>> How do I configure a second nic (pci if that matters)?
>
> Basic setup is done in /etc/modules.conf - load the nic drivers and setup an
> alias for each eth. This is an example of one of my boxes
> (/etc/modules.conf):
>
> alias eth0 tulip
> alias eth1 via-rhine
>
> Then, it's a matter of setting the ifcfg-eth? to auto-load and determine IP
> configuration etc. just like if you had only one nic. If you're setting up a
> gateway you'll need to configure at least a ip_forward = 1 and determine a
> route between the nic's.
>
> > as soon as the second nic is installed, i lost everything.
>
> Make sure that each driver is aliases to different /dev/eth and it should
> work (has worked great for 5 years for me).
>
> Regards
> Peter Larsen
Thanks, did as you said but it didn't work. :-(
Following is more accurate info. Eventual idea is Home LAN, 2 machines,
both linux, this machine is hooked to DSL (perm. IP),
eth0, and other machine hooks to this via eth1.
At boot everything works:
[donius@warwick donius]$ /sbin/ifconfig
eth0 Link encap:Ethernet HWaddr 00:03:6D:1F:D2:44
<PROPER WORKING ADDRESSES HERE>
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:200 errors:0 dropped:0 overruns:0 frame:0
TX packets:222 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:92527 (90.3 Kb) TX bytes:28723 (28.0 Kb)
Interrupt:10 Base address:0x9000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:152 errors:0 dropped:0 overruns:0 frame:0
TX packets:152 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:7696 (7.5 Kb) TX bytes:7696 (7.5 Kb)
But if i activate eth1, now eth0 looses capabilities.
[donius@warwick donius]$ /sbin/ifconfig
eth0 Link encap:Ethernet HWaddr 00:03:6D:1F:D2:44
<PROPER WORKING ADDRESSES HERE>
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:200 errors:0 dropped:0 overruns:0 frame:0
TX packets:222 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:92527 (90.3 Kb) TX bytes:28723 (28.0 Kb)
Interrupt:10 Base address:0x9000
eth1 Link encap:Ethernet HWaddr 00:03:6D:1F:D3:15
inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:10 dropped:0 overruns:0 carrier:20
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:12 Base address:0xb000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:156 errors:0 dropped:0 overruns:0 frame:0
TX packets:156 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:8048 (7.8 Kb) TX bytes:8048 (7.8 Kb)
I know nothing about networking and am starting to think i should post
there, but i really have found you bunch of guys to be so helpful w/ my
problems, i wanted to try here first.
thanks for the info so far, dw.
--
Psyche-list mailing list
[EMAIL PROTECTED]
https://listman.redhat.com/mailman/listinfo/psyche-list
