Can you be more specific about the fndc interface issues. What wasn't working and the fix is new M3s firmware yet to be released?
Thx Jay > On Sep 20, 2017, at 4:10 AM, <d...@foxfire-energy.com> > <d...@foxfire-energy.com> wrote: > > Seems earlier versions of the 3s had a glitch that didn't play nice with > FN-DC.. OB tech said a new version wasn't available till early Oct.. Still > had control from Optics RE but no local control.. > > Good Luck > > db > > > Dan Brown > Foxfire Energy Corp. > Renewable Energy Systems > (802)-483-2564 > www.Foxfire-Energy.com > NABCEP #092907-44 > > > -------- Original Message -------- > Subject: [RE-wrenches] OutBack Power MATE3 to MATE3S Upgrade > From: Matthew Sirum <matthewsi...@gmail.com> > Date: Wed, September 20, 2017 6:12 am > To: re-wrenches <re-wrenches@lists.re-wrenches.org> > > Greetings All, > > I'm preparing to replace an existing OutBack Power MATE3 System > Display/Controller with the new MATE3S. The system is a grid tied 5 > stack of Radian GS8048A Inverter/Chargers. I am interested to know if > any of you may have done this and if you encountered any issues or > have any insights to pass along. This system does have a generator > and uses the Advanced Generator Start (AGS) function to control > generator start/stop and battery charging while the generator is > running. I believe this is the only Display/Controller based function > the system is using, so it will likely need to be programed and setup > in the new MATE3S. I am hopeful that all other programing is stored > in the Radians and will not need to be reprogramed/entered to the new > MATE3S. The system is connected to OpticsRE (OutBack Power's system > monitoring website/service). I assume we may need to do some > programing from the new MATE3S and/or from the system's OpticsRE site > to enable communication since the new MATE3S may have a different IP > address, MAC Address, and etc than the MATE3 we are removing. > > We are hopeful the new MATE3S will allow the system to function better > with its OpticsRE site and not need to be reset every couple months. > > Please let me know if you have any experience or thoughts to offer. > > Have any of you installed and setup the new MATE3S? Any Issues, > insights, or comparisons to the MATE3 to report? > > Thank you! > > Best regards, > > ----MATT > > Matthew Sirum > P.O. Box 1227 > Greenfield, MA 01302-1227 USA > phone: +1.413.773.0611 > email: matthewsi...@gmail.com > _______________________________________________ > List sponsored by Redwood Alliance > > List Address: RE-wrenches@lists.re-wrenches.org > > Change listserver email address & settings: > http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org > > List-Archive: > http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html > > List rules & etiquette: > www.re-wrenches.org/etiquette.htm > > Check out or update participant bios: > www.members.re-wrenches.org > > _______________________________________________ > List s >
_______________________________________________ List sponsored by Redwood Alliance List Address: RE-wrenches@lists.re-wrenches.org Change listserver email address & settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org List-Archive: http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html List rules & etiquette: www.re-wrenches.org/etiquette.htm Check out or update participant bios: www.members.re-wrenches.org