v5 -> v6
- Remove zoned state persistence code. Replace position-independent
zone lists with QTAILQs.
- Close all open zones upon clearing of the controller. This is
a similar procedure to the one previously performed upon powering
up with zone persistence.
- Squash NS Types and ZNS triplets of commits to keep definitions
and trace event definitions together with the implementation code.
- Move namespace UUID generation to a separate patch. Add the new
"uuid" property as suggested by Klaus.
- Rework Commands and Effects patch to make sure that the log is
always in sync with the actual set of commands supported.
- Add two refactoring commits at the end of the series to
optimize read and write i/o path.
- Incorporate feedback from Keith, Klaus and Niklas:
* fix rebase errors in nvme_identify_ns_descr_list()
* remove unnecessary code from nvme_write_bar()
* move csi to NvmeNamespace and use it from the beginning in NSTypes
patch
* change zone read processing to cover all corner cases with RAZB=1
* sync w_ptr and d.wp in case of a i/o error at the preceding zone
* reword the commit message in active/inactive patch with the new
text from Niklas
* correct dlfeat reporting depending on the fill pattern set
* add more checks for "attached" n/s parameter to prevent i/o and
get/set features on inactive namespaces
* Use DEFINE_PROP_SIZE and DEFINE_PROP_SIZE32 for zone size/capacity
and ZASL respectively
* Improve zone size and capacity validation
* Correctly report NSZE
v4 -> v5
- Rebase to the current qemu-nvme.
- Use HostMemoryBackendFile as the backing storage for persistent
zone metadata.
- Fix the issue with filling the valid data in the next zone if RAZBi
is enabled.
v3 -> v4
- Fix bugs introduced in v2/v3 for QD > 1 operation. Now, all writes
to a zone happen at the new write pointer variable, zone->w_ptr,
that is advanced right after submitting the backend i/o. The existing
zone->d.wp variable is updated upon the successful write completion
and it is used for zone reporting. Some code has been split from
nvme_finalize_zoned_write() function to a new function,
nvme_advance_zone_wp().
- Make the code compile under mingw. Switch to using QEMU API for
mmap/msync, i.e. memory_region...(). Since mmap is not available in
mingw (even though there is mman-win32 library available on Github),
conditional compilation is added around these calls to avoid
undefined symbols under mingw. A better fix would be to add stub
functions to softmmu/memory.c for the case when CONFIG_POSIX is not
defined, but such change is beyond the scope of this patchset and it
can be made in a separate patch.
- Correct permission mask used to open zone metadata file.
- Fold "Define 64 bit cqe.result" patch into ZNS commit.
- Use clz64/clz32 instead of defining nvme_ilog2() function.
- Simplify rpt_empty_id_struct() code, move nvme_fill_data() back
to ZNS patch.
- Fix a power-on processing bug.
- Rename NVME_CMD_ZONE_APND to NVME_CMD_ZONE_APPEND.
- Make the list of review comments addressed in v2 of the series
(see below).
v2 -> v3:
- Moved nvme_fill_data() function to the NSTypes patch as it is
now used there to output empty namespace identify structs.
- Fixed typo in Maxim's email address.
v1 -> v2:
- Rebased on top of qemu-nvme/next branch.
- Incorporated feedback from Klaus and Alistair.
* Allow a subset of CSE log to be read, not the entire log
* Assign admin command entries in CSE log to ACS fields
* Set LPA bit 1 to indicate support of CSE log page
* Rename CC.CSS value CSS_ALL_NSTYPES (110b) to CSS_CSI
* Move the code to assign lbaf.ds to a separate patch
* Remove the change in firmware revision
* Change "driver" to "device" in comments and annotations
* Rename ZAMDS to ZASL
* Correct a few format expressions and some wording in
trace event definitions
* Remove validation code to return NVME_CAP_EXCEEDED error
* Make ZASL to be equal to MDTS if "zone_append_size_limit"
module parameter is not set
* Clean up nvme_zoned_init_ctrl() to make size calculations
less confusing
* Avoid changing module parameters, use separate n/s variables
if additional calculations are necessary to convert parameters
to running values
* Use NVME_DEFAULT_ZONE_SIZE to assign the default zone size value
* Use default 0 for zone capacity meaning that zone capacity will
be equal to zone size by default
* Issue warnings if user MAR/MOR values are too large and have
to be adjusted
* Use unsigned values for MAR/MOR
- Dropped "Simulate Zone Active excursions" patch.
Excursion behavior may depend on the internal controller
architecture and therefore be vendor-specific.
- Dropped support for Zone Attributes and zoned AENs for now.
These features can be added in a future series.
- NS Types support is extended to handle active/inactive namespaces.
- Update the write pointer after backing storage I/O completion, not
before. This makes the emulation to run correctly in case of
backing device failures.
- Avoid division in the I/O path if the device zone size is
a power of two (the most common case). Zone index then can be
calculated by using bit shift.
- A few reported bugs have been fixed.
- Indentation in function definitions has been changed to make it
the same as the rest of the code.
Zoned Namespace (ZNS) Command Set is a newly introduced command set
published by the NVM Express, Inc. organization as TP 4053. The main
design goals of ZNS are to provide hardware designers the means to
reduce NVMe controller complexity and to allow achieving a better I/O
latency and throughput. SSDs that implement this interface are
commonly known as ZNS SSDs.
This command set is implementing a zoned storage model, similarly to
ZAC/ZBC. As such, there is already support in Linux, allowing one to
perform the majority of tasks needed for managing ZNS SSDs.
The Zoned Namespace Command Set relies on another TP, known as
Namespace Types (NVMe TP 4056), which introduces support for having
multiple command sets per namespace.
Both ZNS and Namespace Types specifications can be downloaded by
visiting the following link -
https://nvmexpress.org/wp-content/uploads/NVM-Express-1.4-Ratified-TPs.zip
This patch series adds Namespace Types support and zoned namespace
emulation capability to the existing NVMe PCI device.
Based-on: <20201013174826.ga1049...@dhcp-10-100-145-180.wdl.wdc.com>
Dmitry Fomichev (9):
hw/block/nvme: Add Commands Supported and Effects log
hw/block/nvme: Generate namespace UUIDs
hw/block/nvme: Support Zoned Namespace Command Set
hw/block/nvme: Introduce max active and open zone limits
hw/block/nvme: Support Zone Descriptor Extensions
hw/block/nvme: Add injection of Offline/Read-Only zones
hw/block/nvme: Document zoned parameters in usage text
hw/block/nvme: Separate read and write handlers
hw/block/nvme: Merge nvme_write_zeroes() with nvme_write()
Niklas Cassel (2):
hw/block/nvme: Add support for Namespace Types
hw/block/nvme: Support allocated CNS command variants
block/nvme.c | 2 +-
hw/block/nvme-ns.c | 295 ++++++++
hw/block/nvme-ns.h | 109 +++
hw/block/nvme.c | 1556 ++++++++++++++++++++++++++++++++++++++---
hw/block/nvme.h | 9 +
hw/block/trace-events | 36 +-
include/block/nvme.h | 201 +++++-
7 files changed, 2084 insertions(+), 124 deletions(-)
--
2.21.0
