On Fri, Jan 10, 2014 at 04:13:34PM +1100, Alexey Kardashevskiy wrote:
> On 01/08/2014 12:18 AM, Alexey Kardashevskiy wrote:
> > On 12/25/2013 02:43 AM, Michael S. Tsirkin wrote:
> >> On Wed, Dec 25, 2013 at 01:15:29AM +1100, Alexey Kardashevskiy wrote:
> >>> On 12/24/2013 08:40 PM, Michael S. Tsirkin wrote:
> >>>> On Tue, Dec 24, 2013 at 02:09:07PM +1100, Alexey Kardashevskiy wrote:
> >>>>> On 12/24/2013 03:24 AM, Michael S. Tsirkin wrote:
> >>>>>> On Mon, Dec 23, 2013 at 02:01:13AM +1100, Alexey Kardashevskiy wrote:
> >>>>>>> On 12/23/2013 01:46 AM, Alexey Kardashevskiy wrote:
> >>>>>>>> On 12/22/2013 09:56 PM, Michael S. Tsirkin wrote:
> >>>>>>>>> On Sun, Dec 22, 2013 at 02:01:23AM +1100, Alexey Kardashevskiy
> >>>>>>>>> wrote:
> >>>>>>>>>> Hi!
> >>>>>>>>>>
> >>>>>>>>>> I am having a problem with virtio-net + vhost on POWER7 machine -
> >>>>>>>>>> it does
> >>>>>>>>>> not survive reboot of the guest.
> >>>>>>>>>>
> >>>>>>>>>> Steps to reproduce:
> >>>>>>>>>> 1. boot the guest
> >>>>>>>>>> 2. configure eth0 and do ping - everything works
> >>>>>>>>>> 3. reboot the guest (i.e. type "reboot")
> >>>>>>>>>> 4. when it is booted, eth0 can be configured but will not work at
> >>>>>>>>>> all.
> >>>>>>>>>>
> >>>>>>>>>> The test is:
> >>>>>>>>>> ifconfig eth0 172.20.1.2 up
> >>>>>>>>>> ping 172.20.1.23
> >>>>>>>>>>
> >>>>>>>>>> If to run tcpdump on the host's "tap-id3" interface, it shows no
> >>>>>>>>>> trafic
> >>>>>>>>>> coming from the guest. If to compare how it works before and after
> >>>>>>>>>> reboot,
> >>>>>>>>>> I can see the guest doing an ARP request for 172.20.1.23 and
> >>>>>>>>>> receives the
> >>>>>>>>>> response and it does the same after reboot but the answer does not
> >>>>>>>>>> come.
> >>>>>>>>>
> >>>>>>>>> So you see the arp packet in guest but not in host?
> >>>>>>>>
> >>>>>>>> Yes.
> >>>>>>>>
> >>>>>>>>
> >>>>>>>>> One thing to try is to boot debug kernel - where pr_debug is
> >>>>>>>>> enabled - then you might see some errors in the kernel log.
> >>>>>>>>
> >>>>>>>> Tried and added lot more debug printk myself, not clear at all what
> >>>>>>>> is
> >>>>>>>> happening there.
> >>>>>>>>
> >>>>>>>> One more hint - if I boot the guest and the guest does not bring
> >>>>>>>> eth0 up
> >>>>>>>> AND wait more than 200 seconds (and less than 210 seconds), then
> >>>>>>>> eth0 will
> >>>>>>>> not work at all. I.e. this script produces not-working-eth0:
> >>>>>>>>
> >>>>>>>>
> >>>>>>>> ifconfig eth0 172.20.1.2 down
> >>>>>>>> sleep 210
> >>>>>>>> ifconfig eth0 172.20.1.2 up
> >>>>>>>> ping 172.20.1.23
> >>>>>>>>
> >>>>>>>> s/210/200/ - and it starts working. No reboot is required to
> >>>>>>>> reproduce.
> >>>>>>>>
> >>>>>>>> No "vhost" == always works. The only difference I can see here is
> >>>>>>>> vhost's
> >>>>>>>> thread which may get suspended if not used for a while after the
> >>>>>>>> start and
> >>>>>>>> does not wake up but this is almost a blind guess.
> >>>>>>>
> >>>>>>>
> >>>>>>> Yet another clue - this host kernel patch seems to help with the guest
> >>>>>>> reboot but does not help with the initial 210 seconds delay:
> >>>>>>>
> >>>>>>> diff --git a/drivers/vhost/vhost.c b/drivers/vhost/vhost.c
> >>>>>>> index 69068e0..5e67650 100644
> >>>>>>> --- a/drivers/vhost/vhost.c
> >>>>>>> +++ b/drivers/vhost/vhost.c
> >>>>>>> @@ -162,10 +162,10 @@ void vhost_work_queue(struct vhost_dev *dev,
> >>>>>>> struct
> >>>>>>> vhost_work *work)
> >>>>>>> list_add_tail(&work->node, &dev->work_list);
> >>>>>>> work->queue_seq++;
> >>>>>>> spin_unlock_irqrestore(&dev->work_lock, flags);
> >>>>>>> - wake_up_process(dev->worker);
> >>>>>>> } else {
> >>>>>>> spin_unlock_irqrestore(&dev->work_lock, flags);
> >>>>>>> }
> >>>>>>> + wake_up_process(dev->worker);
> >>>>>>> }
> >>>>>>> EXPORT_SYMBOL_GPL(vhost_work_queue);
> >>>>>>>
> >>>>>>>
> >>>>>>
> >>>>>> Interesting. Some kind of race? A missing memory barrier somewhere?
> >>>>>
> >>>>> I do not see how. I boot the guest and just wait 210 seconds, nothing
> >>>>> happens to cause races.
> >>>>>
> >>>>>
> >>>>>> Since it's all around startup,
> >>>>>> you can try kicking the host eventfd in
> >>>>>> vhost_net_start.
> >>>>>
> >>>>>
> >>>>> How exactly? This did not help. Thanks.
> >>>>>
> >>>>> diff --git a/hw/net/vhost_net.c b/hw/net/vhost_net.c
> >>>>> index 006576d..407ecf2 100644
> >>>>> --- a/hw/net/vhost_net.c
> >>>>> +++ b/hw/net/vhost_net.c
> >>>>> @@ -229,6 +229,17 @@ int vhost_net_start(VirtIODevice *dev,
> >>>>> NetClientState
> >>>>> *ncs,
> >>>>> if (r < 0) {
> >>>>> goto err;
> >>>>> }
> >>>>> +
> >>>>> + VHostNetState *vn = tap_get_vhost_net(ncs[i].peer);
> >>>>> + struct vhost_vring_file file = {
> >>>>> + .index = i
> >>>>> + };
> >>>>> + file.fd =
> >>>>> event_notifier_get_fd(virtio_queue_get_host_notifier(dev->vq));
> >>>>> + r = ioctl(vn->dev.control, VHOST_SET_VRING_KICK, &file);
> >>>>
> >>>> No, this sets the notifier, it does not kick.
> >>>> To kick you write 1 there:
> >>>> uint6_t v = 1;
> >>>> write(fd, &v, sizeof v);
> >>>
> >>>
> >>> Please, be precise. How/where do I get that @fd? Is what I do correct?
> >>
> >> Yes.
> >
> > Turns out that no. The control device in the host kernel does not implement
> > write() so it always fails.
> >
> > This works:
> >
> > uint64_t v = 1;
> > int fd = event_notifier_get_fd(&vq->host_notifier);
> > int r = write(fd, &v, sizeof v);
> >
> > By "works" I mean it helps to wake the whole thing up and the guest's eth0
> > starts working after 3 minutes delay.
>
>
>
> Checked if virtnet_napi_enable() is called as expected and it is. As I can
> see "Receiving skb proto" in the guest's receive_buf(), I believe
> host->guest channel works just fine but the guest is unable to send
> anything until QEMU writes to event notifier (the code above).
>
> I actually spotted the problem in the host kernel - KVM_IOEVENTFD is called
> with a PCI bus address but kvm_io_bus_write() is called with a guest
> physical address and these things are different on PPC64/spapr.
>
> I am trying to make a patch for this and post it to some list tonight, I'll
> put you in copy.
>
Can we fix this in qemu?
We do:
memory_region_add_eventfd(&proxy->bar, VIRTIO_PCI_QUEUE_NOTIFY, 2,
true, n, notifier);
I think as a result, KVM_IOEVENTFD should be called with guest physical address.
>
> >>> What
> >>> is uint6_t - uint8_t or uint16_t (neither works)?
> >>
> >> Sorry, should have been uint64_t.
> >>
> >>> May be it is a missing barrier - I rebooted machine several times and now
> >>> sometime after even 240 seconds (not 210 as before) it works (but most of
> >>> the time still does not)...
> >>>
> >>>
> >>>>> + if (r) {
> >>>>> + error_report("Error notifiyng host notifier: %d", -r);
> >>>>> + goto err;
> >>>>> + }
> >>>>> }
> >>>>>
> >>>>>
> >>>>>
> >>>>>>
> >>>>>>>
> >>>>>>>
> >>>>>>>>>> If to remove vhost=on, it is all good. If to try Fedora19
> >>>>>>>>>> (v3.10-something), it all good again - works before and after
> >>>>>>>>>> reboot.
> >>>>>>>>>>
> >>>>>>>>>>
> >>>>>>>>>> And there 2 questions:
> >>>>>>>>>>
> >>>>>>>>>> 1. does anybody have any clue what might go wrong after reboot?
> >>>>>>>>>>
> >>>>>>>>>> 2. Is there any good material to read about what exactly and how
> >>>>>>>>>> vhost
> >>>>>>>>>> accelerates?
> >>>>>>>>>>
> >>>>>>>>>> My understanding is that packets from the guest to the real
> >>>>>>>>>> network are
> >>>>>>>>>> going as:
> >>>>>>>>>> 1. guest's virtio-pci-net does ioport(VIRTIO_PCI_QUEUE_NOTIFY)
> >>>>>>>>>> 2. QEMU's net/virtio-net.c calls qemu_net_queue_deliver()
> >>>>>>>>>> 3. QEMU's net/tap.c calls tap_write_packet() and this is how the
> >>>>>>>>>> host knows
> >>>>>>>>>> that there is a new packet.
> >>>>>>>>
> >>>>>>>>
> >>>>>>>> What about the documentation? :) or the idea?
> >>>>>>>>
> >>>>>>>>
> >>>>>>>>>>
> >>>>>>>>>>
> >>>>>>>>>> Thanks!
> >>>>>>>>>>
> >>>>>>>>>>
> >>>>>>>>>> This how I run QEMU:
> >>>>>>>>>> ./qemu-system-ppc64 \
> >>>>>>>>>> -enable-kvm \
> >>>>>>>>>> -m 2048 \
> >>>>>>>>>> -machine pseries \
> >>>>>>>>>> -initrd 1.cpio \
> >>>>>>>>>> -kernel vml312_virtio_net_dbg \
> >>>>>>>>>> -nographic \
> >>>>>>>>>> -vga none \
> >>>>>>>>>> -netdev
> >>>>>>>>>> tap,id=id3,ifname=tap-id3,script=ifup.sh,downscript=ifdown.sh,vhost=on
> >>>>>>>>>> \
> >>>>>>>>>> -device virtio-net-pci,id=id4,netdev=id3,mac=C0:41:49:4b:00:00
> >>>>>>>>>>
> >>>>>>>>>>
> >>>>>>>>>> That is bridge config:
> >>>>>>>>>> [aik@dyn232 ~]$ brctl show
> >>>>>>>>>> bridge name bridge id STP enabled
> >>>>>>>>>> interfaces
> >>>>>>>>>> brtest 8000.00145e992e88 no pin eth4
> >>>>>>>>>>
> >>>>>>>>>>
> >>>>>>>>>> The ifup.sh script:
> >>>>>>>>>> ifconfig $1 hw ether ee:01:02:03:04:05
> >>>>>>>>>> /sbin/ifconfig $1 up
> >>>>>>>>>> /usr/sbin/brctl addif brtest $1
> >>>
> >>>
> >>>
> >>> --
> >>> Alexey
> >
> >
>
>
> --
> Alexey
