Author: sparky
Date: Thu Mar 16 17:37:34 2006
New Revision: 7196
Modified:
ppcrcd/trunk/conf.dir/usr/lib/ppcrcd/load-conf
ppcrcd/trunk/conf.dir/usr/lib/ppcrcd/net-detect
ppcrcd/trunk/conf.dir/usr/lib/ppcrcd/rc.live
Log:
- cleanups
Modified: ppcrcd/trunk/conf.dir/usr/lib/ppcrcd/load-conf
==============================================================================
--- ppcrcd/trunk/conf.dir/usr/lib/ppcrcd/load-conf (original)
+++ ppcrcd/trunk/conf.dir/usr/lib/ppcrcd/load-conf Thu Mar 16 17:37:34 2006
@@ -5,7 +5,7 @@
. /usr/lib/ppcrcd/functions
[EMAIL PROTECTED]@ conf: syntax:
-#@ | conf=<device>[:<modules>[:<fs>[:<file>]]]
+#@ | conf=<device>[:<modules>[:<fs>[:<file>]]]
#@ Load configuration from <device>, from <file> (if it isn't
#@ ppcrcd.xml.gz).
#@ First loads coma separated kernel modules (if needed for device)
Modified: ppcrcd/trunk/conf.dir/usr/lib/ppcrcd/net-detect
==============================================================================
--- ppcrcd/trunk/conf.dir/usr/lib/ppcrcd/net-detect (original)
+++ ppcrcd/trunk/conf.dir/usr/lib/ppcrcd/net-detect Thu Mar 16 17:37:34 2006
@@ -44,7 +44,7 @@
[EMAIL PROTECTED]@ eth:
#@ syntax:
-#@ | eth=<module>:<ip/mask>[:<gate>[:<dns1>[,<dns2>[,...]]]]
+#@ | eth=<module>:<ip/mask>[:<gate>[:<dns1>[,<dns2>[,...]]]]
#@ Configure ethernet for ethernet card supported by <module>.
#@ Note: this option may be buggy with autodetection in udev enabled.
#@ Multiple eth options are allowed.
@@ -52,7 +52,7 @@
#@ Last eth with gate specified will become default route.
#@ All dns of each eth will be added to '/etc/resolv.conf'.
#@ Example:
-#@ | eth=sungem:192.168.0.5/24:192.168.0.2:192.168.0.2
+#@ | eth=sungem:192.168.0.5/24:192.168.0.2:192.168.0.2
#@@ nonveth: don't configure ethernet specified in nvram
if cmdopt noauto; then
Modified: ppcrcd/trunk/conf.dir/usr/lib/ppcrcd/rc.live
==============================================================================
--- ppcrcd/trunk/conf.dir/usr/lib/ppcrcd/rc.live (original)
+++ ppcrcd/trunk/conf.dir/usr/lib/ppcrcd/rc.live Thu Mar 16 17:37:34 2006
@@ -19,9 +19,9 @@
[EMAIL PROTECTED]@ modpre:
#@ syntax:
-#@ | modpre=<module1>[,<module2>[,<module3>[...]]]
+#@ | modpre=<module1>[,<module2>[,<module3>[...]]]
#@ Loads modules just after udev start, before debug shell. Ex.:
-#@ | modpre=usbhid,ohci-hcd
+#@ | modpre=usbhid,ohci-hcd
#@@ nonvmodpre: don't load modules specified in nvram modpre option
modpre=$(cmdvar "modpre")
if [ -z "$modpre" ]; then
@@ -55,7 +55,7 @@
fi
#@@ verbose: be more verbose
-#@ | verbose=<L>
+#@ | verbose=<L>
#@ Sets verbosity level to <L>, (min 0, max 5). Without <L> specified it's
0.
cmdopt verbose && echo 1 > /verbose
verb=$(cmdvar verbose)
@@ -103,7 +103,7 @@
### modules ##################################################################
[EMAIL PROTECTED]@ modules=<module1>[,<module2>[,<module3>[...]]]:
#@ Adds module(s) to /etc/modules. Ex.:
-#@ | modules=therm_adt746x
+#@ | modules=therm_adt746x
#@@ nonvmodules: don't use nvram modules option
modules=$(cmdvar "modules")
if [ -z "$modules" ]; then
@@ -120,7 +120,7 @@
### keytable #################################################################
[EMAIL PROTECTED]@ keytable=<name>:
#@ Preset system keytable. Ex., spanish keytable:
-#@ | keytable=es
+#@ | keytable=es
#@@ nonvkeytable: Don't setup key table using nvram informations.
keytable=$(cmdvar "k(ey){0,1}(map|tab.*)")
if [ -z "$keytable" ]; then
_______________________________________________
pld-cvs-commit mailing list
[email protected]
http://lists.pld-linux.org/mailman/listinfo/pld-cvs-commit
