We had to find end caps for a ground mount that was used as part of an environmental learning center. I was able to get vinyl end caps that worked online from caplugs (http://www.caplugs.com/). A little silicone to seal the deal...
[Description: Description: Description: NYLElogo] Mark Richardson mrichard...@newyorklightenergy.com<mailto:mrichard...@newyorklightenergy.com> From: re-wrenches-boun...@lists.re-wrenches.org [mailto:re-wrenches-boun...@lists.re-wrenches.org] On Behalf Of hol...@sbcglobal.net Sent: Saturday, August 11, 2012 10:05 AM To: RE-wrenches Subject: Re: [RE-wrenches] Unirac SolarMount rail caps just throwing this out....aluminum angle attached to ends - run between rail ends (each pair)? aluminum flat bar? closes ends and gives a trimmed look? Maybe use 24 or 22ga stainless than can be bent to form an angle? ask client to cover material cost as that is "custom" work beyond typical scope of build. Holt E. Kelly Holtek Fireplace & Solar Products 500 Jewell Dr. Waco TX. 76712 254-751-9111 www.holteksolar.com<http://www.holteksolar.com> ----- Original Message ----- From: Maverick Brown [Maverick Solar]<mailto:maver...@mavericksolar.com> To: 'RE-wrenches'<mailto:re-wrenches@lists.re-wrenches.org> Sent: Friday, August 10, 2012 6:56 PM Subject: Re: [RE-wrenches] Unirac SolarMount rail caps For the Bee's sake, just pump some grey silicone caulk into the ends and scrape flat. ?? From: re-wrenches-boun...@lists.re-wrenches.org<mailto:re-wrenches-boun...@lists.re-wrenches.org> [mailto:re-wrenches-boun...@lists.re-wrenches.org]<mailto:[mailto:re-wrenches-boun...@lists.re-wrenches.org]> On Behalf Of Dana Brandt Sent: Friday, August 10, 2012 3:12 PM To: RE-wrenches Subject: [RE-wrenches] Unirac SolarMount rail caps We just finished installing a system on SolarMount and the client is unhappy with how the ends of the SolarMount rail look. She says it looks unfinished and is concerned about bees nesting in them. I know there are other rail products with more finished looking ends but this system is already fully installed. Unirac has endcaps for the SunFrame, but those aren't compatible with SolarMount. Anyone run into this before? Thoughts on solutions? Thanks, Dana Dana Brandt Ecotech Energy Systems, LLC www.ecotechenergy.com<http://www.ecotechenergy.com> d...@ecotechenergy.com<mailto:d...@ecotechenergy.com> 360.318.7646 ________________________________ _______________________________________________ List sponsored by Home Power magazine List Address: RE-wrenches@lists.re-wrenches.org<mailto:RE-wrenches@lists.re-wrenches.org> Options & settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org List rules & etiquette: www.re-wrenches.org/etiquette.htm<http://www.re-wrenches.org/etiquette.htm> Check out participant bios: www.members.re-wrenches.org<http://www.members.re-wrenches.org>
<<inline: image001.jpg>>
_______________________________________________ List sponsored by Home Power magazine List Address: RE-wrenches@lists.re-wrenches.org Options & settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org List rules & etiquette: www.re-wrenches.org/etiquette.htm Check out participant bios: www.members.re-wrenches.org
