No, the bond isn't created on system boot. Thus the bridge that should connect the bond with the VMs is created but the connection is not made.
Am 21.07.21 um 18:41 schrieb Gilberto Ferreira: > So did you solve the issue? > --- > Gilberto Nunes Ferreira > (47) 99676-7530 - Whatsapp / Telegram > > > > > > > Em qua., 21 de jul. de 2021 às 12:49, Uwe Sauter <[email protected] > <mailto:[email protected]>> escreveu: > > Hi Gilberto, > > thanks for that tip. Unfortunately the network configuration quits a few > steps before the bridge is > configured. The needed bond0 is not created… > > > Regards, > > Uwe > > > Am 21.07.21 um 17:45 schrieb Gilberto Ferreira: > > Perhaps you need to change or add this feature in the network interface > file: > > > > > https://pve.proxmox.com/wiki/Upgrade_from_6.x_to_7.0#Linux_Bridge_MAC-Address_Change > > <https://pve.proxmox.com/wiki/Upgrade_from_6.x_to_7.0#Linux_Bridge_MAC-Address_Change> > > > <https://pve.proxmox.com/wiki/Upgrade_from_6.x_to_7.0#Linux_Bridge_MAC-Address_Change > > <https://pve.proxmox.com/wiki/Upgrade_from_6.x_to_7.0#Linux_Bridge_MAC-Address_Change>> > > > > > > > > --- > > Gilberto Nunes Ferreira > > (47) 99676-7530 - Whatsapp / Telegram > > > > > > > > > > > > > > Em qua., 21 de jul. de 2021 às 12:18, Uwe Sauter > <[email protected] > <mailto:[email protected]> > > <mailto:[email protected] <mailto:[email protected]>>> > escreveu: > > > > Hi all, > > > > Fresh installation of PVE 7 with all available updates. > > > > It looks like I'm unable to configure bonding of two interfaces > using LCAP. > > > > Output from "ip a": > > 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN > group default qlen 1000 > > link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 > > inet 127.0.0.1/8 <http://127.0.0.1/8> <http://127.0.0.1/8 > <http://127.0.0.1/8>> scope > host lo > > valid_lft forever preferred_lft forever > > inet6 ::1/128 scope host > > valid_lft forever preferred_lft forever > > 2: eno1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master > vmbr1224 state UP > group default > > qlen 1000 > > link/ether a4:bf:01:2f:63:f2 brd ff:ff:ff:ff:ff:ff > > altname enp24s0f0 > > 3: enp59s0f4: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 9000 qdisc mq > state UP group default > qlen 1000 > > link/ether 00:07:43:18:82:70 brd ff:ff:ff:ff:ff:ff > > inet6 fe80::207:43ff:fe18:8270/64 scope link > > valid_lft forever preferred_lft forever > > 4: enp59s0f4d1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 9000 qdisc mq > state UP group default > qlen 1000 > > link/ether 00:07:43:18:82:78 brd ff:ff:ff:ff:ff:ff > > inet6 fe80::207:43ff:fe18:8278/64 scope link > > valid_lft forever preferred_lft forever > > 5: eno2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group > default qlen 1000 > > link/ether a4:bf:01:2f:63:f3 brd ff:ff:ff:ff:ff:ff > > altname enp24s0f1 > > 6: ibp94s0: <BROADCAST,MULTICAST> mtu 2044 qdisc noop state DOWN > group default qlen 256 > > link/infiniband > 80:00:0a:08:fe:80:00:00:00:00:00:00:f4:52:14:03:00:2c:14:51 brd > > 00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff > > 7: ibp94s0d1: <BROADCAST,MULTICAST> mtu 2044 qdisc noop state DOWN > group default qlen 256 > > link/infiniband > 80:00:0a:09:fe:80:00:00:00:00:00:00:f4:52:14:03:00:2c:14:52 brd > > 00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff > > 8: vmbr1224: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc > noqueue state UP group default > > qlen 1000 > > link/ether a4:bf:01:2f:63:f2 brd ff:ff:ff:ff:ff:ff > > inet 10.224.203.1/16 <http://10.224.203.1/16> > <http://10.224.203.1/16 > <http://10.224.203.1/16>> scope global vmbr1224 > > valid_lft forever preferred_lft forever > > inet6 fe80::a6bf:1ff:fe2f:63f2/64 scope link > > valid_lft forever preferred_lft forever > > > > > > My current /etc/network/interfaces, which is missing the bridges > for the VMs: > > auto lo > > iface lo inet loopback > > > > auto eno1 > > iface eno1 inet manual > > > > auto enp59s0f4 > > iface enp59s0f4 inet manual > > mtu 9000 > > > > auto enp59s0f4d1 > > iface enp59s0f4d1 inet manual > > mtu 9000 > > > > auto bond0 > > iface bond0 inet manual > > slaves enp59s0f4 enp59s0f4d1 > > bond-downdelay 200 > > bond-miimon 100 > > bond-mode 802.3ad > > bond-updelay 200 > > > > auto vmbr1224 > > iface vmbr1224 inet static > > address 10.224.203.1 > > netmask 255.255.0.0 > > gateway 10.224.200.1 > > bridge_ports eno1 > > bridge_stp off > > bridge_fd 0 > > > > ## # VLAN 155 nativ on bond0 > > ## auto vmbr155 > > ## iface vmbr155 inet manual > > ## mtu 9000 > > ## bridge_ports bond0 > > ## bridge_stp off > > ## bridge_fd 0 > > > > > > This config was copied over from the PVE 6 installation on the same > host which experienced > a SSD > > failure and thus was re-installed with PVE 7. > > > > > > Am I missing something? Am I being blind? > > > > > > Any help is appreciated. > > > > > > Thanks, > > > > Uwe > > > > > > > > > > _______________________________________________ > > pve-user mailing list > > [email protected] <mailto:[email protected]> > <mailto:[email protected] <mailto:[email protected]>> > > https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user > <https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user> > > <https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user > <https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user>> > > > _______________________________________________ pve-user mailing list [email protected] https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user
