I switched the cd-rw on primary slave status and it worked fine!
Great work! anyways, at this moment I want to know the reason behind all
of this mess so in the future I would be able to troubleshoot even more
possible problems and be able to explain it further more
thanks!
On Sat, 2003-01-18 at 02:10, Randy Kelsoe wrote:
> Banjo Donila wrote:
> > I'm having problems when mounting on this cd-rw. Well the installation
> > went very good but after installation and mounting a cdrom it locks up
> > and produces this messages and totally locks up my box.
> >
> > It has the latest kernel version (redhat kernel)
> > so here's the interesting /var/log/message goes:
> > kernel: Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
> > kernel: sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
> > kernel: Uniform CD-ROM driver Revision: 3.12
> > kernel: scsi : aborting command due to timeout : pid 15, scsi0, channel
> > 0, id 0, lun 0 Read (10) 00 00 00 00 10 00 00 01 00
> > kernel: hdd: timeout waiting for DMA
> > kernel: ide_dmaproc: chipset supported ide_dma_timeout func only: 14
> > kernel: hdd: status timeout: status=0xd0 { Busy }
> > kernel: hdd: drive not ready for command
> > kernel: scsi : aborting command due to timeout : pid 15, scsi0, channel
> > 0, id 0, lun 0 Read (10) 00 00 00 00 10 00 00 01 00
> > kernel: SCSI host 0 abort (pid 15) timed out - resetting
> > kernel: ide1: reset timed-out, status=0x90
> > kernel: hdd: status timeout: status=0x90 { Busy }
> > kernel: hdd: drive not ready for command
> > ---the line below goes all over and over again----
> > kernel: scsi : aborting command due to timeout : pid 15, scsi0, channel
> > 0, id 0, lun 0 Read (10) 00 00 00 00 10 00 00 01 00
> > kernel: SCSI host 0 abort (pid 15) timed out - resetting
> > kernel: SCSI bus is being reset for host 0 channel 0.
> >
> > ive been looking for a specific driver for my cd-rw but I wasnt able to
> > find any the box is using AMD-K6 500Mhz 128MB thanks alot!
> >
>
> First, look in your /etc/grub.conf file and make sure you have an entry
> that looks like this:
>
> kernel /vmlinuz-2.4.18-18.8.0 ro root=LABEL=/ hdd=ide-scsi
>
> The "hdd=ide-scsi" is important. Also, do an lsmod and make sure you
> see something like:
>
> ide-scsi 9616 0
> scsi_mod 102248 2 [sr_mod ide-scsi]
> ide-cd 31432 0
> cdrom 30976 0 [sr_mod ide-cd]
>
> This problem looks like a bad CDRW to me. The drive is recognized by the
> system, but is not ready for some reason (kernel: hdd: status timeout:
> status=0xd0 { Busy } )
>
> This is setup as a slave drive on the secondary IDE. Do you have a
> master on that channel? If not, make the CDRW a master drive, or if you
> can move it to the primary IDE, as a slave, that would rule out a bad
> secodary IDE channel.
>
> There is not specific driver, it should work with the generic ide-scsi
> cdrom driver.
>
>
>
>
>
>
> --
> Psyche-list mailing list
> [EMAIL PROTECTED]
> https://listman.redhat.com/mailman/listinfo/psyche-list
>
--
Psyche-list mailing list
[EMAIL PROTECTED]
https://listman.redhat.com/mailman/listinfo/psyche-list
