Hi Francisco,
On Fri, Dec 11, 2020 at 11:16 PM Francisco Iglesias
<frasse.igles...@gmail.com> wrote:
>
> Hello Bin,
>
> On [2020 Dec 11] Fri 14:07:21, Bin Meng wrote:
> > Hi Francisco,
> >
> > On Fri, Dec 4, 2020 at 7:28 PM Francisco Iglesias
> > <frasse.igles...@gmail.com> wrote:
> > >
> > > Hello Bin,
> > >
> > > On [2020 Dec 04] Fri 18:52:50, Bin Meng wrote:
> > > > Hi Francisco,
> > > >
> > > > On Fri, Dec 4, 2020 at 6:46 PM Francisco Iglesias
> > > > <frasse.igles...@gmail.com> wrote:
> > > > >
> > > > > Hello Bin,
> > > > >
> > > > > On [2020 Dec 04] Fri 15:52:12, Bin Meng wrote:
> > > > > > Hi Francisco,
> > > > > >
> > > > > > On Thu, Dec 3, 2020 at 4:38 PM Francisco Iglesias
> > > > > > <frasse.igles...@gmail.com> wrote:
> > > > > > >
> > > > > > > Hi Bin and Alistair,
> > > > > > >
> > > > > > > On [2020 Dec 02] Wed 11:40:11, Alistair Francis wrote:
> > > > > > > > On Sun, Nov 29, 2020 at 6:55 PM Bin Meng <bmeng...@gmail.com>
> > > > > > > > wrote:
> > > > > > > > >
> > > > > > > > > From: Bin Meng <bin.m...@windriver.com>
> > > > > > > > >
> > > > > > > > > SST flashes require a dummy byte after the address bits.
> > > > > > > > >
> > > > > > > > > Signed-off-by: Bin Meng <bin.m...@windriver.com>
> > > > > > > >
> > > > > > > > I couldn't find a datasheet that says this... But the actual
> > > > > > > > code
> > > > > > > > change looks fine, so:
> > > > > > > >
> > > > > > > > Acked-by: Alistair Francis <alistair.fran...@wdc.com>
> > > > > > > >
> > > > > > > > Alistair
> > > > > > > >
> > > > > > > > > ---
> > > > > > > > >
> > > > > > > > > hw/block/m25p80.c | 3 +++
> > > > > > > > > 1 file changed, 3 insertions(+)
> > > > > > > > >
> > > > > > > > > diff --git a/hw/block/m25p80.c b/hw/block/m25p80.c
> > > > > > > > > index 483925f..9b36762 100644
> > > > > > > > > --- a/hw/block/m25p80.c
> > > > > > > > > +++ b/hw/block/m25p80.c
> > > > > > > > > @@ -825,6 +825,9 @@ static void decode_fast_read_cmd(Flash *s)
> > > > > > > > > s->needed_bytes = get_addr_length(s);
> > > > > > > > > switch (get_man(s)) {
> > > > > > > > > /* Dummy cycles - modeled with bytes writes instead of
> > > > > > > > > bits */
> > > > > > > > > + case MAN_SST:
> > > > > > > > > + s->needed_bytes += 1;
> > > > > > >
> > > > > > > 1 dummy clk cycle is modelled as 1 byte write (see the comment
> > > > > > > above), so 1
> > > > > > > dummy byte (8 dummy clk cycles) will need +8 above.
> > > > > >
> > > > > > I think you were confused by the WINBOND codes. The comments are
> > > > > > correct. It is modeled with bytes instead of bits, so we should +=1.
> > > > >
> > > > > What the comment says is (perhaps not superclear) that 1 dummy clock
> > > > > cycle
> > > > > is modeled as one 1 byte write into the flash (meaining that 8 byte
> > > > > writes
> > > > > are needed for 1 dummy byte). Perhaps it is easier to understand
> > > > > looking into how the controllers issue the command towards the flash
> > > > > model
> > > > > (for example the xilinx_spips), the start of the FAST_READ cmd is
> > > > > issued
> > > > > as writing the following into the flash: 1 byte (cmd), 3 bytes
> > > > > (address),
> > > > > 8 bytes (8 dummy cycles -> 1 dummy byte).
> > > > >
> > > >
> > > > My interpretation of the comments are opposite: one cycle is a bit,
> > > > but we are not using bits, instead we are using bytes.
> > >
> > > Yes, the mentioning of 'bits' in the comment makes it not very clear at
> > > first read.
> > > Maybe just bellow would have been better:
> > >
> > > /* Dummy clock cycles - modeled with bytes writes */
> > >
> > > >
> > > > Testing shows that +=1 is the correct way with the imx_spi controller,
> > > > and with my SiFive SPI model in my local tree (not upstreamed yet)
> > >
> > > Perhaps an option could be to look into how the aspeed_smc, xilinx_spips
> > > or the
> > > npcm7xx_fiu generate dummy clock cycles and see if a similar solution to
> > > one of
> > > those could work aswell for the imx_spi?
> > >
> >
> > Thanks for pointing this out. So there is some inconsistency among
> > different SPI controller modeling.
>
> I'm not sure I understand you correctly but the controllers supporting
> commands with dummy clock cycles can only do it following the modeled
> approach, so I would rather say it is pretty consistent across the
> controllers (not all controllers support these commands though).
I mean there are 2 approaches to emulate the dummy cycles for
different SPI controller models, yet we only have one m25p80 flash
model to work with both of them. Some controllers may choose 1 byte to
emulate 1 dummy clock cycle, but some others choose 1 bit to emulate 1
dummy cycle. This is inconsistent.
>
> >
> > Or maybe fixing aspeed_smc, xilinx_spips and npcm7xx_fiu to work like
> > imx_spi?
>
> For me I would say no to above (it makes more sense to let new controllers
> implement the currently modeled approach).
Yes, we can certainly make them consistent. But the question is which
one is the correct one? I tried to search in the doc but in vain.
>
> > Which one is the expected behavior for dummy cycles?
>
> Dummy clock cycles are modeled as 1 byte written to the flash per dummy clock
> cycle (expected behavior).
>
Like I mentioned before, 8 bytes to emulate 8 dummy clock cycles does
not work with current imx_spi model.
Regards,
Bin
