The reset width register controls how the pulse on the SoC's WDTRST{1,2} pins behaves. A pulse is emitted if the external reset bit is set in WDT_CTRL. WDT_RESET_WIDTH requires magic bit patterns to configure both push-pull/open-drain and active-high/active-low behaviours and thus needs some special handling in the write path.
Signed-off-by: Andrew Jeffery <and...@aj.id.au> --- I understand that we're in stabilisation mode, but I thought I'd send this out to provoke any feedback. Happy to resend after the 2.10 release if required. hw/watchdog/wdt_aspeed.c | 47 +++++++++++++++++++++++++++++++++++++---------- 1 file changed, 37 insertions(+), 10 deletions(-) diff --git a/hw/watchdog/wdt_aspeed.c b/hw/watchdog/wdt_aspeed.c index 8bbe579b6b66..4ef1412e99fc 100644 --- a/hw/watchdog/wdt_aspeed.c +++ b/hw/watchdog/wdt_aspeed.c @@ -14,10 +14,10 @@ #include "qemu/timer.h" #include "hw/watchdog/wdt_aspeed.h" -#define WDT_STATUS (0x00 / 4) -#define WDT_RELOAD_VALUE (0x04 / 4) -#define WDT_RESTART (0x08 / 4) -#define WDT_CTRL (0x0C / 4) +#define WDT_STATUS (0x00 / 4) +#define WDT_RELOAD_VALUE (0x04 / 4) +#define WDT_RESTART (0x08 / 4) +#define WDT_CTRL (0x0C / 4) #define WDT_CTRL_RESET_MODE_SOC (0x00 << 5) #define WDT_CTRL_RESET_MODE_FULL_CHIP (0x01 << 5) #define WDT_CTRL_1MHZ_CLK BIT(4) @@ -25,12 +25,21 @@ #define WDT_CTRL_WDT_INTR BIT(2) #define WDT_CTRL_RESET_SYSTEM BIT(1) #define WDT_CTRL_ENABLE BIT(0) +#define WDT_RESET_WIDTH (0x18 / 4) +#define WDT_RESET_WIDTH_ACTIVE_HIGH BIT(31) +#define WDT_POLARITY_MASK (0xFF << 24) +#define WDT_ACTIVE_HIGH_MAGIC (0xA5 << 24) +#define WDT_ACTIVE_LOW_MAGIC (0x5A << 24) +#define WDT_RESET_WIDTH_PUSH_PULL BIT(30) +#define WDT_DRIVE_TYPE_MASK (0xFF << 24) +#define WDT_PUSH_PULL_MAGIC (0xA8 << 24) +#define WDT_OPEN_DRAIN_MAGIC (0x8A << 24) +#define WDT_RESET_WIDTH_DURATION 0xFFF; -#define WDT_TIMEOUT_STATUS (0x10 / 4) -#define WDT_TIMEOUT_CLEAR (0x14 / 4) -#define WDT_RESET_WDITH (0x18 / 4) +#define WDT_TIMEOUT_STATUS (0x10 / 4) +#define WDT_TIMEOUT_CLEAR (0x14 / 4) -#define WDT_RESTART_MAGIC 0x4755 +#define WDT_RESTART_MAGIC 0x4755 static bool aspeed_wdt_is_enabled(const AspeedWDTState *s) { @@ -55,9 +64,10 @@ static uint64_t aspeed_wdt_read(void *opaque, hwaddr offset, unsigned size) return 0; case WDT_CTRL: return s->regs[WDT_CTRL]; + case WDT_RESET_WIDTH: + return s->regs[WDT_RESET_WIDTH]; case WDT_TIMEOUT_STATUS: case WDT_TIMEOUT_CLEAR: - case WDT_RESET_WDITH: qemu_log_mask(LOG_UNIMP, "%s: uninmplemented read at offset 0x%" HWADDR_PRIx "\n", __func__, offset); @@ -119,9 +129,25 @@ static void aspeed_wdt_write(void *opaque, hwaddr offset, uint64_t data, timer_del(s->timer); } break; + case WDT_RESET_WIDTH: + { + uint32_t property = data & WDT_POLARITY_MASK; + + if (property == WDT_ACTIVE_HIGH_MAGIC) { + s->regs[WDT_RESET_WIDTH] |= WDT_RESET_WIDTH_ACTIVE_HIGH; + } else if (property == WDT_ACTIVE_LOW_MAGIC) { + s->regs[WDT_RESET_WIDTH] &= ~WDT_RESET_WIDTH_ACTIVE_HIGH; + } else if (property == WDT_PUSH_PULL_MAGIC) { + s->regs[WDT_RESET_WIDTH] |= WDT_RESET_WIDTH_PUSH_PULL; + } else if (property == WDT_OPEN_DRAIN_MAGIC) { + s->regs[WDT_RESET_WIDTH] &= ~WDT_RESET_WIDTH_PUSH_PULL; + } + s->regs[WDT_RESET_WIDTH] &= ~WDT_RESET_WIDTH_DURATION; + s->regs[WDT_RESET_WIDTH] |= data & WDT_RESET_WIDTH_DURATION; + break; + } case WDT_TIMEOUT_STATUS: case WDT_TIMEOUT_CLEAR: - case WDT_RESET_WDITH: qemu_log_mask(LOG_UNIMP, "%s: uninmplemented write at offset 0x%" HWADDR_PRIx "\n", __func__, offset); @@ -167,6 +193,7 @@ static void aspeed_wdt_reset(DeviceState *dev) s->regs[WDT_RELOAD_VALUE] = 0x03EF1480; s->regs[WDT_RESTART] = 0; s->regs[WDT_CTRL] = 0; + s->regs[WDT_RESET_WIDTH] = 0XFF; timer_del(s->timer); } -- 2.11.0