Hello,
I am trying to get an Oncore GPS board to PPS a FreeBSD 8.3
installation. Originally I was using a Sure GPS board and now I want
the better Oncore board to be working. From the log output below I am
talking to the Oncore board but it is not in particular listening:
---< cut here >---
25 Aug 22:41:07 ntpd[22526]: ntpd [email protected] Mon Apr 22 18:07:31
UTC 2013 (1): Starting
25 Aug 22:41:07 ntpd[22526]: Command line: /usr/local/sbin/ntpd -c
/etc/ntp.conf -A -g -N -p /var/run/ntpd.pid -l /var/log/ntpd.log
25 Aug 22:41:07 ntpd[22527]: proto: precision = 1.955 usec (-19)
25 Aug 22:41:07 ntpd[22527]: Listen and drop on 0 v4wildcard 0.0.0.0:123
25 Aug 22:41:07 ntpd[22527]: Listen and drop on 1 v6wildcard [::]:123
25 Aug 22:41:07 ntpd[22527]: Listen normally on 2 re0 172.16.3.6:123
25 Aug 22:41:07 ntpd[22527]: Listen normally on 3 lo0 [fe80::1%8]:123
25 Aug 22:41:07 ntpd[22527]: setsockopt IPV6_MULTICAST_IF 0 for
fe80::1%8 fails: Can't assign requested address
25 Aug 22:41:07 ntpd[22527]: Listen normally on 4 lo0 [::1]:123
25 Aug 22:41:07 ntpd[22527]: Listen normally on 5 lo0 127.0.0.1:123
25 Aug 22:41:07 ntpd[22527]: peers refreshed
25 Aug 22:41:07 ntpd[22527]: Listening on routing socket on fd #26 for
interface updates
25 Aug 22:52:51 ntpd[22527]: ntpd exiting on signal 15 (Terminated: 15)
25 Aug 22:52:51 ntpd[22819]: ntpd [email protected] Mon Apr 22 18:07:31
UTC 2013 (1): Starting
25 Aug 22:52:51 ntpd[22819]: Command line: /usr/local/sbin/ntpd -c
/etc/ntp.conf -A -g -N -p /var/run/ntpd.pid -l /var/log/ntpd.log
25 Aug 22:52:51 ntpd[22820]: proto: precision = 1.955 usec (-19)
25 Aug 22:52:51 ntpd[22820]: Listen and drop on 0 v4wildcard 0.0.0.0:123
25 Aug 22:52:51 ntpd[22820]: Listen and drop on 1 v6wildcard [::]:123
25 Aug 22:52:51 ntpd[22820]: Listen normally on 2 re0 172.16.3.6:123
25 Aug 22:52:51 ntpd[22820]: Listen normally on 3 lo0 [fe80::1%8]:123
25 Aug 22:52:51 ntpd[22820]: setsockopt IPV6_MULTICAST_IF 0 for
fe80::1%8 fails: Can't assign requested address
25 Aug 22:52:51 ntpd[22820]: Listen normally on 4 lo0 [::1]:123
25 Aug 22:52:51 ntpd[22820]: Listen normally on 5 lo0 127.0.0.1:123
25 Aug 22:52:51 ntpd[22820]: peers refreshed
25 Aug 22:52:51 ntpd[22820]: Listening on routing socket on fd #26 for
interface updates
25 Aug 22:52:51 ntpd[22820]: ONCORE[0]: ONCORE DRIVER -- CONFIGURING
25 Aug 22:52:51 ntpd[22820]: ONCORE[0]: state = ONCORE_NO_IDEA
25 Aug 22:52:51 ntpd[22820]: ONCORE[0]: Input mode = 2
25 Aug 22:52:51 ntpd[22820]: ONCORE[0]: Initializing timing to Assert.
25 Aug 22:52:51 ntpd[22820]: ONCORE[0]: HARDPPS Set.
25 Aug 22:52:51 ntpd[22820]: ONCORE[0]: SHMEM (size = 3628) is
CONFIGURED and available as /var/log/ntpstats/oncore.0
25 Aug 22:52:51 ntpd[22820]: ONCORE[0]: state = ONCORE_CHECK_ID
25 Aug 22:52:52 ntpd[22820]: ONCORE[0]: Oncore: Resend @@Cj
25 Aug 22:52:52 ntpd[22820]: ONCORE[0]: @@Cj
25 Aug 22:52:52 ntpd[22820]: ONCORE[0]: COPYRIGHT 1991-1997 MOTOROLA INC.
25 Aug 22:52:52 ntpd[22820]: ONCORE[0]: SFTW P/N # 98-P36848P
25 Aug 22:52:52 ntpd[22820]: ONCORE[0]: SOFTWARE VER # 2
25 Aug 22:52:52 ntpd[22820]: ONCORE[0]: SOFTWARE REV # 2
25 Aug 22:52:52 ntpd[22820]: ONCORE[0]: SOFTWARE DATE APR 24 1998
25 Aug 22:52:52 ntpd[22820]: ONCORE[0]: MODEL # R5122U1112
25 Aug 22:52:52 ntpd[22820]: ONCORE[0]: HWDR P/N # 5
25 Aug 22:52:52 ntpd[22820]: ONCORE[0]: SERIAL # R02YWM
25 Aug 22:52:52 ntpd[22820]: ONCORE[0]: MANUFACTUR DATE 8G25
25 Aug 22:52:52 ntpd[22820]: ONCORE[0]:
25 Aug 22:52:52 ntpd[22820]: ONCORE[0]: This looks like an Oncore UT
with version 2.2 firmware.
25 Aug 22:52:52 ntpd[22820]: ONCORE[0]: Channels = 8, TRAIM = ON
25 Aug 22:52:52 ntpd[22820]: ONCORE[0]: state = ONCORE_CHECK_CHAN
25 Aug 22:52:57 ntpd[22820]: ONCORE[0]: Input says chan = -1
25 Aug 22:52:57 ntpd[22820]: ONCORE[0]: Model # says chan = 8
25 Aug 22:52:57 ntpd[22820]: ONCORE[0]: Testing says chan = 8
25 Aug 22:52:57 ntpd[22820]: ONCORE[0]: Using chan = 8
25 Aug 22:52:57 ntpd[22820]: ONCORE[0]: state = ONCORE_HAVE_CHAN
25 Aug 22:52:58 ntpd[22820]: ONCORE[0]: state = ONCORE_TEST_SENT
25 Aug 22:53:05 ntpd[22820]: ONCORE[0]: GPS antenna: OK
25 Aug 22:53:05 ntpd[22820]: ONCORE[0]: state = ONCORE_INIT
25 Aug 22:53:08 ntpd[22820]: ONCORE[0]: Setting Posn from input data
25 Aug 22:53:08 ntpd[22820]: ONCORE[0]: state = ONCORE_ALMANAC
25 Aug 22:53:10 ntpd[22820]: ONCORE[0]: Posn:
25 Aug 22:53:10 ntpd[22820]: ONCORE[0]: Lat = N 53.5666667deg, Long
= W 6.5333333deg, Alt = 34.00m (111.55ft) GPS
25 Aug 22:53:10 ntpd[22820]: ONCORE[0]: Lat = N 53deg 34.0000m, Long
= W 6deg 32.00000m, Alt = 34.00m ( 111.55ft) GPS
25 Aug 22:53:10 ntpd[22820]: ONCORE[0]: Lat = N 53deg 34m 0.00s, Long
= W 6deg 32m 0.00s, Alt = 34.00m ( 111.55ft) GPS
25 Aug 22:53:10 ntpd[22820]: ONCORE[0]: Cable delay is set to 25 ns
25 Aug 22:53:10 ntpd[22820]: ONCORE[0]: Satellite mask angle set to 0
degrees
25 Aug 22:53:12 ntpd[22820]: ONCORE[0]: Have now loaded an ALMANAC
25 Aug 22:53:12 ntpd[22820]: ONCORE[0]: state = ONCORE_RUN
25 Aug 22:53:12 ntpd[22820]: ONCORE[0]: SSstate = ONCORE_SS_TESTING
25 Aug 22:53:13 ntpd[22820]: ONCORE[0]: ONCORE: Detected TRAIM, TRAIM = ON
25 Aug 22:53:13 ntpd[22820]: ONCORE[0]: Input says TRAIM = 0
25 Aug 22:53:13 ntpd[22820]: ONCORE[0]: Model # says TRAIM = 1
25 Aug 22:53:13 ntpd[22820]: ONCORE[0]: Testing says TRAIM = 1
25 Aug 22:53:13 ntpd[22820]: ONCORE[0]: Using TRAIM = 0
25 Aug 22:53:13 ntpd[22820]: ONCORE[0]: Initiating hardware 3D site survey
25 Aug 22:53:13 ntpd[22820]: ONCORE[0]: SSstate = ONCORE_SS_HW
25 Aug 22:53:13 ntpd[22820]: ONCORE[0]: PPS Offset is set to 0 ns
25 Aug 22:53:13 ntpd[22820]: ONCORE[0]: Satellite mask angle is 0 degrees
25 Aug 22:53:19 ntpd[22820]: ONCORE[0]: ONCORE: oncore_get_timestamp,
error serial pps
25 Aug 22:53:19 ntpd[22820]: ONCORE[0]: ONCORE: oncore_get_timestamp,
error serial pps
25 Aug 22:53:20 ntpd[22820]: ONCORE[0]: ONCORE: oncore_get_timestamp,
error serial pps
25 Aug 22:53:21 ntpd[22820]: ONCORE[0]: ONCORE: oncore_get_timestamp,
error serial pps
---< cut here>---
..and the PPS signal is not being heard either, so it is appearing:
--< cut here>---
[root@jupiter /etc]# /usr/local/sbin/ntpq -c pe
remote refid st t when poll reach delay offset
jitter
==============================================================================
GPS_ONCORE(0) .PPS. 0 l - 16 0 0.000
0.000 0.000
*140.203.204.77 .GPS. 1 u 46 64 77 16.277 -1.471
1.582
+tbag.heanet.ie .PPS. 1 u 48 64 77 13.035 1.915
1.899
-ntp1.oma.be .PPS. 1 u 43 64 77 27.430 -5.331
1.903
-ntp2.oma.be .PPS. 1 u 47 64 77 33.628 -5.304
1.265
+ntp0.nl.uu.net .PPS. 1 u 52 64 77 29.299 -2.648
2.451
-ntp1.nl.uu.net .PPS. 1 u 44 64 77 32.761 -7.283
3.126
#ntp1.rrze.uni-e .DCFp. 1 u 47 64 77 48.859 -8.601
1.001
-ntp2.rrze.uni-e .PPS. 1 u 49 64 77 50.530 -7.398
1.175
-i2t15.i2t.ehu.e .GPS. 1 u 50 64 77 70.018 -2.440
1.139
-erquy.linocomm. .PPS. 1 u 47 64 77 49.030 -1.660
1.106
-timehost.lysato .GPS. 1 u 52 64 77 59.969 -6.593
2.673
#ntp2.sp.se .PPS. 1 u 41 64 77 55.668 1.770
30.233
[root@jupiter /etc]#
---< cut here>--
Can anyone explain to me what is going wrong? I have googled this error
for many times now and have not received an answer.
Thank you,
Ron
--
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.
_______________________________________________
questions mailing list
[email protected]
http://lists.ntp.org/listinfo/questions
