Maybe? perl6 -e 'lines() ==> grep /^WARN/ ==> sort() ==> join("\n") ==> say();'
HTH, Bill. On Fri, May 8, 2020 at 9:10 AM Fernando Santagata <nando.santag...@gmail.com> wrote: > > raku -e'.say for lines() ==> grep(/^WARN/) ==> sort' sample.log > > is not very satisfying because for the "for" which breaks the flow. > OTOH this > > raku -e'lines().grep(/^WARN/).sort».say' sample.log > > doesn't use the feed operator and this > > raku -e'lines() ==> grep(/^WARN/) ==> sort() ==> say()' sample.log > > outputs a list on one line, not each line on its own. This one works, but it > feels awkward: > > raku -e'lines() ==> grep(/^WARN/) ==> sort() ==> reduce({$^a ~ "\n" ~ $^b}) > ==> say()' sample.log > > On Fri, May 8, 2020 at 5:49 PM yary <not....@gmail.com> wrote: >> >> All good ideas so far, in the "more than one way to do it" spirit, can use >> "state" instead of "my", since state only initializes 1st time it's hit. >> >> raku -ne 'state @i;@i.push($_) if .starts-with(q[WARN]); END .say for >> @i.sort' sample.log >> >> Or adapting Brad's answer with the feed operator for fun >> >> raku -e 'for lines() ==> grep /^WARN/ ==> sort() {.say}' sample.log >> >> Now, I didn't want to use 'map' in there, because of a habit of only using >> 'map' when I want the return values. When looping for side-effects only, >> like saying each value in a list, I want to use 'for'. UnFORtunately though >> I cannot find anything as clean looking as >> >> raku -e 'lines() ==> grep /^WARN/ ==> sort() ==> map *.say' sample.log >> >> reading entirely L-to-R which does NOT use map... ideas? >> >> -y >> >> >> On Fri, May 8, 2020 at 10:10 AM William Michels via perl6-users >> <perl6-us...@perl.org> wrote: >> > >> > On Fri, May 8, 2020 at 5:16 AM WFB <wolfgang.banas...@gmail.com> wrote: >> > > >> > > Hi, >> > > >> > > I am trying to write an one-liner to go through all lines in a logfile >> > > and look for an certain key word, store the line and sort them before >> > > printing them out. >> > > >> > > My approach was: >> > > raku -ne "BEGIN {my @i }; @i.push($_); if $_ ~~ /^WARN/; END { >> > > @i.sort.say }" >> > > That does not work because @i does not exist in the if clause. I tried >> > > our @i as well with no luck. >> > > >> > > How can I store data that can be accessed in the END phaser? Or is there >> > > another way to archive it? TIMTOWTDI^^ >> > > >> > > One hint I found was the variable $ and @ respectively. But those >> > > variables are created for each line new... >> > > >> > > >> > > I did not found a help or examples for -npe except raku -h. Is there >> > > more helpful stuff somewhere in doc.raku.org? If so I could'nt find it. >> > > >> > > Thanks, >> > > Wolfgang >> > >> > Hi Wolfgang, >> > >> > This is a first attempt at doing what you want: I'm sure it can be >> > shortened. Since one of your requirements is doing a sort on filtered >> > values stored in an array, I abandoned use of the "-ne" one-liner >> > flag, using "-e" and "for lines()" instead. I also used grep instead >> > of smart-matching: >> > >> > perl6 -e 'my @i; for lines() {if .grep(/^WARN/) -> ($s) >> > {@i.push($s)};}; .say for @i.sort;' >> > >> > Note: the "-> ($s)" section where I store grepped matches comes from a >> > Jonathan Worthington answer found here (thanks Jonathan!): >> > >> > stackoverflow.com/questions/58982745/raku-one-line-expression-to-capture-group-from-string >> > >> > I certainly would be interested to learn if there's a phaser solution >> > to this problem (and I also have a sneaking suspicion that Supply >> > might be useful here... ). >> > >> > HTH, Bill. > > > > -- > Fernando Santagata