Hi folks; Has anybody out there on the lunatic fringe been able to make the Intel AL440LX motherboard with the built in sound support work under RedHat Linux 5.0? The built in sound config stuff seems to conflict with the PNP stuff. The card *seems to be* being detected and configured correctly by isapnp. Any clues anybody? -Chris (P.S. here's my isapnp.conf if that helps) # Card 1: (serial identifier cb 80 86 00 01 30 00 a8 65) # YMH0030 Serial No -2138701823 [checksum cb] # Version 1.0, Vendor version 0.1 # ANSI string -->OPL3-SA3 Snd System <-- # # Logical device id YMH0021 # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE YMH0030/-2138701823 (LD 0 # Multiple choice time, choose one only ! # Start dependent functions: priority preferred # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0220 # IO base alignment 16 bytes # Number of IO addresses required: 16 # (IO 0 (BASE 0x0220)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0530 # Maximum IO base address 0x0530 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 1 (BASE 0x0530)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0388 # Maximum IO base address 0x0388 # IO base alignment 8 bytes # Number of IO addresses required: 8 (IO 2 (BASE 0x0388)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0330 # Maximum IO base address 0x0330 # IO base alignment 2 bytes # Number of IO addresses required: 2 # (IO 3 (BASE 0x0330)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0370 # Maximum IO base address 0x0370 # IO base alignment 2 bytes # Number of IO addresses required: 2 # (IO 4 (BASE 0x0370)) # IRQ 5. # High true, edge sensitive interrupt (INT 0 (IRQ 5 (MODE +E))) # First DMA channel 0. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed type F (DMA 0 (CHANNEL 0)) # Next DMA channel 1. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed type F # (DMA 1 (CHANNEL 1)) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0240 # Maximum IO base address 0x0240 # IO base alignment 16 bytes # Number of IO addresses required: 16 # (IO 0 (BASE 0x0240)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0e80 # Maximum IO base address 0x0e80 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 1 (BASE 0x0e80)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0388 # Maximum IO base address 0x0388 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 2 (BASE 0x0388)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0300 # Maximum IO base address 0x0300 # IO base alignment 2 bytes # Number of IO addresses required: 2 # (IO 3 (BASE 0x0300)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0100 # Maximum IO base address 0x0ffe # IO base alignment 2 bytes # Number of IO addresses required: 2 # (IO 4 (BASE 0x0100)) # IRQ 5, 7, 9, 10 or 11. # High true, edge sensitive interrupt # (INT 0 (IRQ 5 (MODE +E))) # First DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed type F # (DMA 0 (CHANNEL 0)) # Next DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed type F # (DMA 1 (CHANNEL 0)) # Start dependent functions: priority functional # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0280 # IO base alignment 16 bytes # Number of IO addresses required: 16 # (IO 0 (BASE 0x0220)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0530 # Maximum IO base address 0x0f48 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 1 (BASE 0x0530)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0388 # Maximum IO base address 0x03f8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 2 (BASE 0x0388)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0300 # Maximum IO base address 0x0334 # IO base alignment 2 bytes # Number of IO addresses required: 2 # (IO 3 (BASE 0x0300)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0100 # Maximum IO base address 0x0ffe # IO base alignment 2 bytes # Number of IO addresses required: 2 # (IO 4 (BASE 0x0100)) # IRQ 3, 5, 7, 9, 10 or 11. # High true, edge sensitive interrupt # (INT 0 (IRQ 3 (MODE +E))) # First DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed type F # (DMA 0 (CHANNEL 0)) # Next DMA channel 0, 1 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed type F # (DMA 1 (CHANNEL 0)) # End dependent functions # (ACT Y) )) # # Logical device id YMH0022 # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE YMH0030/-2138701823 (LD 1 # Compatible device id PNPb02f # Multiple choice time, choose one only ! # Start dependent functions: priority preferred # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0201 # Maximum IO base address 0x0201 # IO base alignment 1 bytes # Number of IO addresses required: 1 (IO 0 (BASE 0x0201)) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0201 # Maximum IO base address 0x0211 # IO base alignment 16 bytes # Number of IO addresses required: 1 # (IO 0 (BASE 0x0201)) # End dependent functions # (ACT Y) )) # End tag... Checksum 0x00 (OK) # Returns all cards to the "Wait for Key" state (WAITFORKEY) ______________________________________________________________________ Chris Patti [EMAIL PROTECTED] Systems Wrangler Central Services - Entropy Reduction Specialist At Large ---------------------------------------------------------------------- -- PLEASE read the Red Hat FAQ, Tips, Errata and the MAILING LIST ARCHIVES! http://www.redhat.com/RedHat-FAQ /RedHat-Errata /RedHat-Tips /mailing-lists To unsubscribe: mail [EMAIL PROTECTED] with "unsubscribe" as the Subject.
