I'm attempting to move a previously working Maxtronic SA-3340S
SCSI-to-SATA disk array from a Sun Sparc system to a RedHat 5.2 system
running on Dell 2950 hardware.

While I don't expect, of course, to get at the data on the array, I would
like to deploy it.

The Dell sees the array, and /var/log/messages reports:

May 29 08:40:35 s31e066 kernel: SCSI device sdb: 2925232128 512-byte hdwr
sectors (1497719 MB

May 29 08:40:35 s31e066 kernel: sdb: Write Protect is off

May 29 08:40:35 s31e066 kernel: SCSI device sdb: drive cache: write back

May 29 08:40:35 s31e066 kernel: SCSI device sdb: 2925232128 512-byte hdwr
sectors (1497719 MB)

May 29 08:40:35 s31e066 kernel: sdb: Write Protect is off

May 29 08:40:35 s31e066 kernel: SCSI device sdb: drive cache: write back

May 29 08:40:35 s31e066 kernel:  sdb: sdb1 sdb9

May 29 08:40:35 s31e066 kernel: sd 2:0:0:0: Attached scsi disk sdb

Despite the indication scsi disk sdb was "attached," and the presence of
sdb device files in /dev, the system reports:

# fdisk /dev/sdb

Unable to open /dev/sdb

There are extensive, repeated dmesg entries, however:

scsi2 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0
        <Adaptec 39320A Ultra320 SCSI adapter>
        aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 101-133Mhz, 512
SCBs

  Vendor:           Model:                   Rev: R0.0
  Type:   Direct-Access                      ANSI SCSI revision: 04
 target2:0:0: asynchronous
scsi2:A:0:0: Tagged Queuing enabled.  Depth 4
 target2:0:0: Beginning Domain Validation
 target2:0:0: wide asynchronous
 target2:0:0: FAST-160 WIDE SCSI 320.0 MB/s DT IU QAS RTI WRFLOW PCOMP
(6.25 ns,
offset 127)
scsi 2:0:0:0: Attempting to queue an ABORT message:CDB: 0x12 0x0 0x0 0x0
0x40 0x0
scsi2: At time of recovery, card was not paused
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi2: Dumping Card State at program address 0x24 Mode 0x22
Card was paused
[ lengthy hex messages elided ]
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
scsi2:0:0:0: Cmd aborted from QINFIFO
scsi 2:0:0:0: Attempting to queue an ABORT message:CDB: 0x0 0x0 0x0 0x0
0x0 0x0
-- 
Tim Evans, TKEvans.com, Inc.    |   5 Chestnut Court
UNIX System Admin Consulting    |   Owings Mills, MD 21117
http://www.tkevans.com/         |   443-394-3864
http://www.come-here.com/News/  |   [EMAIL PROTECTED]


_______________________________________________
rhelv5-list mailing list
[email protected]
https://www.redhat.com/mailman/listinfo/rhelv5-list

Reply via email to