"Proxmox VE does not write changes directly to /etc/network/interfaces.
Instead, we write into a temporary file called
/etc/network/interfaces.new, this way you can do many related changes at
once"
O mai fi rămas dintr-un motiv oarecare fișierul ăsta?
On 5/8/24 15:46, Paul Lacatus via RLUG wrote:
Era si o poza a interfetei WebUI dar care nu s-a dus pe lista.
On 08.05.2024 13:03, Alex 'CAVE' Cernat via RLUG wrote:
1. da-i un reboot daca nu i-ai dat, suna stupid, insa rezolva multe
(de la geam citire: for minor problems reboot, for major problems
reinstall ... din cand in cand e valabil si pentru pinguin)
2. te-ai jucat cu schimbatul placilor in ultimul timp? de l-o fi
vazut la un moment dat pe enp2 si apoi ai mutat in alt slot ?
Am dat nenumarate reset-rui iar cu jucatul cu placile , da, m-am jucat
pentru ca cea cu doua sfp+ nu se alinia bine in slotul PCIe. si am
incercat sa le rotesc intte slot-uri
3. nu mai stiu exact de unde determina proxmox care sunt placile de
retea (presupun ca te referi la $server$/system/network in gui), insa
am o vaga impresie ca se bazeaza pe /etc/network/interfaces, asa ca
as recomanda sa arunci un ochi si pe acolo, poate au ramas niste
gunoaie prin zona
cred ca au ramas in /etc/network/interfaces niste linii cu interfete
enp2 care nu mai apar in sistem,
Le-am sters si nu mai apar
binenteles, preferabil e sa fii fizic prin zona sau cumva sa mai ai
vreo modalitate de a intra pe server in caz de vreo gherla (ca deh,
se intampla si la case mai mari); deci, avand in vedere ca te joci cu
chestii foarte importante (si care-ti pot taia craca de sub
picioare), atunci atentie maxima
serverul (routerul) e in constructie, pe masa asa ca se poate
experimenta pe el .
Alex
ps: cum "simplicity is divine" (parca de la slack citire), intreb si
eu: nu-s totusi cam multe placi de retea pe acolo? :-D daca nu le
folosesti, mai scoate din ele :-P
Am nevoie de mai multe NIC , sunt trei WAN , unul pe sfp+, un lan pe
sfp+ si altele
On 08-May-24 11:49, Paul Lacatus via RLUG wrote:
Vreau sa fac un router ci opnSense sau pfSense virtualizat in
proxmox . Pe sistem am un NIC in placa de baza si apoi o placa Intel
cu 4 porturi de 1Gbps si o alta placa intel cu doua sfp+ de 10Gbps.
Daca intreb la Lspci apar corect
00:1f.5 Serial bus controller: Intel Corporation Cannon Lake PCH SPI
Controller (rev 10)
00:1f.6 Ethernet controller: Intel Corporation Ethernet Connection
(7) I219-LM (rev 10)
01:00.0 Ethernet controller: Intel Corporation Ethernet 10G 2P X520
Adapter (rev 01)
01:00.1 Ethernet controller: Intel Corporation Ethernet 10G 2P X520
Adapter (rev 01)
02:00.0 Non-Volatile memory controller: Samsung Electronics Co Ltd
NVMe SSD Controller SM981/PM981/PM983
03:00.0 Ethernet controller: Intel Corporation 82580 Gigabit Network
Connection (rev 01)
03:00.1 Ethernet controller: Intel Corporation 82580 Gigabit Network
Connection (rev 01)
03:00.2 Ethernet controller: Intel Corporation 82580 Gigabit Network
Connection (rev 01)
03:00.3 Ethernet controller: Intel Corporation 82580 Gigabit Network
Connection (rev 01)
la ip addr show e corect
ip addr show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host noprefixroute
valid_lft forever preferred_lft forever
2: enp3s0f0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
group default qlen 1000
link/ether 90:e2:ba:dc:85:d4 brd ff:ff:ff:ff:ff:ff
3: enp3s0f1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
group default qlen 1000
link/ether 90:e2:ba:dc:85:d5 brd ff:ff:ff:ff:ff:ff
4: eno1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
master vmbr0 state UP group default qlen 1000
link/ether 9c:7b:ef:3a:80:3a brd ff:ff:ff:ff:ff:ff
altname enp0s31f6
5: enp3s0f2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
group default qlen 1000
link/ether 90:e2:ba:dc:85:d6 brd ff:ff:ff:ff:ff:ff
6: enp3s0f3: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
group default qlen 1000
link/ether 90:e2:ba:dc:85:d7 brd ff:ff:ff:ff:ff:ff
7: enp1s0f0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
group default qlen 1000
link/ether a0:36:9f:cf:8f:64 brd ff:ff:ff:ff:ff:ff
8: enp1s0f1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN
group default qlen 1000
link/ether a0:36:9f:cf:8f:66 brd ff:ff:ff:ff:ff:ff
9: vmbr0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue
state UP group default qlen 1000
link/ether 9c:7b:ef:3a:80:3a brd ff:ff:ff:ff:ff:ff
inet 10.50.0.20/8 scope global vmbr0
valid_lft forever preferred_lft forever
inet6 fe80::9e7b:efff:fe3a:803a/64 scope link
valid_lft forever preferred_lft forever
dar in proxmox placa cu patru porturi apare dublata si pe enp2 si pe
enp3 . ce sa fac ?
Paul
_______________________________________________
RLUG mailing list
RLUG@lists.lug.ro
http://lists.lug.ro/mailman/listinfo/rlug_lists.lug.ro
_______________________________________________
RLUG mailing list
RLUG@lists.lug.ro
http://lists.lug.ro/mailman/listinfo/rlug_lists.lug.ro
_______________________________________________
RLUG mailing list
RLUG@lists.lug.ro
http://lists.lug.ro/mailman/listinfo/rlug_lists.lug.ro
_______________________________________________
RLUG mailing list
RLUG@lists.lug.ro
http://lists.lug.ro/mailman/listinfo/rlug_lists.lug.ro
