am instalat ieri un rh7.2 pe un calculator cu voodoo rush.
problema este ca n-am reusit sa fac sa mearga cum trebuie X-ul. monitorul
(un AOC 17" VLR) este detectat corect, rush-ul la fel (ca AT3D - este
chipul care se ocupa de 2D pe placa asta). din log-uri am vazut ca X-ul
porneste dar pe ecran imi apare un "OUT OF RANGE"..si singura scapare este
un reboot. am incercat diverse rezolutii si adancimi de culoare - the
same. pe un rh6.2 (xfree86 3.6?) mergea fara probleme.
so..ce as putea sa fac ?
==========
(II) APM: driver for the Alliance chipsets: AP6422, AT24, AT3D
(II) Primary Device is: PCI 00:10:0
(--) Assigning device section with no busID to primary device
(--) Chipset AT3D found
[....................................................]
(--) APM(0): VideoRAM: 4096 kByte
(II) APM(0): I2C bus "Alliance bus" initialized.
(II) APM(0): I2C device "Alliance bus:ddc2" registered.
(II) APM(0): I2C device "Alliance bus:ddc2" removed.
(--) APM(0): No DDC signal
(==) APM(0): Using gamma correction (1.0, 1.0, 1.0)
(==) APM(0): Min pixel clock set to 23 MHz
(==) APM(0): Max pixel clock is 144 MHz
(II) APM(0): My Monitor: Using hsync range of 31.50-48.50 kHz
(II) APM(0): My Monitor: Using vrefresh range of 50.00-70.00 Hz
(II) APM(0): Clock range: 23.12 to 144.00 MHz
(II) APM(0): Not using default mode "640x350" (vrefresh out of range)
(II) APM(0): Not using default mode "640x400" (vrefresh out of range)
(II) APM(0): Not using default mode "720x400" (vrefresh out of range)
(II) APM(0): Not using default mode "640x480" (vrefresh out of range)
(II) APM(0): Not using default mode "640x480" (vrefresh out of range)
(II) APM(0): Not using default mode "640x480" (vrefresh out of range)
(II) APM(0): Not using default mode "800x600" (vrefresh out of range)
(II) APM(0): Not using default mode "800x600" (vrefresh out of range)
(II) APM(0): Not using default mode "800x600" (hsync out of range)
(II) APM(0): Not using default mode "1024x768" (bad mode
clock/interlace/doublescan)
(II) APM(0): Not using default mode "1024x768" (hsync out of range)
(II) APM(0): Not using default mode "1024x768" (hsync out of range)
(II) APM(0): Not using default mode "1024x768" (hsync out of range)
(II) APM(0): Not using default mode "1152x864" (hsync out of range)
(II) APM(0): Not using default mode "1280x960" (hsync out of range)
(II) APM(0): Not using default mode "1280x960" (bad mode
clock/interlace/doublescan)
(II) APM(0): Not using default mode "1280x1024" (hsync out of range)
(II) APM(0): Not using default mode "1280x1024" (hsync out of range)
(II) APM(0): Not using default mode "1280x1024" (bad mode
clock/interlace/doublescan)
(II) APM(0): Not using default mode "1600x1200" (bad mode
clock/interlace/doublescan)
(II) APM(0): Not using default mode "1600x1200" (bad mode
clock/interlace/doublescan)
(II) APM(0): Not using default mode "1600x1200" (bad mode
clock/interlace/doublescan)
(II) APM(0): Not using default mode "1600x1200" (bad mode
clock/interlace/doublescan)
(II) APM(0): Not using default mode "1600x1200" (bad mode
clock/interlace/doublescan)
(II) APM(0): Not using default mode "1792x1344" (insufficient memory for
mode)
(II) APM(0): Not using default mode "1792x1344" (insufficient memory for
mode)
(II) APM(0): Not using default mode "1856x1392" (insufficient memory for
mode)
(II) APM(0): Not using default mode "1856x1392" (insufficient memory for
mode)
(II) APM(0): Not using default mode "1920x1440" (insufficient memory for
mode)
(II) APM(0): Not using default mode "1920x1440" (insufficient memory for
mode)
(II) APM(0): Not using default mode "1400x1050" (hsync out of range)
(II) APM(0): Not using default mode "1400x1050" (bad mode
clock/interlace/doublescan)
(--) APM(0): Virtual size is 800x600 (pitch 800)
(**) APM(0): Default mode "800x600": 40.0 MHz, 37.9 kHz, 60.3 Hz
(II) APM(0): Modeline "800x600" 40.00 800 840 968 1056 600 601 605 628
+hsync +vsync
===============
---
Pentru dezabonare, trimiteti mail la
[EMAIL PROTECTED] cu subiectul 'unsubscribe rlug'.
REGULI, arhive si alte informatii: http://www.lug.ro/mlist/
