Witam
jako początkujący admin sieci domowej ;) walczę m.in. z sambą i cupsem.
Sukcesy odnoszę połowiczne, i stąd prośba o pomoc:
Sieć:
Serwerek na celku 433, 256 MB RAM
- karta sieciowa z wyjściem na świat (adres nieistotny)
- karta sieciowa z wyjściem do kompa nr. 1 - 192.168.1.1, z drugiej
strony DHCP 192.168.1.11-13
- karta sieciowa z wyjściem do kompa nr. 2 - 192.168.2.1, z drugiej
strony DHCP 192.168.2.11-13
- karta wifi - 192.168.3.1, łączy się z nią komp nr. 3 - DHCP na
192.168.3.11-13
Na serwerku biega sobie dhcp, mldonkey, samba i cups (z tych
ważniejszych rzeczy).
- DHCP działa bez problemu;
- mldonkey chodzi jak trzeba.
Samba (załączam plik z ustawieniami):
- od początku miałem problemy. Generalnie jest kilka udziałów, i działy
się z nimi od początku różne dziwne rzeczy - np. dany udział był
dostępny z jednego kompa, ale z drugiego już nie
- w tej chwili zauważyłem, że po kolejnych zabawach z konfigiem już mi
nawet nie chce browsować mojej grupy roboczej :/
Innymi słowy - kompletnie się już pogubiłem. Już kilku ładnych
instrukcji próbowałem - niestety, instrukcja z PLD dotyczy stawiania
kontrolera domeny, którego nie chcę mieć. Zdarzało się np. miałem dwa
udziały tak samo skonfigurowane, a dostęp do nich zależał od kompa z
którego się łączyłem... Help! Nic już z tego nie jarzę...
CUPS (też załączam konfiga)
- CUPS dla odmiany, po dwóch czy trzech dniach walki zaczął działać - na
kompach 1 i 2...
- co do kompa 3 - daję drukowanie strony testowej - po przesłaniu tam i
z powrotem ok. 200 MB (!!!) pakietów, co trwa ok. 20 minut, drukuje w
końcu stronę testową... Drukowania innych dokumentów zwyczajnie nie
doczekałem (może by i w końcu wydrukował...)
- na wszystkich trzech kompach są zainstalowane sterowniki HP - przy
czym 1 i 2 mogłem użyć setupu, na 3 nie mogłem, bo setup nie widział
portu drukarki (znowu :/)
- parę dni temu pytałem, jak włączyć duplekser - otóż mimo
zainstalowania sterowników drukarki pod windą, i włączeniu w tych
sterownikach automatycznego dupleksera, drukarka drukuje jednostronnie
(fakt, że nie co drugą stronę - jakby się to działo przy ręcznym druku
dwustronnym).
Panie i Panowie! Bez Waszej pomocy resztę piór z głowy sobie powyrywam!
Walczę z tym już trzeci miesiąc :/
Pozdrawiam,
Staszek
#
# "$Id: cupsd.conf.in,v 1.17 2005/01/03 19:29:45 mike Exp $"
#
# Sample configuration file for the Common UNIX Printing System (CUPS)
# scheduler.
#
# Copyright 1997-2005 by Easy Software Products, all rights reserved.
#
# These coded instructions, statements, and computer programs are the
# property of Easy Software Products and are protected by Federal
# copyright law. Distribution and use rights are outlined in the file
# "LICENSE.txt" which should have been included with this file. If this
# file is missing or damaged please contact Easy Software Products
# at:
#
# Attn: CUPS Licensing Information
# Easy Software Products
# 44141 Airport View Drive, Suite 204
# Hollywood, Maryland 20636 USA
#
# Voice: (301) 373-9600
# EMail: [EMAIL PROTECTED]
# WWW: http://www.cups.org
#
########################################################################
# #
# This is the CUPS configuration file. If you are familiar with #
# Apache or any of the other popular web servers, we've followed the #
# same format. Any configuration variable used here has the same #
# semantics as the corresponding variable in Apache. If we need #
# different functionality then a different name is used to avoid #
# confusion... #
# #
########################################################################
########
######## Server Identity
########
#
# ServerName: the hostname of your server, as advertised to the world.
# By default CUPS will use the hostname of the system.
#
# To set the default server used by clients, see the client.conf file.
#
#ServerName myhost.domain.com
#
# ServerAdmin: the email address to send all complaints/problems to.
# By default CUPS will use "[EMAIL PROTECTED]".
#
#ServerAdmin [EMAIL PROTECTED]
########
######## Server Options
########
#
# AccessLog: the access log file; if this does not start with a leading /
# then it is assumed to be relative to ServerRoot. By default set to
# "/var/log/cups/access_log"
#
# You can also use the special name "syslog" to send the output to the
# syslog file or daemon.
#
#AccessLog /var/log/cups/access_log
#
# Classification: the classification level of the server. If set, this
# classification is displayed on all pages, and raw printing is disabled.
# The default is the empty string.
#
#Classification classified
#Classification confidential
#Classification secret
#Classification topsecret
#Classification unclassified
#
# ClassifyOverride: whether to allow users to override the classification
# on printouts. If enabled, users can limit banner pages to before or
# after the job, and can change the classification of a job, but cannot
# completely eliminate the classification or banners.
#
# The default is off.
#
#ClassifyOverride off
#
# DataDir: the root directory for the CUPS data files.
# By default "/usr/share/cups".
#
#DataDir /usr/share/cups
#
# DefaultCharset: the default character set to use. If not specified,
# defaults to "utf-8". Note that this can also be overridden in
# HTML documents...
#
#DefaultCharset utf-8
#
# DefaultLanguage: the default language if not specified by the browser.
# If not specified, the current locale is used.
#
#DefaultLanguage en
#
# DocumentRoot: the root directory for HTTP documents that are served.
# By default "/usr/lib/cups/cgi-bin".
#
#DocumentRoot /usr/lib/cups/cgi-bin
#
# ErrorLog: the error log file; if this does not start with a leading /
# then it is assumed to be relative to ServerRoot. By default set to
# "/var/log/cups/error_log"
#
# You can also use the special name "syslog" to send the output to the
# syslog file or daemon.
#
#ErrorLog /var/log/cups/error_log
#
# FileDevice: determines whether the scheduler will allow new printers
# to be added using device URIs of the form "file:/foo/bar". The default
# is not to allow file devices due to the potential security vulnerability
# and due to the fact that file devices do not support raw printing.
#
#FileDevice No
#
# FontPath: the path to locate all font files (currently only for pstoraster)
# By default "/usr/share/cups/fonts".
#
#FontPath /usr/share/cups/fonts
#
# LogLevel: controls the number of messages logged to the ErrorLog
# file and can be one of the following:
#
# debug2 Log everything.
# debug Log almost everything.
# info Log all requests and state changes.
# warn Log errors and warnings.
# error Log only errors.
# none Log nothing.
#
LogLevel info
#
# MaxLogSize: controls the maximum size of each log file before they are
# rotated. Defaults to 1048576 (1MB). Set to 0 to disable log rotating.
#
# NOTE: In PLD logrotate daemon performs tasks of rotating logs.
#
MaxLogSize 0
#
# PageLog: the page log file; if this does not start with a leading /
# then it is assumed to be relative to ServerRoot. By default set to
# "/var/log/cups/page_log"
#
# You can also use the special name "syslog" to send the output to the
# syslog file or daemon.
#
#PageLog /var/log/cups/page_log
#
# PreserveJobHistory: whether or not to preserve the job history after a
# job is completed, cancelled, or stopped. Default is Yes.
#
#PreserveJobHistory Yes
#
# PreserveJobFiles: whether or not to preserve the job files after a
# job is completed, cancelled, or stopped. Default is No.
#
#PreserveJobFiles No
#
# AutoPurgeJobs: automatically purge jobs when not needed for quotas.
# Default is No.
#
#AutoPurgeJobs No
#
# MaxCopies: maximum number of copies that a user can request. Default is
# 100.
#
#MaxCopies 100
#
# MaxJobs: maximum number of jobs to keep in memory (active and completed.)
# Default is 500; the value 0 is used for no limit.
#
#MaxJobs 500
#
# MaxJobsPerPrinter: maximum number of active jobs per printer. The default
# is 0 for no limit.
#
#MaxJobsPerPrinter 0
#
# MaxJobsPerUser: maximum number of active jobs per user. The default
# is 0 for no limit.
#
#MaxJobsPerUser 0
#
# MaxPrinterHistory: controls the maximum number of history collections
# in the printer-state-history attribute. Set to 0 to disable history
# data.
#
#MaxPrinterHistory 10
#
# Printcap: the name of the printcap file. Default is /etc/printcap.
# Leave blank to disable printcap file generation.
#
Printcap /etc/printcap
#
# PrintcapFormat: the format of the printcap file, currently either
# BSD or Solaris. The default is "BSD".
#
#PrintcapFormat BSD
#PrintcapFormat Solaris
#
# PrintcapGUI: the name of the GUI options panel program to associate
# with print queues under IRIX. The default is "/usr/bin/glpoptions"
# from ESP Print Pro.
#
# This option is only used under IRIX; the options panel program
# must accept the "-d printer" and "-o options" options and write
# the selected printer options back to stdout on completion.
#
#PrintcapGUI /usr/bin/glpoptions
#
# RequestRoot: the directory where request files are stored.
# By default "/var/spool/cups".
#
#RequestRoot /var/spool/cups
#
# RemoteRoot: the name of the user assigned to unauthenticated accesses
# from remote systems. By default "remroot".
#
#RemoteRoot remroot
#
# ServerBin: the root directory for the scheduler executables.
# By default "/usr/lib/cups".
#
#ServerBin /usr/lib/cups
#
# ServerRoot: the root directory for the scheduler.
# By default "/etc/cups".
#
#ServerRoot /etc/cups
#
# ServerTokens: specifies what information in provided in the Server
# header of HTTP responses. The default is Minor.
#
# ServerTokens None
# ServerTokens ProductOnly CUPS
# ServerTokens Major CUPS/1
# ServerTokens Minor CUPS/1.1
# ServerTokens Minimal CUPS/1.1.23
# ServerTokens OS CUPS/1.1.23 (uname)
# ServerTokens Full CUPS/1.1.23 (uname) IPP/1.1
#
#ServerTokens Minor
########
######## Fax Support
########
#
# FaxRetryLimit: the number of times a fax job is retried.
# The default is 5 times.
#
#FaxRetryLimit 5
#
# FaxRetryInterval: the number of seconds between fax job retries.
# The default is 300 seconds/5 minutes.
#
#FaxRetryInterval 300
########
######## Encryption Support
########
#
# ServerCertificate: the file to read containing the server's certificate.
# Defaults to "/etc/cups/ssl/server.crt".
#
#ServerCertificate /etc/cups/ssl/server.crt
#
# ServerKey: the file to read containing the server's key.
# Defaults to "/etc/cups/ssl/server.key".
#
#ServerKey /etc/cups/ssl/server.key
########
######## Filter Options
########
#
# User/Group: the user and group the server runs under. Normally this
# must be lp and sys, however you can configure things for another
# user or group as needed.
#
# Note: the server must be run initially as root to support the
# default IPP port of 631. It changes users whenever an external
# program is run, or if the RunAsUser directive is specified...
#
#User lp
#Group sys
#
# RIPCache: the amount of memory that each RIP should use to cache
# bitmaps. The value can be any real number followed by "k" for
# kilobytes, "m" for megabytes, "g" for gigabytes, or "t" for tiles
# (1 tile = 256x256 pixels.) Defaults to "8m" (8 megabytes).
#
#RIPCache 8m
#
# TempDir: the directory to put temporary files in. This directory must be
# writable by the user defined above! Defaults to "/var/spool/cups/tmp" or
# the value of the TMPDIR environment variable.
#
#TempDir /var/spool/cups/tmp
#
# FilterLimit: sets the maximum cost of all job filters that can be run
# at the same time. A limit of 0 means no limit. A typical job may need
# a filter limit of at least 200; limits less than the minimum required
# by a job force a single job to be printed at any time.
#
# The default limit is 0 (unlimited).
#
#FilterLimit 0
########
######## Network Options
########
#
# Ports/addresses that we listen to. The default port 631 is reserved
# for the Internet Printing Protocol (IPP) and is what we use here.
#
# You can have multiple Port/Listen lines to listen to more than one
# port or address, or to restrict access:
#
# Port 80
# Port 6310
# Listen hostname
# Listen hostname:80
# Listen hostname:631
# Listen 1.2.3.4
# Listen 1.2.3.4:631
#
#Listen localhost:632
#Listen 192.168.3.13:6320
#Listen 192.168.1.12:632
#Listen 192.168.1.11:631
# NOTE: Unfortunately, most web browsers don't support TLS or HTTP Upgrades
# for encryption. If you want to support web-based encryption you'll
# probably need to listen on port 443 (the "https" port...)
#
# NOTE 2: In order for the command-line and web interfaces to work, you
# must have at least one Port or Listen line that allows access from the
# local loopback address (localhost).
#
#Port 80
#Port 443
Port 631
#
# HostNameLookups: whether or not to do lookups on IP addresses to get a
# fully-qualified hostname. This defaults to Off for performance reasons...
#
#HostNameLookups On
#
# KeepAlive: whether or not to support the Keep-Alive connection
# option. Default is on.
#
#KeepAlive On
#
# KeepAliveTimeout: the timeout before Keep-Alive connections are
# automatically closed. Default is 60 seconds.
#
#KeepAliveTimeout 60
#
# MaxClients: controls the maximum number of simultaneous clients that
# will be handled. Defaults to 100.
#
#MaxClients 100
#
# MaxClientsPerHost: controls the maximum number of simultaneous clients that
# will be handled from a specific host. Defaults to 10 or 1/10th of the
# MaxClients setting, whichever is larger. A value of 0 specifies the
# automatic (10 or 1/10th) setting.
#
#MaxClientsPerHost 0
#
# MaxRequestSize: controls the maximum size of HTTP requests and print files.
# Set to 0 to disable this feature (defaults to 0.)
#
#MaxRequestSize 0
#
# Timeout: the timeout before requests time out. Default is 300 seconds.
#
#Timeout 300
########
######## Browsing Options
########
#
# Browsing: whether or not to broadcast and/or listen for CUPS printer
# information on the network. Enabled by default.
#
Browsing On
BrowseProtocols cups
BrowseOrder Deny,Allow
BrowseAllow From 192.168.0.0/255.255.0.0
#Listen 127.0.0.1:631
#Listen 192.168.1.1:631
#Listen 192.168.2.1:631
#Listen 192.168.3.1:631
#
# BrowseProtocols: which protocols to use for browsing. Can be
# any of the following separated by whitespace and/or commas:
#
# all - Use all supported protocols.
# cups - Use the CUPS browse protocol.
# slp - Use the SLPv2 protocol.
#
# The default is "cups".
#
# NOTE: If you choose to use SLPv2, it is *strongly* recommended that
# you have at least one SLP Directory Agent (DA) on your
# network. Otherwise, browse updates can take several seconds,
# during which the scheduler will not respond to client
# requests.
#
#BrowseProtocols cups
#
# BrowseAddress: specifies a broadcast address to be used. By
# default browsing information is not sent!
#
# Note: HP-UX does not properly handle broadcast unless you have a
# Class A, B, C, or D netmask (i.e. no CIDR support).
#
# Note: Using the "global" broadcast address (255.255.255.255) will
# activate a Linux demand-dial link with the default configuration.
# If you have a LAN as well as the dial-up link, use the LAN's
# broadcast address.
#
# The @LOCAL address broadcasts to all non point-to-point interfaces.
# For example, if you have a LAN and a dial-up link, @LOCAL would
# send printer updates to the LAN but not to the dial-up link.
# Similarly, the @IF(name) address sends to the named network
# interface, e.g. @IF(eth0) under Linux. Interfaces are refreshed
# automatically (no more than once every 60 seconds), so they can
# be used on dynamically-configured interfaces, e.g. PPP, 802.11, etc.
#
#BrowseAddress x.y.z.255
#BrowseAddress x.y.255.255
#BrowseAddress x.255.255.255
#BrowseAddress 255.255.255.255
#BrowseAddress @LOCAL
#BrowseAddress @IF(name)
#
# BrowseShortNames: whether or not to use "short" names for remote printers
# when possible (e.g. "printer" instead of "[EMAIL PROTECTED]".) Enabled by
# default.
#
#BrowseShortNames Yes
#
# BrowseAllow: specifies an address mask to allow for incoming browser
# packets. The default is to allow packets from all addresses.
#
# BrowseDeny: specifies an address mask to deny for incoming browser
# packets. The default is to deny packets from no addresses.
#
# Both "BrowseAllow" and "BrowseDeny" accept the following notations for
# addresses:
#
# All
# None
# *.domain.com
# .domain.com
# host.domain.com
# nnn.*
# nnn.nnn.*
# nnn.nnn.nnn.*
# nnn.nnn.nnn.nnn
# nnn.nnn.nnn.nnn/mm
# nnn.nnn.nnn.nnn/mmm.mmm.mmm.mmm
# @LOCAL
# @IF(name)
#
# The hostname/domainname restrictions only work if you have turned hostname
# lookups on!
#
#BrowseAllow address
#BrowseDeny address
#
# BrowseInterval: the time between browsing updates in seconds. Default
# is 30 seconds.
#
# Note that browsing information is sent whenever a printer's state changes
# as well, so this represents the maximum time between updates.
#
# Set this to 0 to disable outgoing broadcasts so your local printers are
# not advertised but you can still see printers on other hosts.
#
#BrowseInterval 30
#
# BrowseOrder: specifies the order of BrowseAllow/BrowseDeny comparisons.
#
#BrowseOrder allow,deny
#BrowseOrder deny,allow
#
# BrowsePoll: poll the named server(s) for printers
#
#BrowsePoll address:port
#
# BrowsePort: the port used for UDP broadcasts. By default this is
# the IPP port; if you change this you need to do it on all servers.
# Only one BrowsePort is recognized.
#
#BrowsePort 631
#
# BrowseRelay: relay browser packets from one address/network to another.
#
#BrowseRelay source-address destination-address
#BrowseRelay @IF(src) @IF(dst)
#
# BrowseTimeout: the timeout for network printers - if we don't
# get an update within this time the printer will be removed
# from the printer list. This number definitely should not be
# less the BrowseInterval value for obvious reasons. Defaults
# to 300 seconds.
#
#BrowseTimeout 300
#
# ImplicitClasses: whether or not to use implicit classes.
#
# Printer classes can be specified explicitly in the classes.conf
# file, implicitly based upon the printers available on the LAN, or
# both.
#
# When ImplicitClasses is On, printers on the LAN with the same name
# (e.g. Acme-LaserPrint-1000) will be put into a class with the same
# name. This allows you to setup multiple redundant queues on a LAN
# without a lot of administrative difficulties. If a user sends a
# job to Acme-LaserPrint-1000, the job will go to the first available
# queue.
#
# Enabled by default.
#
#ImplicitClasses On
#
# ImplicitAnyClasses: whether or not to create "AnyPrinter" implicit
# classes.
#
# When ImplicitAnyClasses is On and a local queue of the same name
# exists, e.g. "printer", "[EMAIL PROTECTED]", "[EMAIL PROTECTED]", then
# an implicit class called "Anyprinter" is created instead.
#
# When ImplicitAnyClasses is Off, implicit classes are not created
# when there is a local queue of the same name.
#
# Disabled by default.
#
#ImplicitAnyCLasses Off
#
# HideImplicitMembers: whether or not to show the members of an
# implicit class.
#
# When HideImplicitMembers is On, any remote printers that are
# part of an implicit class are hidden from the user, who will
# then only see a single queue even though many queues will be
# supporting the implicit class.
#
# Enabled by default.
#
#HideImplicitMembers On
########
######## Security Options
########
#
# SystemGroup: the group name for "System" (printer administration)
# access. The default varies depending on the operating system, but
# will be "sys", "system", or "root" (checked for in that order.)
#
#SystemGroup sys
#
# RootCertDuration: How frequently the root certificate is regenerated.
# Defaults to 300 seconds.
#
#RootCertDuration 300
#
# Access permissions for each directory served by the scheduler.
# Locations are relative to DocumentRoot...
#
# AuthType: the authorization to use:
#
# None - Perform no authentication
# Basic - Perform authentication using the HTTP Basic method.
# Digest - Perform authentication using the HTTP Digest method.
#
# (Note: local certificate authentication can be substituted by
# the client for Basic or Digest when connecting to the
# localhost interface)
#
# AuthClass: the authorization class; currently only "Anonymous", "User",
# "System" (valid user belonging to group SystemGroup), and "Group"
# (valid user belonging to the specified group) are supported.
#
# AuthGroupName: the group name for "Group" authorization.
#
# Order: the order of Allow/Deny processing.
#
# Allow: allows access from the specified hostname, domain, IP address,
# network, or interface.
#
# Deny: denies access from the specified hostname, domain, IP address,
# network, or interface.
#
# Both "Allow" and "Deny" accept the following notations for addresses:
#
# All
# None
# *.domain.com
# .domain.com
# host.domain.com
# nnn.*
# nnn.nnn.*
# nnn.nnn.nnn.*
# nnn.nnn.nnn.nnn
# nnn.nnn.nnn.nnn/mm
# nnn.nnn.nnn.nnn/mmm.mmm.mmm.mmm
# @LOCAL
# @IF(name)
#
# The host and domain address require that you enable hostname lookups
# with "HostNameLookups On" above.
#
# The @LOCAL address allows or denies from all non point-to-point
# interfaces. For example, if you have a LAN and a dial-up link,
# @LOCAL could allow connections from the LAN but not from the dial-up
# link. Similarly, the @IF(name) address allows or denies from the
# named network interface, e.g. @IF(eth0) under Linux. Interfaces are
# refreshed automatically (no more than once every 60 seconds), so
# they can be used on dynamically-configured interfaces, e.g. PPP,
# 802.11, etc.
#
# Encryption: whether or not to use encryption; this depends on having
# the OpenSSL library linked into the CUPS library and scheduler.
#
# Possible values:
#
# Always - Always use encryption (SSL)
# Never - Never use encryption
# Required - Use TLS encryption upgrade
# IfRequested - Use encryption if the server requests it
#
# The default value is "IfRequested".
#
<Location />
Order Deny,Allow
Deny From All
Allow From 127.0.0.1
Allow From 192.168.1.*
Allow From 192.168.2.*
Allow From 192.168.3.*
</Location>
#<Location /classes>
#
# You may wish to limit access to printers and classes, either with Allow
# and Deny lines, or by requiring a username and password.
#
#</Location>
#<Location /classes/name>
#
# You may wish to limit access to printers and classes, either with Allow
# and Deny lines, or by requiring a username and password.
#
#</Location>
#<Location /jobs>
#
# You may wish to limit access to job operations, either with Allow
# and Deny lines, or by requiring a username and password.
#
#</Location>
#<Location /printers>
#
# You may wish to limit access to printers and classes, either with Allow
# and Deny lines, or by requiring a username and password.
#
#</Location>
#<Location /printers/name>
#
# You may wish to limit access to printers and classes, either with Allow
# and Deny lines, or by requiring a username and password.
#
## Anonymous access (default)
#AuthType None
## Require a username and password (Basic authentication)
#AuthType Basic
#AuthClass User
## Require a username and password (Digest/MD5 authentication)
#AuthType Digest
#AuthClass User
## Restrict access to local domain
#Order Deny,Allow
#Deny From All
#Allow From .mydomain.com
#</Location>
<Location /admin>
#
# You definitely will want to limit access to the administration functions.
# The default configuration requires a local connection from a user who
# is a member of the system group to do any admin tasks. You can change
# the group name using the SystemGroup directive.
#
AuthType Basic
AuthClass System
## Restrict access to local domain
Order Deny,Allow
Deny From All
Allow From 127.0.0.1
Allow From 192.168.1.*
Allow From 192.168.2.*
Allow From 192.168.3.*
#Encryption Required
</Location>
#
# End of "$Id: cupsd.conf.in,v 1.17 2005/01/03 19:29:45 mike Exp $".
#
# This is the main Samba configuration file. You should read the
# smb.conf(5) manual page in order to understand the options listed
# here. Samba has a huge number of configurable options (perhaps too
# many!) most of which are not shown in this example
#
# Any line which starts with a ; (semi-colon) or a # (hash)
# is a comment and is ignored. In this example we will use a #
# for commentry and a ; for parts of the config file that you
# may wish to enable
#
# NOTE: Whenever you modify this file you should run the command "testparm"
# to check that you have not many any basic syntactic errors.
#
#======================= Global Settings =====================================
[global]
load printers = yes
printing = cups
printcap name = cups
printer admin = @ntadmins
workgroup = CHATA
# server string is the equivalent of the NT Description field
server string = Serwerek PLD
announce as = Serwer PLD
# This option is important for security. It allows you to restrict
# connections to machines which are on your local network. The
# following example restricts access to two C class networks and
# the "loopback" interface. For more examples of the syntax see
# the smb.conf man page
; hosts allow = 192.168.1. 192.168.2. 127.
hosts allow = 192.168. 127.
# if you want to automatically load your printer list rather
# than setting them up individually then you'll need this
# printcap name = /etc/printcap
# load printers = yes
# It should not be necessary to spell out the print system type unless
# yours is non-standard. Currently supported print systems include:
# bsd, sysv, plp, lprng, aix, hpux, qnx, cups
# printing = cups
# guest account = guest
# otherwise the user "nobody" is used
guest account = guest
# this tells Samba to use a separate log file for each machine
# that connects
log file = /var/log/samba/log.%I
# Put a capping on the size of the log files (in Kb).
max log size = 50
# Security mode. Most people will want user level security. See
# security_level.txt for details.
security = share
# Use password server option only with security = server
; password server = <NT-Server-Name>
# Password Level allows matching of _n_ characters of the password for
# all combinations of upper and lower case.
; password level = 8
; username level = 8
# You may wish to use password encryption. Please read Samba documentation.
# Do not enable this option unless you have read those documents
encrypt passwords = yes
smb passwd file = /etc/samba/smbpasswd
# The following are needed to allow password changing from Windows to
# update the Linux system password also.
encrypt passwords = yes
# NOTE2: You do NOT need these to allow workstations to change only
# the encrypted SMB passwords. They allow the Unix password
# to be kept in sync with the SMB password.
; unix password sync = Yes
; passwd program = /usr/bin/passwd %u
; passwd chat = *New*UNIX*password* %n\n *ReType*new*UNIX*password* %n\n
*passwd:*all*authentication*tokens*updated*successfully*
# Unix users can map to different SMB User names
; username map = /etc/samba/smbusers
# Using the following line enables you to customise your configuration
netbios name = PLDSERW
# of the machine that is connecting
; include = /etc/samba/smb.conf.%m
# Most people will find that this option gives better performance.
# See speed.txt and the manual pages for details
socket options = TCP_NODELAY
# Configure Samba to use multiple interfaces
# If you have multiple network interfaces then you must list them
# here. See the man page for details.
; interfaces = 192.168.12.2/24 192.168.13.2/24
interfaces = 192.168.1.1/24 192.168.2.1/24 192.168.3.1/24
# Configure remote browse list synchronisation here
# request announcement to, or browse list sync from:
# a specific host or from / to a whole subnet (see below)
; remote browse sync = 192.168.3.25 192.168.5.255
# Cause this host to announce itself to local subnets here
remote announce = 192.168.1.255 192.168.2.255 192.168.3.255
# Browser Control Options:
# set local master to no if you don't want Samba to become a master
# browser on your network. Otherwise the normal election rules apply zmiana
local master = yes
# OS Level determines the precedence of this server in master browser
# elections. The default value should be reasonable zmiana
os level = 255
# Domain Master specifies Samba to be the Domain Master Browser. This
# allows Samba to collate browse lists between subnets. Don't use this
# if you already have a Windows NT domain controller doing this job zmiana
domain master = yes
# Preferred Master causes Samba to force a local browser election on startup
# and gives it a slightly higher chance of winning the election zmiana
preferred master = yes
# Use only if you have an NT server on your network that has been
# configured at install time to be a primary domain controller.
; domain controller = <NT-Domain-Controller-SMBName>
# Enable this if you want Samba to be a domain logon server for
# Windows95 workstations.
; domain logons = yes
# If you enable domain logons then you may want a per-machine or
# per user logon script
# run a specific logon batch file per workstation (machine)
; logon script = %m.bat
# run a specific logon batch file per username
; logon script = %U.bat
# Where to store roving profiles (only for Win95 and WinNT)
netbios name = PLDSERW
# You must uncomment the [Profiles] share below
; logon path = \\%L\Profiles\%U
# All NetBIOS names must be resolved to IP Addresses
# 'Name Resolve Order' allows the named resolution mechanism to be specified
# the default order is "host lmhosts wins bcast". "host" means use the unix
# system gethostbyname() function call that will use either /etc/hosts OR
# DNS or NIS depending on the settings of /etc/host.config, /etc/nsswitch.conf
# and the /etc/resolv.conf file. "host" therefore is system configuration
# dependant. This parameter is most often of use to prevent DNS lookups
# in order to resolve NetBIOS names to IP Addresses. Use with care!
# The example below excludes use of name resolution for machines that are NOT
# on the local network segment
# - OR - are not deliberately to be known via lmhosts or via WINS.
; name resolve order = wins lmhosts bcast
# Windows Internet Name Serving Support Section:
# WINS Support - Tells the NMBD component of Samba to enable it's WINS Server
wins support = yes
# WINS Server - Tells the NMBD components of Samba to be a WINS Client
# Note: Samba can be either a WINS Server, or a WINS Client, but NOT both
; wins server = w.x.y.z
# WINS Proxy - Tells Samba to answer name resolution queries on
# behalf of a non WINS capable client, for this to work there must be
# at least one WINS Server on the network. The default is NO.
; wins proxy = yes
# DNS Proxy - tells Samba whether or not to try to resolve NetBIOS names
# via DNS nslookups. The built-in default for versions 1.9.17 is yes,
# this has been changed in version 1.9.18 to no.
dns proxy = no
# Case Preservation can be handy - system default is _no_
# NOTE: These can be set on a per share basis zmiana
preserve case = no
short preserve case = no
# Default case is normally upper case for all DOS files
; default case = lower
# Be very careful with case sensitivity - it can break things! zmiana
case sensitive = no
# Setting this to yes may cause problems when using kernel < 2.6
# This option is ignored when Windows 9x client connects
use sendfile = no
#============================ Share Definitions ==============================
# Un-comment the following and create the netlogon directory for Domain Logons
; [netlogon]
; comment = Network Logon Service
; path = /home/netlogon
; guest ok = yes
; writable = no
; share modes = no
# Un-comment the following to provide a specific roving profile share
# the default is to use the user's home directory
;[Profiles]
; path = /home/profiles
; browseable = no
; guest ok = yes
# NOTE: If you have a BSD-style print system there is no need to
# specifically define each individual printer
[printers]
comment = All Printers
path = /var/spool/samba
browseable = yes
public = yes
guest ok = yes
writeable = no
printable = yes
printer admin = root, @ntadmins, guest
# guest account = guest
# guest ok = no
# writable = no
# printable = yes
[print$]
comment = Printer Driver Download Area
path = /etc/samba/drivers
browseable = yes
guest ok = yes
read only = yes
write list = @ntadmins, root
# This one is useful for people to share files
;[tmp]
; comment = Temporary file space
; path = /tmp
; read only = no
; public = yes
# A publicly accessible directory, but read only, except for people in
# the "staff" group
;[public]
; comment = Public Stuff
; path = /home/services/samba
; public = yes
; writable = yes
; printable = no
; write list = @staff
# Other examples.
#
# A private printer, usable only by fred. Spool data will be placed in fred's
# home directory. Note that fred must have write access to the spool directory,
# wherever it is.
;[fredsprn]
; comment = Fred's Printer
; valid users = fred
; path = /homes/fred
; printer = freds_printer
; public = no
; writable = no
; printable = yes
# A private directory, usable only by fred. Note that fred requires write
# access to the directory.
;[fredsdir]
; comment = Fred's Service
; path = /usr/somewhere/private
; valid users = fred
; public = no
; writable = yes
; printable = no
# A service which has a different directory for each machine that connects
# this allows you to tailor configurations to incoming machines. You could
# also use the %u option to tailor it by user name.
# The %m gets replaced with the machine name that is connecting.
;[pchome]
; comment = PC Directories
; path = /usr/pc/%m
; public = no
; writable = yes
# A publicly accessible directory, read/write to all users. Note that all files
# created in the directory by users will be owned by the default user, so
# any user with access can delete any other user's files. Obviously this
# directory must be writable by the default user. Another user could of course
# be specified, in which case all files would be owned by that user instead.
;[public]
; path = /usr/somewhere/else/public
; public = yes
; only guest = yes
; writable = yes
; printable = no
# The following two entries demonstrate how to share a directory so that two
# users can place files there that will be owned by the specific users. In this
# setup, the directory should be writable by both users and should have the
# sticky bit set on it to prevent abuse. Obviously this could be extended to
# as many users as required.
;[myshare]
; comment = Mary's and Fred's stuff
; path = /usr/somewhere/shared
; valid users = mary fred
; public = no
; writable = yes
; printable = no
; create mask = 0765
map to guest = Bad Password
[stasheck]
path = /home/users/stasheck/
writable = yes
browseable = yes
public = no
[lwica]
path = /home/users/lwica/
writable = yes
browseable = yes
public = yes
guest ok = yes
[mldonkey]
guest ok = yes
comment = czasem dziala, a czasem nie
browseable = yes
writable = yes
public = yes
path = /home/services/mldonkey/
# path = /home/users/lwica/
# writable = yes
# browseable = yes
# public = yes
# guest ok = yes
# browseable = no
[Administrator]
path = /home/services/mldonkey/
writable = yes
browseable = yes
public = yes
[home]
path = /home/
writable = yes
browseable = yes
public = no
[homes]
writable = yes
browseable = yes
_______________________________________________
pld-users-pl mailing list
pld-users-pl@lists.pld-linux.org
http://lists.pld-linux.org/mailman/listinfo/pld-users-pl
