Hallo I'm not able to run dvb-t on Hauppauge WinTv-HVR-1900.
My distribution is Arch Linux with kernel 2.6.30.6 I followed the instructions on the page 'pvrusb2 driver setup information': - Extracted firmware from CD WinTV-v7: v4l-cx2341x-enc.fw, v4l-cx25840.fw,v4l-pvrusb2-73xxx-01.fw, and copied to /lib/firmware - Compiled and installed OK Standalone driver (pvrusb2-mci-20100221) Analog section seems working well, but digital section (dvb-t) seems not work. I have tried: echo "dtv" > /sys/class/pvrusb2/sn-7061042/ctl_input/cur_val echo "818000000" > /sys/class/pvrusb2/sn-7061042/ctl_frequency/cur_val scan -v -c With the output: using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' WARNING: filter timeout pid 0x0011 WARNING: filter timeout pid 0x0000 dumping lists (0 services) Done. w_scan -c IT -X With the output: w_scan version 20091230 (compiled for DVB API 5.0) using settings for ITALY DVB aerial DVB-T Europe frontend_type DVB-T, channellist 4 output format czap/tzap/szap/xine Info: using DVB adapter auto detection. /dev/dvb/adapter0/frontend0 -> DVB-T "NXP TDA10048HN DVB-T": good :-) Using DVB-T frontend (adapter /dev/dvb/adapter0/frontend0) -_-_-_-_ Getting frontend capabilities-_-_-_-_ Using DVB API 5.0 frontend NXP TDA10048HN DVB-T supports INVERSION_AUTO QAM_AUTO TRANSMISSION_MODE_AUTO GUARD_INTERVAL_AUTO HIERARCHY_AUTO FEC_AUTO -_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_-_ Scanning 7MHz frequencies... . . . . Scanning 8MHz frequencies... . . . . ERROR: Sorry - i couldn't get any working frequency/transponder Nothing to scan!! cat /dev/dvb/adapter0/dvr0 with no output vlc dvb-t:// :dvb-frequency=818000000 :dvb-bandwidth=8 --program=141 not working vlc dvb-t:// :dvb-bandwidth=8 --program=141 not working with a lot of error messages dvbstream -f 818000 710 711 -o > test.ts dvbstream 710 711 -o > test.ts with zero lenght of test.ts I have also tried Compilation and installation of the last tarball of the in-V4L driver (rev 14494) and Compilation and installation of the last standalone driver combined with out-of-tree V4L (rev 14494). The results are the same as before. Some install and debug informations: dmesg: pvrusb2: Hardware description: WinTV HVR-1900 Model 73xxx pvrusb2: Binding ir_video to i2c address 0x71. cx25840 1-0044: cx25843-24 found @ 0x88 (pvrusb2_a) pvrusb2: Attached sub-driver cx25840 tuner 1-0042: chip found @ 0x84 (pvrusb2_a) pvrusb2: Attached sub-driver tuner cx25840 1-0044: firmware: requesting v4l-cx25840.fw cx25840 1-0044: loaded v4l-cx25840.fw firmware (16382 bytes) tveeprom 1-00a2: Hauppauge model 73219, rev D1F5, serial# 7061042 tveeprom 1-00a2: MAC address is 00-0D-FE-6B-BE-32 tveeprom 1-00a2: tuner model is NXP 18271C2 (idx 155, type 54) tveeprom 1-00a2: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) ATSC/DVB Digital (eeprom 0xf4) tveeprom 1-00a2: audio processor is CX25843 (idx 37) tveeprom 1-00a2: decoder processor is CX25843 (idx 30) tveeprom 1-00a2: has radio, has IR receiver, has IR transmitter pvrusb2: Supported video standard(s) reported available in hardware: PAL-B/B1/D/D1/G/H/I/K;SECAM-B/D/G/H/K/K pvrusb2: Based on hardware available list, also supporting: PAL-N/Nc pvrusb2: Mapping standards mask=0x3ff06ff (PAL-B/B1/D/D1/G/H/I/K/N/Nc;SECAM-B/D/G/H/K/K1/L/LC;ATSC-8VSB/16VSB) pvrusb2: Setting up 22 unique standard(s) pvrusb2: Set up standard idx=0 name=PAL-B/G pvrusb2: Set up standard idx=1 name=PAL-D/K pvrusb2: Set up standard idx=2 name=SECAM-B/G pvrusb2: Set up standard idx=3 name=SECAM-D/K pvrusb2: Set up standard idx=4 name=PAL-B pvrusb2: Set up standard idx=5 name=PAL-B1 pvrusb2: Set up standard idx=6 name=PAL-G pvrusb2: Set up standard idx=7 name=PAL-H pvrusb2: Set up standard idx=8 name=PAL-I pvrusb2: Set up standard idx=9 name=PAL-D pvrusb2: Set up standard idx=10 name=PAL-D1 pvrusb2: Set up standard idx=11 name=PAL-K pvrusb2: Set up standard idx=12 name=PAL-N pvrusb2: Set up standard idx=13 name=PAL-Nc pvrusb2: Set up standard idx=14 name=SECAM-B pvrusb2: Set up standard idx=15 name=SECAM-D pvrusb2: Set up standard idx=16 name=SECAM-G pvrusb2: Set up standard idx=17 name=SECAM-H pvrusb2: Set up standard idx=18 name=SECAM-K pvrusb2: Set up standard idx=19 name=SECAM-K1 pvrusb2: Set up standard idx=20 name=SECAM-L pvrusb2: Set up standard idx=21 name=SECAM-LC pvrusb2: Initial video standard auto-selected to PAL-B/G pvrusb2: Device initialization completed successfully. pvrusb2: registered device video0 [mpeg] DVB: registering new adapter (pvrusb2-dvb) tda829x 1-0042: setting tuner address to 60 tda18271 1-0060: creating new instance TDA18271HD/C2 detected @ 1-0060 tda18271: performing RF tracking filter calibration lsmod |grep pvrusb: pvrusb2 150564 0 cx2341x 13160 1 pvrusb2 v4l2_common 14244 4 tuner,cx25840,pvrusb2,cx2341x tda8290 13352 2 tuner,pvrusb2 tda18271 35756 2 pvrusb2,tda8290 s5h1409 9096 1 pvrusb2 s5h1411 9960 1 pvrusb2 videodev 36544 4 tuner,cx25840,pvrusb2,v4l2_common v4l1_compat 15688 2 pvrusb2,videodev tda10048 8712 1 pvrusb2 tuner_simple 14928 2 tuner,pvrusb2 lgdt330x 8808 1 pvrusb2 dvb_core 86816 2 pvrusb2,lgdt330x tveeprom 11880 1 pvrusb2 i2c_core 22776 21 tuner,tea5767,tuner_xc2028,xc5000,tda9887,mt20xx,tea5761,cx25840,pvrusb2,v4l2_common,tda8290,tda18271,tda827x,s5h1409,s5h1411,tda10048,tuner_simple,lgdt330x,tveeprom,drm,i2c_viapro usbcore 150160 4 pvrusb2,uhci_hcd,ehci_hcd cat /sys/class/pvrusb2/sn-7061042/debuginfo: Driver hardware description: WinTV HVR-1900 Model 73xxx Driver state info: driver: <ok> <init> <connected> <mode=digital> pipeline: <idle> <configok> worker: <decode:quiescent> <encode:init> <encode:virgin> <encode:waitok> <usb:stop> <pathway:ok> state: ready Hardware supported inputs: television, dtv, composite, s-video Bytes streamed=0 URBs: queued=0 idle=0 ready=0 processed=0 failed=0 ir scheme: id=2 Zilog Associated v4l2-subdev drivers and I2C clients: cx25840: cx25840 @ 44 tuner: tuner @ 42 Any suggestions? Thanks in advance. _______________________________________________ pvrusb2 mailing list [email protected] http://www.isely.net/cgi-bin/mailman/listinfo/pvrusb2
