Supports 154 Subscribers 50 CTCSS and 104 DCS codes
Separate DCS and CTCSS Deviation Adjustments: No other panel gives
you independent deviation settings for CTCSS and DCS. Allows users
to determine all active users. By means of the front panel display,
all the active users in the system can be displayed.
Squelch Tail Elimination: Using DCS turn off code. CTCSS Trak: A
proprietary DSP engine gives CSI tone panels unbeatable sensitivity
and talk off rejection.
Built in Test mode for setup. Allows the technician to generate any
CTCSS or DCS from a telephone plugged in the back of the unit.
Front Panel Status Lamps. Indicates if the system is in programming
mode, if DTMF is being transmitted, if transmitter is on, if COS is
active, and more.
COS input with Polarity Select and Threshold Control Low Power
Mode for battery powered sites
Busts Stuck Mic Users: The TP-154 lets you determine who caused
intentional or accidental interference by maintaining a stuck mic
record. Permament Cross Tone: Using DTMF, a mobile can cross his
tone/code to any other tone/code for unusual communications
possibilities.
PER USER PROGRAMMABLE FEATURES
Courtesy Tone: Generates a Beep after the user unkeys the mobile.
Hang time: Amount of time the repeater will be active after the
subscriber ceases transmission from his mobile.
CTCSS/DCS During Hang Time: Gives the user the choice of generating
CTCSS or DCS during the hang time
Cross Tone: Allows the transmitting CTCSS/DCS to be different than
the received CTCSS/DCS
Barge In Control: Controls whether the subscriber can be barged in
by another subscriber with a different tone or code
CWID Sequence Characters: Allows each user to have a different call
sign.
User Enable: Enables or disables specific tones or codes for
repeater use Hog Penalty: Enables the system operator to control the
length of time the subscriber can access the repeater.
Reserve Tone: If a subscriber is turned off and reserve tone is
enabled, the repeater will come up, but no audio will pass. Beeps
indicate reserve tone is active.
GLOBAL PROGRAMMABLE FEATURES
Per User Programmable Features System Programmable Features
Squelch Tail Length: Allow the user to set the squelch tail for
those operators who like to hear a squelch tail after the mobile has
finished transmitting. User CWID Interval: Subscribers callsigns are
sent five seconds after picking up the system and then every "CWID
Interval" thereafter.
Anti-Kerchunking Time: If enabled, repeater will not hang unless
user keys down at least as long as the time set.
CWID Speed: Allows the user to select how fast the Morse Code is
sent.
CTCSS/DCS Hold Delay: Allows the repeater to remain active for the
specififed time even though the incoming CTCSS/DCS has been lost.
CWID Sequence Characters: Allows a callsign of up to ten characters
to be transmitted for the system CWID.
Stuck Mike Activity Timer: If the user keeps his mike pressed beyond
the specififed time, the transmitter will be turned off until the
Mike is released.
System CWID Interval: Determines how often the system will send its
callsign when the system is not in use.
DCS Encode Polarity: Allows the user to remotely program the
polarity of the DCS data being transmitted. COR or CTCSS/DCS
Operate: Allows the user to operate in a tone mode using CTCSS or
DCS or in a carrier mode where the tones or codes are not used.
DCS Decode Polarity: Allows the user to remotely program the
polarity of the DCS data being received. Response Delay to CD2:
Delays the data transpond to give the base radio time to return to
receive after transmitting a command
Hog Penalty Time: The amount of time the repeater will be disabled
for that user that exceeded his allocated time on the repeater.
Programming Mode Access Code: Code needed to enter the programming
mode locally or over the air.
Hog Idle Time: The amount of time the user must not use the repeater
to reset the hog monitor time. Courtesy Tone Delay: Delays courtesy
beep after mobile drops input carrier.
Hog Monitor Time: The maximum time the user can use the repeater
without incurring a hog penalty time. Carrier Drop Delay: Adjust how
long the transmitter will stay on after the CTCSS/DCS drops at the
end of hang time.
ELECTRICAL AND MECHANICAL SPECIFICATIONS
Audio InInput Level: 20mV pp to 2.0V pp Input impedance: 220K AC
coupled.
Audio OutOutput Level: 0-5V ppOutput Impedance: 1K AC coupled
DCS/CTCSS OutOutput Level: 0-5V ppOutput impedance: 5K AC coupled
PTT KeyingPolarity: NPN pull to ground. Current:
150mA max.
COS InInput Voltage: 0 - 12 VoltsImpedance: Greater than 100K
Mechanical
Height 1.75 inch
Width 19.0 inch
Depth 7.5 inch
Weight 4 LBS
contact me off the group if intrested....Bob [EMAIL PROTECTED]
I dont connect here all that much!!!
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/Repeater-Builder/
<*> To unsubscribe from this group, send an email to:
[EMAIL PROTECTED]
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
