Even if your netmask is wrong you should still be able to ping the gateway
since it is on the same segment. Did you try that? If that does not work, is
this for DSL or cable? Some ISP's require authentication (Point to Point
over Ethernet) and then encapsulate the traffic.
Hope this helps
Richard
-----Original Message-----
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]
Sent: Thursday, February 28, 2002 2:28 PM
To: [EMAIL PROTECTED]
Subject: Re: Ethernet help
It was suggested that I try changing netmask to 255.255.255.0. Nothing
changed.
DEVICE=eth0
ONBOOT=yes
BOOTPROTO=static
IPADDR= 66.134.88.36
NETMASK=255.255.255.0
GATEWAY= 66.134.88.33
I then tried /sbin/ifconfig and got the following:
eth0 Link encap:Ethernet HWaddr 00:E0:01:04:F7:AB
inet adr:66.134.88.36 Bcast:66.134.88.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:10 errors:0 dropped:0 overruns:10 carrier:0
collisions:0 txqueuelen:100
Interrupt:5 Base address:0xe400
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask 255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:11 errors:0 dropped:0 overruns:0 frame:0
TX packets:11 errors:0 dropped:0 overruns:10 carrier:0
collisions:0 txqueuelen:0
Here is /sbin/route:
Kernal IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
66.134.88.0 * 255.255.255.0 U 0 0 0 eth0
127.0.0.0 * 255.0.0.0 U 0 0 0 lo
default 66.134.88.33 0.0.0.0 UG 0 0 0 eth0
There is no firewall.
thanks in advance for any help
Linda
on 2/27/02 6:40 PM, Devon at [EMAIL PROTECTED] wrote:
> -----BEGIN PGP SIGNED MESSAGE-----
> Hash: SHA1
>
> On Wednesday 27 February 2002 07:09 pm, [EMAIL PROTECTED] wrote:
>> Is there any software out there that I can use to test to see whether
>> or not my ethernet card is actually working? I have a two port card.
>> Both lights work on the card but I can't get either port to work. Both
>> are configured as follows:
>> DEVICE=eth0
>> ONBOOT=yes
>> BOOTPROTO=static
>> IPADDR=xxx.xxx.xxx.xxx
>> NETMASK=255.255.255.248
>> GATEWAY= xxx.xxx.xxx.xxx
>>
>> I have stopped and restarted the machine. Both eth0 and eth1 start up
>> as "OK" on startup. Can't ping in, can't ping out.
>> What am I missing?
>
> You've replaced some of the info that might help solve this with
> xxx.xxx.xxx.xxx :)
>
> First, is that netmask correct?
> Do you have a firewall running that might be blocking pings?
> What is the output of the following commands:
> /sbin/ifconfig
> /sbin/route
>
> - -D
>
> - --
>
> pgp key: http://www.tuxfan.homeip.net:8080/pgpkey.txt
>
> - --
> -----BEGIN PGP SIGNATURE-----
> Version: GnuPG v1.0.6 (GNU/Linux)
> Comment: For info see http://www.gnupg.org
>
> iD8DBQE8fZiTeMAUbzJhSVcRAnpDAJ45QnmIiF3z09+tzYYPOXxjR+Ky8wCfcOac
> nw2f4+QE9VPd5oFgbMbkcfw=
> =W1ks
> -----END PGP SIGNATURE-----
>
>
>
> _______________________________________________
> Redhat-list mailing list
> [EMAIL PROTECTED]
> https://listman.redhat.com/mailman/listinfo/redhat-list
>
_______________________________________________
Redhat-list mailing list
[EMAIL PROTECTED]
https://listman.redhat.com/mailman/listinfo/redhat-list
_______________________________________________
Redhat-list mailing list
[EMAIL PROTECTED]
https://listman.redhat.com/mailman/listinfo/redhat-list