Could it be as simple as a check in the "Show first 100" box when the
library window is open? That has gotten me before.
On Fri, Jun 12, 2020, 1:10 AM Gavin Stephens <ga...@stephens.net.nz> wrote:
> Hmm trips down memory lane.
>
> So I manually started importing everything through RDLibrary, about 400
> songs so far until 8am this morning. Switched it off, came back this
> afternoon switched it on, and RDLibrary only reports 100 songs in the
> library, but all 400 songs are in the var/snd folder. That was painful
> work gone.
>
> What on earth would have caused that? It was a straight forward install
> so I'm not sure what's gone wrong there.
>
>
> On 12/06/2020 8:44 am, Robert Jeffares wrote:
> > Morena Gavin.
> >
> > The install has probably defaulted to 48,000.
> >
> > look at rdadmin > system settings and see where it's at.
> >
> > On a new install it's no big deal but if you have a library you are
> > copying over it needs to be at the rate the library was created at.
> >
> > Mine happens to be 44100.
> >
> > That may explain audition rate being fast.
> >
> > take a look at /etc/asound.conf
> >
> > I have a V3 which needed to be told what rate it was running at
> > because the on board sound card was insisting on something else.
> >
> > pcm.rd0 {
> > type hw
> > card 0
> > rate 48000 <-- you can change this to suit
> > device 0
> > }
> > ctl.rd0 {
> > type hw
> > card 0
> > }
> >
> > In the Rivendell menu under configuration run rdalsaconfig which
> > should find your ASI card.
> >
> > cat /etc/asound.conf will tell you which one is rd0, 1 2 3 etc
> >
> > 098176358
> >
> > regards
> >
> > Robert Jeffares
> >
> >
> > On 12/06/20 6:11 am, Gavin Stephens wrote:
> >> Hi guys,
> >>
> >> Just a couple of quick questions. It's been almost a decade since I
> >> used RD and I'm retiring my old machine here and installing RD3. I've
> >> done it via the instructions on the Paravel website with CentOS7.
> >>
> >> I've ran in to a few small hick ups with audio. I've got an ASI5111
> >> Rev.F card in the machine, and ALSA also appears to be active and
> >> listing the onboard sound. The ASI shows up as Card 0, ALSA Card 1.
> >> I've tried to configure via RDAirPlay settings Card 0 for main output
> >> 1 as port 0, then tried to change main output 2 as port 1, but it
> >> won't have a bar of it. I've set the audition as Card 1 and the
> >> on-board plays this fine albeit at a fast pitch.
> >>
> >> When I run RDAirPlay and play the cart, it just hangs. I'm obviously
> >> missing a step getting the ASI adapter to work correctly. Is ALSA
> >> locking this card out or something? Also the fast pitch through the
> >> onboard, I'm guessing that is a wrong sample rate setting somewhere.
> >> My memory isn't what it used to be using RD and I've forgotten which
> >> files on the machine to find for setting the sample rate, and to make
> >> sure ALSA is not using the ASI card and locking RD out from it.
> >>
> >> Any pointers in the right direction would be much appreciated. I'm
> >> about to import in a lot of music from Simian, I've tried rdimport
> >> however it doesn't import both the title and artist by default so I'm
> >> gonna go through and copy and paste it all over the weekend.
> >>
> >> Cheers,
> >>
> >> Gavin.
> >>
> >> N.Z.
> >>
> >>
>
> --
> This email has been checked for viruses by Avast antivirus software.
> https://www.avast.com/antivirus
>
> _______________________________________________
> Rivendell-dev mailing list
> Rivendell-dev@lists.rivendellaudio.org
> http://caspian.paravelsystems.com/mailman/listinfo/rivendell-dev
>
_______________________________________________
Rivendell-dev mailing list
Rivendell-dev@lists.rivendellaudio.org
http://caspian.paravelsystems.com/mailman/listinfo/rivendell-dev
