Witam, Instaluje PLD z nowego RescueCD, pewnie wiadome jest że na tym rescue dyski IDE są widoczne jako /dev/sdX Tak więc idąc za ciosem chciałem zrobić by właśnie w systemie było tak widoczne. Prawie dobrze, ale nie potrafię tego zrobić.
Na rescueCD mam takie moduły załadowane: [EMAIL PROTECTED] ~]# lsmod Module Size Used by ipv6 245932 12 3c59x 40488 0 mii 5120 1 3c59x uhci_hcd 21900 0 usbcore 127108 2 uhci_hcd ide_cd 39684 0 cdrom 40608 1 ide_cd ide_disk 15104 0 piix 9604 0 [permanent] ide_core 122488 3 ide_cd,ide_disk,piix sd_mod 18704 0 ata_piix 13192 0 libata 97300 1 ata_piix scsi_mod 96268 2 sd_mod,libata dmesg w załączniku. Do chroota skopiowałem /etc/modprobe.conf z rescueCD które wygląda tak: [EMAIL PROTECTED] /]# cat /etc/modprobe.conf # alias scsi_hostadapter aic7xxx alias eth0 3c59x alias scsi_hostadapter ata_piix alias usb-controller uhci-hcd initrd się generuje: [EMAIL PROTECTED] /]# geninitrd /boot/initrd-2.6.16.45-1.gz 2.6.16.45-1 -v -f Using /dev/sda1 as device for rootfs Using modules: kernel/drivers/scsi/scsi_mod.ko.gz kernel/drivers/scsi/libata.ko.gz kernel/drivers/scsi/ata_piix.ko.gz kernel/drivers/scsi/sd_mod.ko.gz kernel/fs/jbd/jbd.ko.gz kernel/fs/mbcache.ko.gz kernel/fs/ext3/ext3.ko.gz /bin/initrd-busybox -> /tmp/initrd.LhUmwO/bin/initrd-busybox Loading module [scsi_mod] without options. Loading module [libata] without options. Loading module [ata_piix] without options. Loading module [sd_mod] without options. Loading module [jbd] without options. Loading module [mbcache] without options. Loading module [ext3] without options. Setting up udev... /sbin/initrd-udevd -> /tmp/initrd.LhUmwO/sbin/udevd /etc/udev/udev.conf -> /tmp/initrd.LhUmwO/etc/udev/udev.conf Adding rootfs finding based on root= option support. Ale system nie startuje. Z ostatnich rzeczy to mam tak: # more /etc/fstab /dev/sda1 / ext3 defaults 0 0 /dev/sda2 swap swap defaults 0 0 /dev/sda3 /var ext3 defaults 0 0 /dev/sda4 /home ext3 defaults 0 0 # more /boot/grub/menu.lst # For booting Linux title Linux root (hd0,0) kernel /boot/vmlinuz root=/dev/sda1 initrd /boot/initrd Ale nie startuje maszyna. Jak coś to spróbuję wyciągnąć z konsoli przy starcie maszyny.... Ale jak ładuje moduł ata_piix, to nie znajduje dysków. Pomocy ;) -- Pozdrawiam, Paweł
[EMAIL PROTECTED] /]# dmesg Linux version 2.6.19.2-0.1 ([EMAIL PROTECTED]) (gcc version 3.3.6 (PLD Linux)) #1 Sat Jan 13 16:14:50 UTC 2007 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 00000000000a0000 (usable) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 0000000008000000 (usable) BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 128MB LOWMEM available. Entering add_active_range(0, 0, 32768) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 32768 HighMem 32768 -> 32768 early_node_map[1] active PFN ranges 0: 0 -> 32768 On node 0 totalpages: 32768 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 224 pages used for memmap Normal zone: 28448 pages, LIFO batch:7 HighMem zone: 0 pages used for memmap DMI 2.2 present. ACPI: RSDP (v000 DELL ) @ 0x000fdf50 >>> ERROR: Invalid checksum Allocating PCI resources starting at 10000000 (gap: 08000000:f7e00000) Detected 548.652 MHz processor. Built 1 zonelists. Total pages: 32512 Kernel command line: initrd=/rescue.cpi,/custom/custom.cpi root=/dev/ram0 CONF="`/dev/fd0:/rescue`;;;;;;;;;;;" BOOT_IMAGE=vmlinuz Local APIC disabled by BIOS -- you can enable it with "lapic" mapped APIC to ffffd000 (01101000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 512 (order: 9, 2048 bytes) Console: colour VGA+ 80x25 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 69572k/131072k available (1858k kernel code, 61060k reserved, 799k data, 300k init, 0k highmem) virtual kernel memory layout: fixmap : 0xfffa9000 - 0xfffff000 ( 344 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xc8800000 - 0xff7fe000 ( 879 MB) lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) .init : 0xc03ec000 - 0xc0437000 ( 300 kB) .data : 0xc02d0aaf - 0xc03989b4 ( 799 kB) .text : 0xc0100000 - 0xc02d0aaf (1858 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 1098.13 BogoMIPS (lpj=2196267) Security Framework v1.0.0 initialized Capability LSM initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 512K CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Compat vDSO mapped to ffffe000. CPU: Intel Pentium III (Katmai) stepping 03 Checking 'hlt' instruction... OK. checking if image is initramfs... it is Overmounted tmpfs Freeing initrd memory: 56401k freed NET: Registered protocol family 16 EISA bus registered PCI: PCI BIOS revision 2.10 entry at 0xfcaee, last bus=1 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: Interpreter disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI: disabled PnPBIOS: Scanning system for PnP BIOS support... PnPBIOS: Found PnP BIOS installation structure at 0xc00fe2d0 PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xe2f4, dseg 0x40 PnPBIOS: 14 nodes reported by PnP BIOS; 14 recorded by driver PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) * Found PM-Timer Bug on the chipset. Due to workarounds for a bug, * this clock source is slow. Consider trying other clock sources PCI quirk: region 0800-083f claimed by PIIX4 ACPI PCI quirk: region 0850-085f claimed by PIIX4 SMB Boot video device is 0000:01:00.0 PCI: Using IRQ router PIIX/ICH [8086/7110] at 0000:00:07.0 NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default pnp: 00:00: ioport range 0x800-0x83f has been reserved pnp: 00:00: ioport range 0x850-0x85f has been reserved PCI: Bridge: 0000:00:01.0 IO window: e000-efff MEM window: fc000000-feffffff PREFETCH window: f9000000-f9ffffff NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 4096 bind 2048) TCP reno registered Machine check exception polling timer started. audit: initializing netlink socket (disabled) audit(1175603184.224:1): initialized Total HugeTLB memory allocated, 0 Squashfs 2.2 LZMA (released 2005/07/03) (C) 2002-2005 Phillip Lougher io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Limiting direct PCI/PCI transfers. isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12ac Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:01: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:02: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A Floppy drive(s): fd0 is 1.44M FDC 0 is a National Semiconductor PC87306 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) pnp: Device 00:05 does not support activation. i8042 aux: probe of 00:05 failed with error -22 PNP: PS/2 Controller [PNP0303] at 0x60,0x64 irq 1 PNP: PS/2 controller doesn't have AUX irq; using default 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice EISA: Probing bus 0 at eisa.0 EISA: Detected 0 cards. TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI Shortcut mode Freeing unused kernel memory: 300k freed Time: tsc clocksource has been installed. input: AT Translated Set 2 keyboard as /class/input/input0 SCSI subsystem initialized libata version 2.00 loaded. ata_piix 0000:00:07.1: version 2.00ac6 ata1: PATA max UDMA/33 cmd 0x1F0 ctl 0x3F6 bmdma 0xFFA0 irq 14 ata2: PATA max UDMA/33 cmd 0x170 ctl 0x376 bmdma 0xFFA8 irq 15 scsi0 : ata_piix ata1.00: ATA-5, max UDMA/66, 29888820 sectors: LBA ata1.00: ata1: dev 0 multi count 8 ata1.00: configured for UDMA/33 scsi1 : ata_piix ata2.00: ATAPI, max UDMA/33 ata2.00: configured for UDMA/33 scsi 0:0:0:0: Direct-Access ATA Maxtor 51536U3 DA62 PQ: 0 ANSI: 5 scsi 1:0:0:0: CD-ROM TOSHIBA CD-ROM XM-1902B 1J21 PQ: 0 ANSI: 5 SCSI device sda: 29888820 512-byte hdwr sectors (15303 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 29888820 512-byte hdwr sectors (15303 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 sda4 sd 0:0:0:0: Attached scsi disk sda Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb USB Universal Host Controller Interface driver v3.0 PCI: setting IRQ 11 as level-triggered PCI: Found IRQ 11 for device 0000:00:07.2 PCI: Sharing IRQ 11 with 0000:00:11.0 uhci_hcd 0000:00:07.2: UHCI Host Controller uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:07.2: irq 11, io base 0x0000dce0 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected PCI: Found IRQ 11 for device 0000:00:11.0 PCI: Sharing IRQ 11 with 0000:00:07.2 3c59x: Donald Becker and others. www.scyld.com/network/vortex.html 0000:00:11.0: 3Com PCI 3c905B Cyclone 100baseTx at c8864000. eth0: setting full-duplex. NET: Registered protocol family 10 lo: Disabled Privacy Extensions Mobile IPv6 eth0: no IPv6 routers present kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sda3, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sda4, internal journal EXT3-fs: mounted filesystem with ordered data mode.
_______________________________________________ pld-users-pl mailing list pld-users-pl@lists.pld-linux.org http://lists.pld-linux.org/mailman/listinfo/pld-users-pl