Product: [1]
Datasheet: [2]
ADC128D818 Support:
- channel readings from pre-set values
- driver can read and write most configuration registers
ADC128D818 currently unsupported:
- slave address restriction
- startup sequence and realistic busy register emulation
- external VREF
- conversion rate
- interrupts
- deep shutdown mode
- individual channel shutdown
- selection between Mode 0,1,2,3
- pseudo-differential input
Anyone could expand it in the future for more accurate emulation.
The reason for adding this device is to support Yosemite V4 emulation.
Tested: on yosemite v4 qemu
initialize the device:
// ti,adc128d818 @ 0x1f (adc)
// the driver will throw away the last 4 bits, set them 0
uint16_t adc_values1[8] = {
0b011110000000, 0b010100010000,
0b001000110000, 0b100000100000,
0b011110000000, 0b010100010000,
0b001000110000, 0b100000100000};
adc128d818_init_with_values(bus, 0x1f, adc_values1, 8);
Trace outputs directly after initialization:
adc128d818_realize i2c_addr: 0x1f
adc128d818_realize i2c_addr: 0x1f
adc128d818_event i2c_addr: 0x1f, event: 0x01
adc128d818_send i2c_addr: 0x1f, data: 0x00
adc128d818_send i2c_addr: 0x1f, data: 0x80
adc128d818_write i2c_addr: 0x1f, reg: 0x00 data: 0x80
adc128d818_event i2c_addr: 0x1f, event: 0x03
adc128d818_event i2c_addr: 0x1f, event: 0x01
...
read the values
root@yosemite4:/sys/bus/i2c/devices/30-001f# cat hwmon/hwmon0/in0_min
0
root@yosemite4:/sys/bus/i2c/devices/30-001f# cat hwmon/hwmon0/in0_max
0
root@yosemite4:/sys/bus/i2c/devices/30-001f# cat hwmon/hwmon0/in0_input
75
root@yosemite4:/sys/bus/i2c/devices/30-001f# cat hwmon/hwmon0/name
adc128d818
We initially configured 0b011110000000 for the first channel.
The driver throws away the last 4 bits and does calculation similar to
below:
val = DIV_ROUND_CLOSEST(data->in[index][nr] * data->vref, 4095);
We can check that the calculation is as expected given our configured
value.
((0b011110000000 >> 4) * 2560) / 4095
75.01831501831502
References:
[1] https://www.ti.com/product/ADC128D818
[2] https://www.ti.com/lit/gpn/adc128d818
Cc: Titus Rwantare <[email protected]>
Cc: "Cédric Le Goater" <[email protected]> (maintainer:ASPEED BMCs)
Cc: Paolo Bonzini <[email protected]> (maintainer:Kconfig)
Cc: Peter Maydell <[email protected]> (supporter:ARM TCG CPUs)
Cc: "Philippe Mathieu-Daudé" <[email protected]> (odd fixer:Overall sensors)
Cc: [email protected] (open list:ARM TCG CPUs)
Cc: [email protected] (open list:All patches CC here)
Signed-off-by: Alexander Hansen <[email protected]>
---
MAINTAINERS | 1 +
include/hw/sensor/adc128d818.h | 20 ++
hw/arm/aspeed_ast2600_fby4.c | 9 +-
hw/sensor/adc128d818.c | 410 +++++++++++++++++++++++
hw/arm/Kconfig | 1 +
hw/sensor/Kconfig | 4 +
hw/sensor/meson.build | 1 +
hw/sensor/trace-events | 8 +
tests/functional/arm/test_aspeed_fby4.py | 10 +
9 files changed, 463 insertions(+), 1 deletion(-)
create mode 100644 include/hw/sensor/adc128d818.h
create mode 100644 hw/sensor/adc128d818.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 669d6e8344..bf4d157781 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3984,6 +3984,7 @@ PMBus
M: Titus Rwantare <[email protected]>
S: Maintained
F: hw/i2c/pmbus_device.c
+F: hw/sensor/adc128d818.c
F: hw/sensor/adm1272.c
F: hw/sensor/isl_pmbus_vr.c
F: hw/sensor/max11615.c
diff --git a/include/hw/sensor/adc128d818.h b/include/hw/sensor/adc128d818.h
new file mode 100644
index 0000000000..e2bdc47590
--- /dev/null
+++ b/include/hw/sensor/adc128d818.h
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+#ifndef QEMU_ADC128D818_H
+#define QEMU_ADC128D818_H
+
+#include <stdint.h>
+#include "hw/i2c/i2c.h"
+
+#define TYPE_ADC128D818 "adc128d818"
+
+/*
+ * Create and realize a adc128d818 ADC with constant caller-supplied readings
+ * @bus: I2C bus to put it on
+ * @address: I2C address
+ * @init_values: array of readings for each ADC channel
+ * @init_values_size: Size of @init_values, can be less than the number of
channels
+ */
+I2CSlave *adc128d818_init_with_values(I2CBus *bus, uint8_t address,
+ const uint16_t *init_values, uint32_t
init_values_size);
+
+#endif
diff --git a/hw/arm/aspeed_ast2600_fby4.c b/hw/arm/aspeed_ast2600_fby4.c
index 45ed4a4c0f..c70ef43a61 100644
--- a/hw/arm/aspeed_ast2600_fby4.c
+++ b/hw/arm/aspeed_ast2600_fby4.c
@@ -12,6 +12,7 @@
#include "hw/arm/aspeed_soc.h"
#include "hw/nvram/eeprom_at24c.h"
#include "hw/sensor/max11615.h"
+#include "hw/sensor/adc128d818.h"
#include "hw/i2c/i2c_mux_pca954x.h"
#include "hw/gpio/pca9552.h"
@@ -162,7 +163,13 @@ static void fby4_i2c_init_fanboard(I2CSlave *fan_mux,
size_t eepromSize)
I2CBus *bus = pca954x_i2c_get_bus(fan_mux, i);
/* ti,adc128d818 @ 0x1f (adc) */
- /* TODO */
+ /* the driver will throw away the last 4 bits, set them 0 */
+ static const uint16_t adc_values1[8] = {
+ 0b011110000000, 0b010100010000,
+ 0b001000110000, 0b100000100000,
+ 0b011110000000, 0b010100010000,
+ 0b001000110000, 0b100000100000};
+ adc128d818_init_with_values(bus, 0x1f, adc_values1, 8);
/* maxim,max31790 @ 0x20 (pwm) */
i2c_slave_create_simple(bus, "max31790", 0x20);
diff --git a/hw/sensor/adc128d818.c b/hw/sensor/adc128d818.c
new file mode 100644
index 0000000000..e362e41788
--- /dev/null
+++ b/hw/sensor/adc128d818.c
@@ -0,0 +1,410 @@
+/*
+ * Texas Instruments ADC128D818 12 bit ADC with temperature sensor
+ * Models ADC128D818
+ *
+ * Product: https://www.ti.com/product/ADC128D818
+ * Datasheet: https://www.ti.com/lit/gpn/adc128d818
+ *
+ * Copyright 2026 9elements
+ *
+ * SPDX-License-Identifier: GPL-2.0-or-later
+ */
+
+#include "qemu/osdep.h"
+#include "hw/i2c/i2c.h"
+#include "migration/vmstate.h"
+#include "qapi/error.h"
+#include "qapi/visitor.h"
+#include "qemu/log.h"
+#include "qemu/module.h"
+#include "trace.h"
+#include "hw/sensor/adc128d818.h"
+
+/* 8 bit, r/w */
+#define REG_CONFIG 0x00
+
+/* 8 bit, readonly */
+#define REG_INTERRUPT_STATUS 0x01
+
+/* 8 bit, r/w */
+#define REG_INTERRUPT_MASK 0x03
+
+/* 8 bit, r/w */
+#define REG_CONVERSION_RATE 0x07
+
+/* 8 bit, r/w */
+#define REG_CHANNEL_DISABLE 0x08
+
+/* 8 bit, write-only */
+#define REG_ONE_SHOT 0x09
+
+/* 8 bit, r/w */
+#define REG_DEEP_SHUTDOWN 0x0a
+
+/* 8 bit, r/w */
+#define REG_ADVANCED_CONFIG 0x0b
+
+/* 8 bit, readonly */
+#define REG_BUSY_STATUS 0x0c
+
+/* 16 bit registers, N = 0..7, readonly */
+#define REG_CHANNEL_READING(N) (0x20 + N)
+
+/* 8 bit registers N = 0..15, r/w */
+#define REG_LIMIT(N) (0x2a + N)
+
+/* 8 bit register, readonly */
+#define REG_MANUFACTURER_ID 0x3e
+
+/* 8 bit register, readonly */
+#define REG_REVISION_ID 0x3f
+
+#define ADC128D818_NUM_CHANNELS 8
+
+struct ADC128D818State {
+ I2CSlave i2c;
+
+ uint8_t config;
+ uint8_t interrupt_mask;
+ uint8_t conversion_rate;
+ uint8_t channel_disable;
+ bool deep_shutdown;
+ uint8_t advanced_config;
+
+ /* channel reading registers, 2 bytes each */
+ uint16_t channels[ADC128D818_NUM_CHANNELS];
+
+ /* high and low limit registers 0x2a - 0x39, one byte each */
+ uint8_t limit[ADC128D818_NUM_CHANNELS * 2];
+
+ /* input buffer */
+ uint8_t len;
+ uint8_t buf[2];
+
+ /* output buffer */
+ uint8_t outlen;
+ uint8_t outbuf[2];
+
+ /* selected channel for read/write operation */
+ uint8_t pointer;
+};
+
+struct ADC128D818Class {
+ I2CSlaveClass parent_class;
+};
+
+OBJECT_DECLARE_TYPE(ADC128D818State, ADC128D818Class, ADC128D818)
+
+static void adc128d818_read(ADC128D818State *s)
+{
+ uint8_t ch_num = 0;
+ switch (s->pointer) {
+ case REG_CONFIG:
+ s->outbuf[0] = s->config;
+ break;
+ case REG_INTERRUPT_STATUS:
+ s->outbuf[0] = 0x0; /* POR State */
+ break;
+ case REG_INTERRUPT_MASK:
+ s->outbuf[0] = s->interrupt_mask;
+ break;
+ case REG_CONVERSION_RATE:
+ s->outbuf[0] = s->conversion_rate;
+ break;
+ case REG_CHANNEL_DISABLE:
+ s->outbuf[0] = s->channel_disable;
+ break;
+ case REG_ONE_SHOT:
+ /* not marked as readable */
+ qemu_log_mask(LOG_GUEST_ERROR, "%s: read of register 0x%02x\n",
+ __func__, s->pointer);
+ s->outbuf[0] = 0x0;
+ break;
+ case REG_DEEP_SHUTDOWN:
+ s->outbuf[0] = s->deep_shutdown ? 0x1 : 0x0;
+ break;
+ case REG_ADVANCED_CONFIG:
+ s->outbuf[0] = s->advanced_config & 0b111;
+ break;
+ case REG_BUSY_STATUS:
+ /* not implemented */
+ s->outbuf[0] = 0b00000010; /* POR State */
+ break;
+ case REG_CHANNEL_READING(0):
+ case REG_CHANNEL_READING(1):
+ case REG_CHANNEL_READING(2):
+ case REG_CHANNEL_READING(3):
+ case REG_CHANNEL_READING(4):
+ case REG_CHANNEL_READING(5):
+ case REG_CHANNEL_READING(6):
+ case REG_CHANNEL_READING(7):
+ ch_num = s->pointer - REG_CHANNEL_READING(0);
+ /* high byte comes first, driver reads swapped */
+ s->outbuf[0] = (s->channels[ch_num] >> 8) & 0xff;
+ s->outbuf[1] = s->channels[ch_num] & 0xff;
+ break;
+ case REG_LIMIT(0):
+ case REG_LIMIT(1):
+ case REG_LIMIT(2):
+ case REG_LIMIT(3):
+ case REG_LIMIT(4):
+ case REG_LIMIT(5):
+ case REG_LIMIT(6):
+ case REG_LIMIT(7):
+ case REG_LIMIT(8):
+ case REG_LIMIT(9):
+ case REG_LIMIT(10):
+ case REG_LIMIT(11):
+ case REG_LIMIT(12):
+ case REG_LIMIT(13):
+ case REG_LIMIT(14):
+ case REG_LIMIT(15):
+ s->outbuf[0] = s->limit[s->pointer - REG_LIMIT(0)];
+ break;
+ case REG_MANUFACTURER_ID:
+ s->outbuf[0] = 0x1; /* readonly */
+ break;
+ case REG_REVISION_ID:
+ s->outbuf[0] = 0b00001001; /* readonly */
+ break;
+ default:
+ qemu_log_mask(LOG_GUEST_ERROR, "%s: read of register 0x%02x\n",
+ __func__, s->pointer);
+ break;
+ }
+}
+
+static void adc128d818_write_advanced_config(ADC128D818State *s, uint8_t data)
+{
+ /*
+ * Note: Whenever the Advanced Configuration Register is programmed,
+ * all of the values in the Channel Reading Registers and
+ * Interrupt Status Registers will return to their default values.
+ */
+
+ s->advanced_config = (data & 0b111);
+}
+
+static void adc128d818_write(ADC128D818State *s, uint8_t data)
+{
+ trace_adc128d818_write(s->i2c.address, s->pointer, data);
+
+ /* which bits in config register are writable */
+ const uint8_t config_w_mask = 0b10001011;
+ const uint8_t config_ro_mask = (uint8_t)~config_w_mask;
+
+ switch (s->pointer) {
+ case REG_CONFIG:
+ s->config = (s->config & config_ro_mask) | (data & config_w_mask);
+ break;
+ case REG_INTERRUPT_MASK:
+ s->interrupt_mask = data;
+ break;
+ case REG_CONVERSION_RATE:
+ s->conversion_rate = data;
+ break;
+ case REG_CHANNEL_DISABLE:
+ s->channel_disable = data;
+ break;
+ case REG_ONE_SHOT:
+ /*
+ * Initiate a single conversion and comparison cycle when
+ * the device is in shutdown mode or deep shutdown mode, after
+ * which the device returns to the respective mode that it was in
+ *
+ */
+ break;
+ case REG_DEEP_SHUTDOWN:
+ s->deep_shutdown = (data & 0x1) != 0;
+ break;
+ case REG_ADVANCED_CONFIG:
+ adc128d818_write_advanced_config(s, data);
+ break;
+ case REG_LIMIT(0):
+ case REG_LIMIT(1):
+ case REG_LIMIT(2):
+ case REG_LIMIT(3):
+ case REG_LIMIT(4):
+ case REG_LIMIT(5):
+ case REG_LIMIT(6):
+ case REG_LIMIT(7):
+ case REG_LIMIT(8):
+ case REG_LIMIT(9):
+ case REG_LIMIT(10):
+ case REG_LIMIT(11):
+ case REG_LIMIT(12):
+ case REG_LIMIT(13):
+ case REG_LIMIT(14):
+ case REG_LIMIT(15):
+ s->limit[s->pointer - REG_LIMIT(0)] = data;
+ break;
+ default:
+ qemu_log_mask(LOG_GUEST_ERROR, "%s: write of register 0x%02x\n",
+ __func__, s->pointer);
+ break;
+ }
+}
+
+static int adc128d818_send(I2CSlave *i2c, uint8_t data)
+{
+ ADC128D818State *s = ADC128D818(i2c);
+ trace_adc128d818_send(s->i2c.address, data);
+
+ s->outlen = 0;
+ s->buf[s->len] = data;
+
+ if (s->len == 0) {
+ s->pointer = data;
+ } else if (s->len == 1) {
+ adc128d818_write(s, data);
+ }
+
+ s->len++;
+ return 0;
+}
+
+static uint8_t adc128d818_recv(I2CSlave *i2c)
+{
+ ADC128D818State *s = ADC128D818(i2c);
+ trace_adc128d818_recv(s->i2c.address, s->pointer);
+
+ adc128d818_read(s);
+
+ if (s->outlen >= 2) {
+ qemu_log_mask(LOG_GUEST_ERROR, "%s: too many bytes read\n", __func__);
+ s->outlen = 0;
+ }
+
+ const uint8_t data = s->outbuf[s->outlen++];
+
+ trace_adc128d818_recv_return(s->i2c.address, data);
+ return data;
+}
+
+static int adc128d818_event(I2CSlave *i2c, enum i2c_event event)
+{
+ ADC128D818State *s = ADC128D818(i2c);
+
+ trace_adc128d818_event(s->i2c.address, event);
+
+ switch (event) {
+ case I2C_START_RECV:
+ s->outlen = 0;
+ break;
+ case I2C_START_SEND:
+ s->len = 0;
+ break;
+ default:
+ break;
+ }
+
+ return 0;
+}
+
+static const VMStateDescription vmstate_adc128d818 = {
+ .name = TYPE_ADC128D818,
+ .version_id = 0,
+ .minimum_version_id = 0,
+ .fields =
+ (const VMStateField[]){
+ VMSTATE_UINT8(config, ADC128D818State),
+ VMSTATE_UINT8(interrupt_mask, ADC128D818State),
+ VMSTATE_UINT8(conversion_rate, ADC128D818State),
+ VMSTATE_UINT8(channel_disable, ADC128D818State),
+ VMSTATE_BOOL(deep_shutdown, ADC128D818State),
+ VMSTATE_UINT8(advanced_config, ADC128D818State),
+ VMSTATE_UINT16_ARRAY(channels, ADC128D818State,
+ ADC128D818_NUM_CHANNELS),
+ VMSTATE_UINT8_ARRAY(limit, ADC128D818State,
+ ADC128D818_NUM_CHANNELS * 2),
+ VMSTATE_UINT8(len, ADC128D818State),
+ VMSTATE_UINT8_ARRAY(buf, ADC128D818State, 2),
+ VMSTATE_UINT8(outlen, ADC128D818State),
+ VMSTATE_UINT8_ARRAY(outbuf, ADC128D818State, 2),
+ VMSTATE_UINT8(pointer, ADC128D818State),
+ VMSTATE_I2C_SLAVE(i2c, ADC128D818State), VMSTATE_END_OF_LIST() }
+};
+
+static void adc128d818_init(Object *obj) { /* Nothing to do */ }
+
+I2CSlave *adc128d818_init_with_values(I2CBus *bus, uint8_t address,
+ const uint16_t *init_values,
+ uint32_t init_values_size)
+{
+ ADC128D818State *s;
+
+ s = ADC128D818(i2c_slave_new(TYPE_ADC128D818, address));
+
+ for (int i = 0; i < ADC128D818_NUM_CHANNELS; i++) {
+
+ /* arbitrary value */
+ uint16_t value = 0b0000101011010010;
+
+ if (i < init_values_size) {
+ value = init_values[i];
+ }
+ s->channels[i] = value;
+ }
+
+ i2c_slave_realize_and_unref(I2C_SLAVE(s), bus, &error_abort);
+
+ return I2C_SLAVE(s);
+}
+
+static void adc128d818_reset(DeviceState *dev)
+{
+ ADC128D818State *s = ADC128D818(dev);
+
+ s->pointer = 0;
+ s->outlen = 0;
+
+ /* POR-State */
+ s->config = 0b00001000;
+ s->interrupt_mask = 0;
+ s->conversion_rate = 0;
+ s->channel_disable = 0;
+ s->deep_shutdown = 0;
+ s->advanced_config = 0;
+
+ /* No POR-State defined in datasheet */
+ for (int i = 0; i < ADC128D818_NUM_CHANNELS * 2; i++) {
+ s->limit[i] = 0;
+ }
+}
+
+static void adc128d818_realize(DeviceState *dev, Error **errp)
+{
+ ADC128D818State *s = ADC128D818(dev);
+
+ trace_adc128d818_realize(s->i2c.address);
+}
+
+static void adc128d818_class_init(ObjectClass *klass, const void *data)
+{
+ DeviceClass *dc = DEVICE_CLASS(klass);
+ I2CSlaveClass *k = I2C_SLAVE_CLASS(klass);
+
+ dc->realize = adc128d818_realize;
+ dc->desc = "Texas Instruments ADC128D818 12-bit ADC with temp sensor";
+ dc->vmsd = &vmstate_adc128d818;
+ dc->legacy_reset = adc128d818_reset;
+ k->event = adc128d818_event;
+ k->recv = adc128d818_recv;
+ k->send = adc128d818_send;
+}
+
+static const TypeInfo adc128d818_info = {
+ .name = TYPE_ADC128D818,
+ .parent = TYPE_I2C_SLAVE,
+ .instance_size = sizeof(ADC128D818State),
+ .class_size = sizeof(ADC128D818Class),
+ .instance_init = adc128d818_init,
+ .class_init = adc128d818_class_init,
+};
+
+static void adc128d818_register_types(void)
+{
+ type_register_static(&adc128d818_info);
+}
+
+type_init(adc128d818_register_types)
diff --git a/hw/arm/Kconfig b/hw/arm/Kconfig
index 76a7d327a9..cc89c65e3f 100644
--- a/hw/arm/Kconfig
+++ b/hw/arm/Kconfig
@@ -554,6 +554,7 @@ config ASPEED_SOC
select MAX31785
select MAX31790
select MAX11615
+ select ADC128D818
select FSI_APB2OPB_ASPEED
select AT24C
select PCI_EXPRESS
diff --git a/hw/sensor/Kconfig b/hw/sensor/Kconfig
index 84eede9d84..c9190ff780 100644
--- a/hw/sensor/Kconfig
+++ b/hw/sensor/Kconfig
@@ -51,3 +51,7 @@ config MAX31790
config MAX11615
bool
depends on I2C
+
+config ADC128D818
+ bool
+ depends on I2C
diff --git a/hw/sensor/meson.build b/hw/sensor/meson.build
index a1e26604fa..defd7647e7 100644
--- a/hw/sensor/meson.build
+++ b/hw/sensor/meson.build
@@ -10,3 +10,4 @@ system_ss.add(when: 'CONFIG_ISL_PMBUS_VR', if_true:
files('isl_pmbus_vr.c'))
system_ss.add(when: 'CONFIG_MAX31785', if_true: files('max31785.c'))
system_ss.add(when: 'CONFIG_MAX31790', if_true: files('max31790.c'))
system_ss.add(when: 'CONFIG_MAX11615', if_true: files('max11615.c'))
+system_ss.add(when: 'CONFIG_ADC128D818', if_true: files('adc128d818.c'))
diff --git a/hw/sensor/trace-events b/hw/sensor/trace-events
index 3fed979e85..4853f1944d 100644
--- a/hw/sensor/trace-events
+++ b/hw/sensor/trace-events
@@ -20,3 +20,11 @@ max11615_recv(uint8_t i2c_addr, uint8_t reg_addr) "i2c_addr:
0x%02x, reg_addr: 0
max11615_recv_return(uint8_t i2c_addr, uint8_t data) "i2c_addr: 0x%02x,
returns: 0x%02x"
max11615_event(uint8_t i2c_addr, uint8_t event) "i2c_addr: 0x%02x, event:
0x%02x"
max11615_realize(uint8_t i2c_addr) "i2c_addr: 0x%02x"
+
+# adc128d818.c
+adc128d818_send(uint8_t i2c_addr, uint8_t data) "i2c_addr: 0x%02x, data:
0x%02x"
+adc128d818_write(uint8_t i2c_addr, uint8_t reg, uint8_t data) "i2c_addr:
0x%02x, reg: 0x%02x data: 0x%02x"
+adc128d818_recv(uint8_t i2c_addr, uint8_t reg) "i2c_addr: 0x%02x, reg: 0x%02x"
+adc128d818_recv_return(uint8_t i2c_addr, uint8_t data) "i2c_addr: 0x%02x,
returns: 0x%02x"
+adc128d818_event(uint8_t i2c_addr, uint8_t event) "i2c_addr: 0x%02x, event:
0x%02x"
+adc128d818_realize(uint8_t i2c_addr) "i2c_addr: 0x%02x"
diff --git a/tests/functional/arm/test_aspeed_fby4.py
b/tests/functional/arm/test_aspeed_fby4.py
index 319f1a7672..883e058832 100755
--- a/tests/functional/arm/test_aspeed_fby4.py
+++ b/tests/functional/arm/test_aspeed_fby4.py
@@ -59,6 +59,16 @@ def do_test_arm_aspeed_openbmc_no_network(self, machine,
image, uboot,
exec_command_and_wait_for_pattern(self,
"cat /sys/bus/iio/devices/iio:device2/in_voltage_scale",
"0.500000000");
+ # ADC128D818 test
+ exec_command_and_wait_for_pattern(self,
+ "cat /sys/bus/i2c/devices/30-001f/hwmon/hwmon0/name",
"adc128d818");
+ exec_command_and_wait_for_pattern(self,
+ "cat /sys/bus/i2c/devices/30-001f/hwmon/hwmon0/in0_input", "75");
+ exec_command_and_wait_for_pattern(self,
+ "cat /sys/bus/i2c/devices/30-001f/hwmon/hwmon0/in0_min", "0");
+ exec_command_and_wait_for_pattern(self,
+ "cat /sys/bus/i2c/devices/30-001f/hwmon/hwmon0/in0_max", "0");
+
def test_arm_ast2600_yosemitev4_openbmc(self):
image_path = self.uncompress(self.ASSET_YOSEMITE_V4_FLASH)
--
2.54.0
