Will the FCC certification of the transmitter need to be changed because of the additional circuitry?
Neil - WA6KLA Gary Laforce wrote: > > It is for a Commercial system. But I don't see what that has to do with > it. > > Gary LaForce > Chariton Valley TriStar Communications > Columbia Service Department Supervisor > 573.441.2224 Direct Shop line > 573.442.1147 Main Business Line > 573.449.8310 Shop Fax line > [EMAIL PROTECTED] > > -----Original Message----- > From: Repeater-Builder@yahoogroups.com > [mailto:[EMAIL PROTECTED] On Behalf Of Neil McKie > Sent: Thursday, May 26, 2005 4:40 PM > To: Repeater-Builder@yahoogroups.com > Subject: Re: [Repeater-Builder] LTR controller on a GE mastr II Help > please > > Is this for an amateur or commercial band system? > > Neil - WA6KLA > > Gary Laforce wrote: > > > > I'm trying to put an LTR controller on a GE Mastr II the controller > > is a Trident Raider the Mastr II is a PM unit and this is were the > > problem is as I understand it. The factory tech support said that I > > would have to mod the ICOM as to how the audio was put into it??? > > So if anyone has input please let me know. > > > > Gary LaForce > > Chariton Valley TriStar Communications > > Columbia Service Department Supervisor > > 573.441.2224 Direct Shop line > > 573.442.1147 Main Business Line > > 573.449.8310 Shop Fax line > > [EMAIL PROTECTED] > > > > -----Original Message----- > > From: Repeater-Builder@yahoogroups.com > > [mailto:[EMAIL PROTECTED] On Behalf Of skipp025 > > Sent: Thursday, May 26, 2005 10:22 AM > > To: Repeater-Builder@yahoogroups.com > > Subject: [Repeater-Builder] Re: hardline connector generated IMD > > > > Hi Eric, > > > > The real fly in the soup are the 7/8 and higher > > mechanical center pin connections and any place > > where scratches and grooves are made. > > > > In addition to grooves and scratches Metal > > Burs and stringer materials from previous installs > > have been traced back to PIM (intermod) at busy > > (high rf) radio sites. > > > > The brass or stainless brush cleaning does help > > quite a bit, although it doesn't address any > > previous mechanical made deep center pin grooves > > from causing grief. I use a small round stainless > > pipe cleaning brush in the tool box to clean up > > the inside of >7/8" hardline. > > > > Smaller 1/4, 3/8 & 1/2 solder connectors shouldn't > > be as troublesome. > > > > There appear to be a lot of unsuspecting ways to > > make a diode... > > > > cheers, > > skipp > > > > > Eric Lemmon <[EMAIL PROTECTED]> wrote: > > > Skipp, > > > > > > Verrry interesting! By curious coincidence, the > > > installation instructions for the new Andrew Heliax > > > connectors states that the connector must first be > > > tightened and then removed to inspect the flare > > > before re-tightening. I understand that the advice > > > against re-using connectors is probably directed > > > toward re-use of connectors that have been in > > > service for some time, but the distinction should > > > be made that merely tightening the connector once > > > does not necessarily preclude tightening it a second > > > time. (I, too, reuse expensive Heliax connectors!) > > > 73, Eric Lemmon WB6FLY > > > > > > Yahoo! Groups Links > > > > > > > > > > Yahoo! Groups Links > > > > > > > > > > > Yahoo! Groups Links > > > > > Yahoo! Groups Links > > > > Yahoo! Groups Links <*> To visit your group on the web, go to: http://groups.yahoo.com/group/Repeater-Builder/ <*> To unsubscribe from this group, send an email to: [EMAIL PROTECTED] <*> Your use of Yahoo! Groups is subject to: http://docs.yahoo.com/info/terms/
