virtio-mem exposes a dynamic amount of memory within RAMBlocks by coordinating with the VM. Memory within a RAMBlock can either get plugged and consequently used by the VM, or unplugged and consequently no longer used by the VM. Logical unplug is realized by discarding the physical memory backing for virtual memory ranges, similar to memory ballooning.
However, important difference to virtio-balloon are: a) A virtio-mem device only operates on its assigned memory region / RAMBlock ("device memory") b) Initially, all device memory is logically unplugged c) Virtual machines will never accidentally reuse memory that is currently logically unplugged. The spec defines most accesses to unplugged memory as "undefined behavior" -- except reading unplugged memory, which is currently expected to work, but that will change in the future. d) The (un)plug granularity is in the range of megabytes -- "memory blocks" e) The state (plugged/unplugged) of a memory block is always known and properly tracked. Whenever memory blocks within the RAMBlock get (un)plugged, changes are communicated via the RamDiscardManager to other QEMU subsystems, most prominently vfio which updates the DMA mapping accordingly. "Unplugging" corresponds to "discarding" and "plugging" corresponds to "populating". While migrating (precopy/postcopy) that state of such memory blocks cannot change, as virtio-mem will reject any guest requests that would change the state of blocks with "busy". We don't want to migrate such logically unplugged memory, because it can result in an unintended memory consumption both, on the source (when reading memory from some memory backends) and on the destination (when writing memory). Further, migration time can be heavily reduced when skipping logically unplugged blocks and we avoid populating unnecessary page tables in Linux. Right now, virtio-mem reuses the free page hinting infrastructure during precopy to exclude all logically unplugged ("discarded") parts from the migration stream. However, there are some scenarios that are not handled properly and need fixing. Further, there are some ugly corner cases in postcopy code and background snapshotting code that similarly have to handle such special RAMBlocks. Let's reuse the RamDiscardManager infrastructure to essentially handle precopy, postcopy and background snapshots cleanly, which means: a) In precopy code, fixing up the initial dirty bitmaps (in the RAMBlock and e.g., KVM) to exclude discarded ranges. b) In postcopy code, placing a zeropage when requested to handle a page falling into a discarded range -- because the source will never send it. Further, fix up the dirty bitmap when overwriting it in recovery mode. c) In background snapshot code, never populating discarded ranges, not even with the shared zeropage, to avoid unintended memory consumption, especially in the future with hugetlb and shmem. Detail: When realizing a virtio-mem devices, it will register the RAM for migration via vmstate_register_ram(). Further, it will set itself as the RamDiscardManager for the corresponding memory region of the RAMBlock via memory_region_set_ram_discard_manager(). Last but not least, memory device code will actually map the memory region into guest physical address space. So migration code can always properly identify such RAMBlocks. Tested with precopy/postcopy on shmem, where even reading unpopulated memory ranges will populate actual memory and not the shared zeropage. Tested with background snapshots on anonymous memory, because other backends are not supported yet with upstream Linux. Idealy, this should all go via the migration tree. v2 -> v3: - "migration/ram: Don't passs RAMState to migration_clear_memory_region_dirty_bitmap_*()" -- Added to make the next patch easier to implement - "migration/ram: Handle RAMBlocks with a RamDiscardManager on the migration source" -- Fixup the dirty bitmaps only initially and during postcopy recovery, not after every bitmap sync. Also properly clear the dirty bitmaps e.g., in KVM. [Peter] - "migration/postcopy: Handle RAMBlocks with a RamDiscardManager on the destination" -- Take care of proper host-page alignment [Peter] v1 -> v2: - "migration/ram: Handle RAMBlocks with a RamDiscardManager on the migration source" -- Added a note how it interacts with the clear_bmap and what we might want to further optimize in the future when synchronizing bitmaps. Cc: "Michael S. Tsirkin" <m...@redhat.com> Cc: Paolo Bonzini <pbonz...@redhat.com> Cc: Juan Quintela <quint...@redhat.com> Cc: "Dr. David Alan Gilbert" <dgilb...@redhat.com> Cc: Eduardo Habkost <ehabk...@redhat.com> Cc: Peter Xu <pet...@redhat.com> Cc: Andrey Gruzdev <andrey.gruz...@virtuozzo.com> Cc: Marek Kedzierski <mkedz...@redhat.com> Cc: Wei Yang <richard.weiy...@linux.alibaba.com> Cc: teawater <teawat...@linux.alibaba.com> Cc: Alex Williamson <alex.william...@redhat.com> Cc: Pankaj Gupta <pankaj.gu...@cloud.ionos.com> David Hildenbrand (7): memory: Introduce replay_discarded callback for RamDiscardManager virtio-mem: Implement replay_discarded RamDiscardManager callback migration/ram: Don't passs RAMState to migration_clear_memory_region_dirty_bitmap_*() migration/ram: Handle RAMBlocks with a RamDiscardManager on the migration source virtio-mem: Drop precopy notifier migration/postcopy: Handle RAMBlocks with a RamDiscardManager on the destination migration/ram: Handle RAMBlocks with a RamDiscardManager on background snapshots hw/virtio/virtio-mem.c | 92 +++++++++++------- include/exec/memory.h | 21 +++++ include/hw/virtio/virtio-mem.h | 3 - migration/postcopy-ram.c | 31 +++++- migration/ram.c | 166 +++++++++++++++++++++++++++++---- migration/ram.h | 1 + softmmu/memory.c | 11 +++ 7 files changed, 267 insertions(+), 58 deletions(-) -- 2.31.1