I have Openvswitch bonds working fine for years now, but in older versions of Proxmox (6.4-4 and 5.3-5):
-------------- auto eno2 iface eno2 inet manual auto eno1 iface eno1 inet manual allow-vmbr0 ath iface ath inet static address 10.NN.NN.38/26 gateway 10.NN.NN.1 ovs_type OVSIntPort ovs_bridge vmbr0 ovs_options tag=100 . . allow-vmbr0 bond0 iface bond0 inet manual ovs_bonds eno1 eno2 ovs_type OVSBond ovs_bridge vmbr0 ovs_options bond_mode=balance-slb lacp=active allow-ovs vmbr0 iface vmbr0 inet manual ovs_type OVSBridge ovs_ports bond0 ath lan dmz_vod ampr -------- I think now, "allow-vmbr0" and "allow-ovs" are replaced with "auto". This bond works fine with HP, 3COM, HUAWEI, and MIKROTIK switches. Several OVSIntPort VLANS are attached to it. I also had 10G bonds (Intel, Supermicro inter-server links), with the same result. I see the only difference with your setup is the bond_mode. Switch setup is also very important to match this. On Fri, Jan 21, 2022 at 1:23 PM Сергей Цаболов <[email protected]> wrote: > Hello, > > I have PVE cluster and I thinking to install on the pve-7 openvswitch > for can move and add VM from other networks and Proxmox Cluster > > With base Linux bridge all work well without problem with 2 interface > 10GB ens1f0np0 ens1f12np0 > > I install openvswitch with manual > https://pve.proxmox.com/wiki/Open_vSwitch > > I want use Fiber 10GB interfaces ens1f0np0 ens1f12np0 with Bond I think. > > I try some settings but is not working. > > My setup in interfaces: > > auto lo > iface lo inet loopback > > auto ens1f12np0 > iface ens1f12np0 inet manual > #Fiber > > iface idrac inet manual > > iface eno2 inet manual > > iface eno3 inet manual > > iface eno4 inet manual > > auto ens1f0np0 > iface ens1f0np0 inet manual > > iface eno1 inet manual > > auto inband > iface inband inet static > address 10.10.29.10/24 > gateway 10.10.29.250 > ovs_type OVSIntPort > ovs_bridge vmbr0 > #Proxmox Web Access > > auto vlan10 > iface vlan10 inet manual > ovs_type OVSIntPort > ovs_bridge vmbr0 > ovs_options tag=10 > #Network 10 > > auto bond0 > iface bond0 inet manual > ovs_bonds ens1f0np0 ens1f12np0 > ovs_type OVSBond > ovs_bridge vmbr0 > ovs_mtu 9000 > ovs_options bond_mode=active-backup > > auto vmbr0 > iface vmbr0 inet manual > ovs_type OVSBridge > ovs_ports bond0 inband vlan10 > ovs_mtu 9000 > #inband > > > Can some one help me if I set all correctly or not? > > If someone have setup openvswitch with Bond interfaces 10GB share with > me configuration. > > Thank at lot. > > > Sergey TS > The best Regard > > _______________________________________________ > pve-user mailing list > [email protected] > https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user > > _______________________________________________ > pve-user mailing list > [email protected] > https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user > _______________________________________________ pve-user mailing list [email protected] https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user
