On Tue, Jul 14, 2026 at 07:45:47PM +0530, Aadeshveer Singh wrote: > Add documenatation for fast snapshot load covering an overview, the > architecture, usage and limitations. > > Signed-off-by: Aadeshveer Singh <[email protected]> > --- > docs/devel/migration/fast-snapshot-load.rst | 81 +++++++++++++++++++++ > docs/devel/migration/features.rst | 1 + > 2 files changed, 82 insertions(+) > create mode 100644 docs/devel/migration/fast-snapshot-load.rst > > diff --git a/docs/devel/migration/fast-snapshot-load.rst > b/docs/devel/migration/fast-snapshot-load.rst > new file mode 100644 > index 0000000000..0c0dc676fb > --- /dev/null > +++ b/docs/devel/migration/fast-snapshot-load.rst > @@ -0,0 +1,81 @@ > +================== > +Fast Snapshot Load > +================== > + > +Overview > +======== > +Fast snapshot load is an extension of the postcopy migration feature > +to disk loads. > + > +Unlike a usual snapshot load, which requires all VM data (RAM as well > +as device states) to be loaded into host RAM from the snapshot file > +for the guest to run, fast snapshot load uses postcopy infrastructure > +to load in only the required device states and load RAM pages on > +demand. The idea is to start the guest and serve its page faults on
Suggest to replace "load RAM pages on demand" to something more general, like, "allows the RAM pages to be loaded after VM starts". E.g. the eager load thread work isn't on-demand. > +the go, reducing the perceived resume time for large snapshots. > + > +Architecture > +============ > +This feature combines postcopy migration and mapped-ram capabilities > +to load RAM pages on demand. It is done by catching guest faults using > +Linux ``userfaultfd`` and loading the page by calculating the offset > +of its location in the snapshot file using mapped-ram capabilities. > + > +Fault Thread > +------------ > +The fault thread uses Linux ``userfaultfd`` to catch page faults caused > +by guest and directly load the page from the snapshot file. It is > +very similar to network postcopy fault thread, with primary difference > +being it loads pages directly by reading from the snapshot file. > + > +Eager Thread > +------------ > +Eager thread iterates over all pages in RAM and loads each page not > +yet loaded by fault thread. It is required as unlike network postcopy > +where majority of RAM has already been loaded via precopy, here entire > +RAM is waiting to be loaded. If there is no eager loading thread each > +page will only be loaded when it is required by guest. In case there > +are some background pages that are never/rarely accessed by guest, > +the system will be locked in migration state indefinitely. > + > +Synchronization > +--------------- > +In order to make sure both of these threads do not load the same page > +twice potentially overwriting and corrupting user RAM, a bitmap is > +used (``RAMBlock->pending_bmap``) which tracks the pages claimed to > +be loaded by threads. This prevents race condition when one thread > +is loading the page and other one tries to do the same. > + > +Usage > +===== > + > +Simply enable ``mapped-ram`` and ``postcopy-ram`` capabilities on > +the destination: > + > +.. code-block:: text > + > + migrate_set_capability mapped-ram on > + migrate_set_capability postcopy-ram on > + > +Use a ``file:`` URI for migration: > + > +.. code-block:: text > + > + migrate_incoming file:/path/to/snapshot/file > + > +Limitations > +=========== > + > + - Multifd > + Fast snapshot load is currently incompatible with ``multifd`` > + capability. While ``mapped-ram`` allows for parallel disk I/O, > + coupling it with ``postcopy`` capability requires additional > + infrastructure. > + > + - Host OS support > + Because this feautre essentially depends on ``userfaultfd`` > + to trap page faults, it is supported only on Linux hosts. > + > + - vhost-user > + Fast snapshot load does not currently support ``vhost-user`` > + backends. For this one you haven't added a check in the other patch to detect it happening, you can add one check to see if postcopy_notifier_list is empty: anything registered implies vhost-user enabled. Thanks, > diff --git a/docs/devel/migration/features.rst > b/docs/devel/migration/features.rst > index 9aef79e7fa..23c2a93173 100644 > --- a/docs/devel/migration/features.rst > +++ b/docs/devel/migration/features.rst > @@ -11,6 +11,7 @@ Migration has plenty of features to support different use > cases. > vfio > virtio > mapped-ram > + fast-snapshot-load > CPR > qpl-compression > uadk-compression > -- > 2.55.0 > -- Peter Xu
