Kurt,
Less messy, yes; less tedious, maybe: anti-seize also comes in a semi-solid stick form, like a large lip balm tube with a cap and a twist dial on the bottom to raise the level of the anti-seize as it's used. One quick rub on the threads per bolt. Purchased through Fastenal.
Allan

Allan Sindelar
al...@sindelarsolar.com
NABCEP Certified PV Installation Professional
NABCEP Certified Technical Sales Professional
New Mexico EE98J Journeyman Electrician
Founder (Retired), Positive Energy, Inc.
505 780-2738 cell

 

On 6/29/2015 11:05 AM, Kurt Johnsen wrote:
Esteemed Wrenches,
Does anyone know of a less tedious and messy way to lube the bolts than squeeze tube anti-seize?

My 2 cents; I believe that the torque specs for an engineered assembly are put in there for a reason. Ignoring them puts the installer on the hook for any failures. Aside from being the right thing to do, using torque wrenches helps avoid assuming unnecessary financial risk which my thin margins cannot afford.

Kurt Johnsen

On Sun, Jun 28, 2015 at 5:27 PM, Ray Walters <r...@solarray.com> wrote:
Besides your note that cordless impact drivers can over torque the clamps, also they spin the bolts too fast which can lead to spalling of the SS hardware.
We now hand torque those connects.  Finally, most torque specs are for lubricated bolts.  We use anti-seize on the threads before torquing.
Using a cordless impact driver and no lube can cause not only module damage but also clamp damage, and end up with clamps not actually securing the modules, because the bolts spalled out before fully clamping.
R.Ray Walters
CTO, Solarray, Inc
Nabcep Certified PV Installer, 
Licensed Master Electrician
Solar Design Engineer
303 505-8760
On 6/28/2015 3:06 PM, Benn Kilburn wrote:
Chris,
It sounds (to me) that you are describing the bonding "tooth" dug through the aluminum frame and into the glass? or at least compressed the frame enough to break the glass?  If that is the case then i'm betting that the clamp bolt was way over-torqued.

You need to check the recommended tightening torque for the module and for the racking system you are using.  For example, what we are using these days, Kinetic, the tightening torque for mid and end clamps is 12 ft-lb and here are some recommended clamping torques from some different module mfgrs....
Conergy 8 NM - 6 ft-lb
Hanwha 5 NM - 3.7 ft-lb
JA Solar 18-24 NM - 13-18 ft-lb
These likely vary based on the construction of the module frame.
I've also found that some module mfgrs do not list recommended tightening torques in their install manuals, so best to use discretion.

We had a module break after clamping it down.  The crew described it as 'putting the module in place, clamping it down and turning around to grab the next module and hearing a 'crack' followed by the crackling glass sound (if you have ever heard a module break, the crackling sound can last for a few minutes).  The break pattern in the glass seemed to focus on a particular mid clamp.  I used a torque wrench, set at around 10 ft-lb and checked all the mid-clamp bolts, increasing the torque setting by a few ft-lb each time until it finally turned a bolt instead of clicking.  I found that most of the bolts were close to 30 ft-lb and the one that appeared to break the glass was about 34 ft-lb.
Suffice to say, we were getting carried away with tightening using cordless impact drivers. 
At that point i and the rest of the crew started using the torque wrench as we were going along until we had a better feel for what was the proper torque.  (i've done this before, but it is something that needs to be self "re-calibrated" often. 


Benn Kilburn 
CSA Certified Solar Photovoltaic Systems Electrician, SkyFire Energy Inc
6706 – 82 Ave NW | Edmonton, AB | T6B 0E7
email facebook twitter linkedin google

SkyFire
                              Energy Logo_horizontal


On Thu, Jun 25, 2015 at 5:11 PM, Chris Worcester <ch...@solarwindworks.com> wrote:

Hi


                                  Jason,

Have you or others been using the new UniRac SM mid and end clamps with the integrated bonding yet? My concern is the “Stainless steel Midclamp points, 2 per module, pierce module frame anodization to bond module to module through clamp.”

We had an MSI Alpha + self-bonding midclamp shatter the glass on an LG 280 last fall, as the factory set point was sticking out too far, so as it was being tightened down, on top of the module the point dug through the module’s top frame hitting the glass, shattering it.

I do wonder if there are any issues with this “point” on the UniRac midclamps potential for doing the same damage?

 

Chris Worcester

Solar Wind Works

NABCEP Certified PV Installer

Office 530-582-4503

Cell 530-448-9692

Fax 530-582-4603

www.solarwindworks.com

ch...@solarwindworks.com

 

From: RE-wrenches [mailto:re-wrenches-boun...@lists.re-wrenches.org] On Behalf Of Jason Szumlanski
Sent: Thursday, June 25, 2015 1:13 PM
To: RE-wrenches
Subject: Re: [RE-wrenches] SnapNrack

 

That decision was based on our distribution network offering better pricing on Unirac, and engineers being comfortable with it. Now with the integrated grounding from Unirac, I can't see moving away from it again barring a significant cost benefit. It also stacks and stocks easier than the Ironridge rails.


 

 

On Wed, Jun 24, 2015 at 5:55 PM, Dana Brandt <d...@ecotechenergy.com> wrote:

Hi Jason,

We've used Unirac for years but have been contemplating Ironridge. I'm curious what your experience was and why you went back to Unirac?

Anyone else have input on best racking systems for flush-mounted residential systems on comp roof?

Thanks,


Dana

Dana Brandt
Ecotech Energy Systems, LLC
www.ecotechenergy.com
d...@ecotechenergy.com
360.318.7646

 

On Wed, Feb 5, 2014 at 12:09 PM, Jason Szumlanski <ja...@fafcosolar.com> wrote:

By Snap N Rack, you mean Sun Run...

 

 

I'm curious if these vertical integrators will still make their acquired brands available to small dealers through distribution. When SolarCity snatched up Zep, I had concerns about being able to service or add onto existing Zep systems we installed. That's definitely a concern going forward, and reason to perhaps stick with the most compatible racking solutions available. We used IronRidge for a while, which is largely compatible with Unirac, but now we're back on the Unirac bandwagon. 

 

Interesting times...

 

Jason Szumlanski

Fafco Solar

 

 

On Wed, Feb 5, 2014 at 12:45 PM, Max Balchowsky <m...@seesolar.com> wrote:

We have been using Snap N' Rack for a while, Have lots of installs in Hawaii - so far no problems, I like the convenience of the design for snapping in the slider nut in mid rail, and also the ability to install the panels flush with the end of the rails….

 

Max Balchowsky
Design Engineer
SEE Systems
1048 Irvine Ave Suite 217
Newport Beach, Ca. 92660
760-403-6810

"Building a Better Future For The Next Generation"

 


From: Allen Frishman <amfr...@aeonsolar.com>
To: RE-wrenches <re-wrenches@lists.re-wrenches.org>
Sent: Wednesday, February 5, 2014 6:17 AM
Subject: Re: [RE-wrenches] SnapNrack

 

I am curious about the mid clamps on the snapnrack.   The flange that rests on top of the solar panel frame is so small ~ 3/16".    Anyone experience any problems with these failing in a big storm?    With solar panel frames not being square it is nice to have a little extra to grab - I am always curious as to why these clips are made with such a small area to hold the panels down.   

 

All feedback on these clips is appreciated.

Al Frishman
AeonSolar

 

On Jun 1, 2013, at 10:41 AM, Max Balchowsky wrote:



Have installed last three systems (35Kw)with snap n rack.

love it....

 

Max Balchowsky
Design Engineer
SEE Systems

1048 Irvine Ave Suite 217
Newport Beach, Ca. 92660
760-403-6810

"Building a Better Future For The Next Generation"

 


From: Solarguy <nt...@1scom.net>
To: 'RE-wrenches' <re-wrenches@lists.re-wrenches.org>
Sent: Friday, May 31, 2013 10:11 PM
Subject: Re: [RE-wrenches] SnapNrack

 

The only complaint with the Snapnrack rails is the thin wall can easily be distorted. This will allow the nut to drop out of its groove. Love the universal end clamps but have learned to assemble every one to check for proper fit before getting on the roof.

Jim Duncan

-----Original Message-----
From: re-wrenches-boun...@lists.re-wrenches.org [mailto:re-wrenches-boun...@lists.re-wrenches.org] On Behalf Of Drake
Sent: Friday, May 31, 2013 7:32 PM

To: re-wrenches@lists.re-wrenches.org
Subject: [RE-wrenches] SnapNrack

 

Hello Wrenches,

 

How would you rate the SnapNrack mounting systems against Unirac and other mounting systems?

 

Thanks,

 

Drake

 

_______________________________________________

List sponsored by Home Power magazine

 

 

Change email address & settings:

 

 

List rules & etiquette:

 

Check out participant bios:


_______________________________________________
List sponsored by Home Power magazine

List Address: RE-wrenches@lists.re-wrenches.org

Change email address & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org

List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org

List rules & etiquette:
www.re-wrenches.org/etiquette.htm

Check out participant bios:
www.members.re-wrenches.org


Preferences

§

1

2

3

4

5

6

7

8

9

0

-

=

Backspace

Tab

q

w

e

r

t

y

u

i

o

p

[

]

Return

capslock

a

s

d

f

g

h

j

k

l

;

'

\

shift

`

z

x

c

v

b

n

m

,

.

/

shift

English

Deutsch

Español

Français

Italiano

Polski

Português

Русский

alt

alt

Preferences

_______________________________________________
List sponsored by Home Power magazine

List Address: RE-wrenches@lists.re-wrenches.org

Change email address & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org

List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org

List rules & etiquette:
www.re-wrenches.org/etiquette.htm

Check out participant bios:
www.members.re-wrenches.org

 


_______________________________________________
List sponsored by Home Power magazine

List Address: RE-wrenches@lists.re-wrenches.org

Change email address & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org

List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org

List rules & etiquette:
www.re-wrenches.org/etiquette.htm

Check out participant bios:
www.members.re-wrenches.org



_______________________________________________
List sponsored by Home Power magazine

List Address: RE-wrenches@lists.re-wrenches.org

Change email address & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org

List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org

List rules & etiquette:
www.re-wrenches.org/etiquette.htm

Check out participant bios:
www.members.re-wrenches.org

 


_______________________________________________
List sponsored by Home Power magazine

List Address: RE-wrenches@lists.re-wrenches.org

Change email address & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org

List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org

List rules & etiquette:
www.re-wrenches.org/etiquette.htm

Check out participant bios:
www.members.re-wrenches.org

 


_______________________________________________
List sponsored by Redwood Alliance

List Address: RE-wrenches@lists.re-wrenches.org

Change listserver email address & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org

List-Archive: http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html

List rules & etiquette:
www.re-wrenches.org/etiquette.htm

Check out or update participant bios:
www.members.re-wrenches.org

 


_______________________________________________
List sponsored by Redwood Alliance

List Address: RE-wrenches@lists.re-wrenches.org

Change listserver email address & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org

List-Archive: http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html

List rules & etiquette:
www.re-wrenches.org/etiquette.htm

Check out or update participant bios:
www.members.re-wrenches.org





_______________________________________________
List sponsored by Redwood Alliance

List Address: RE-wrenches@lists.re-wrenches.org

Change listserver email address & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org

List-Archive: http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html

List rules & etiquette:
www.re-wrenches.org/etiquette.htm

Check out or update participant bios:
www.members.re-wrenches.org



_______________________________________________
List sponsored by Redwood Alliance

List Address: RE-wrenches@lists.re-wrenches.org

Change listserver email address & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org

List-Archive: http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html

List rules & etiquette:
www.re-wrenches.org/etiquette.htm

Check out or update participant bios:
www.members.re-wrenches.org





_______________________________________________
List sponsored by Redwood Alliance

List Address: RE-wrenches@lists.re-wrenches.org

Change listserver email address & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org

List-Archive: http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html

List rules & etiquette:
www.re-wrenches.org/etiquette.htm

Check out or update participant bios:
www.members.re-wrenches.org


_______________________________________________
List sponsored by Redwood Alliance

List Address: RE-wrenches@lists.re-wrenches.org

Change listserver email address & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org

List-Archive: 
http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html

List rules & etiquette:
www.re-wrenches.org/etiquette.htm

Check out or update participant bios:
www.members.re-wrenches.org

Reply via email to