob G >> >> -----Original Message----- >> From: [EMAIL PROTECTED] >> [mailto:[EMAIL PROTECTED] On Behalf Of Kulajew, Waldemar >> Sent: 10 August 2007 12:47 >> To: Protel EDA Discussion List >> Subject: Re: [PEDA] lost solid copper in 99se >> >> >> Yes, you have. >> Or you should make sure the polys are drawn as hatched in >> AD2004. For solid >> copper was a new feature in AD2004 and unknown in 99SE. >> >> >> Regards >> >> Waldemar >> _______________________________________________________________ >> PS: guess you will have a more friendly welcome here if you >> let us know who you realy are... testingfan >> ______________________________________________________________ >> >> >> > -----Original Message----- >> > From: [EMAIL PROTECTED] >> > [mailto:[EMAIL PROTECTED] On Behalf Of tastingfan >> > tastingfan >> > Sent: Friday, August 10, 2007 11:47 AM >> > To: [email protected] >> > Subject: [PEDA] lost solid copper in 99se >> > >> > Hello, >> > >> > I have encountered a problem. The solid copper in DXP2004 >> > is lost when this PCB file is opened with 99se. Do I have to >> > redraw the copper in 99se? >> > >> > Thanks >> > >> >> -+- scanned by Mailsecurity Kuebler.com outgoing >> >> >> >> ____________________________________________________________ >> You are subscribed to the PEDA discussion forum >> >> To Post messages: >> mailto:[email protected] >> >> Unsubscribe and Other Options: >> http://techservinc.com/mailman/listinfo/peda_techservinc.com >> >> Browse or Search Old Archives (2001-2004): >> http://www.mail-archive.com/[EMAIL PROTECTED] >> >> Browse or Search Current Archives (2004-Current): >> http://www.mail-archive.com/[email protected] >> >> >> >> ____________________________________________________________ >> You are subscribed to the PEDA discussion forum >> >> To Post messages: >> mailto:[email protected] >> >> Unsubscribe and Other Options: >> http://techservinc.com/mailman/listinfo/peda_techservinc.com >> >> Browse or Search Old Archives (2001-2004): >> http://www.mail-archive.com/[EMAIL PROTECTED] >> >> Browse or Search Current Archives (2004-Current): >> http://www.mail-archive.com/[email protected] >> >> >> >> ____________________________________________________________ >> You are subscribed to the PEDA discussion forum >> >> To Post messages: >> mailto:[email protected] >> >> Unsubscribe and Other Options: >> http://techservinc.com/mailman/listinfo/peda_techservinc.com >> >> Browse or Search Old Archives (2001-2004): >> http://www.mail-archive.com/[EMAIL PROTECTED] >> >> Browse or Search Current Archives (2004-Current): >> http://www.mail-archive.com/[email protected] >> >> > > >____________________________________________________________ >You are subscribed to the PEDA discussion forum > >To Post messages: >mailto:[email protected] > >Unsubscribe and Other Options: >http://techservinc.com/mailman/listinfo/peda_techservinc.com > >Browse or Search Old Archives (2001-2004): >http://www.mail-archive.com/[EMAIL PROTECTED] > >Browse or Search Current Archives (2004-Current): >http://www.mail-archive.com/[email protected] > > This e-mail transmission and its attachments may contain information from Avtron Manufacturing, Inc. that is proprietary, privileged and/or confidential and is intended exclusively for the person(s) to whom it is addressed. Any use, copying, retention or disclosure by any person other than the intended recipient or the intended recipient's designees is strictly prohibited. If you have received this message in error, please notify the sender immediately by return e-mail and delete all copies. ____________________________________________________________ You are subscribed to the PEDA discussion forum To Post messages: mailto:[email protected] Unsubscribe and Other Options: http://techservinc.com/mailman/listinfo/peda_techservinc.com Browse or Search Old Archives (2001-2004): http://www.mail-archive.com/[EMAIL PROTECTED] Browse or Search Current Archives (2004-Current): http://www.mail-archive.com/[email protected]
