Didier
It is HP note book and i can only use command line.
I have noticed one thing and want to share with you.
I am generating loss at the compressor end by Netem queue and capture packets
on ethernet interface at de-compressor end.
First,IR header which are generated by compressor after decompression failure.
In that case sometime i cannot see any request recovery message from
de-compressor but i have log messages " Unable to decompressor" at decompressor
node.
"Unable to decompressor" message is generated by decompressor when it send
error recovery message to compressor for IR header.
Secondly, decompressor failure is normally observed for a packet loss of more
than 30 sec instead of lower or higher traffic rate.
Please comment.
Regards
Faraz
________________________________
From: Didier Barvaux <[email protected]>
To: [email protected]
Sent: Thursday, April 4, 2013 7:48 PM
Subject: Re: [Rohc] ROHC robustness (Was: Re: Fw: Linux kernel support)
Faraz,
Thank you for the answers. My answers below.
> > Please send me the output of the following commands (run as root) to
> > find out from where the 2nd package comes:
> > # dpkg −−info rohc-lib
> No such directory
>
> > # dpkg −−info rohc
> > No such directory
Sorry, wrong command. Please try:
# dpkg-deb --info rohc-lib
# dpkg-deb --info rohc
> # cat /usr/share/doc/rohc/copyright
> No Output
>
> # cat /usr/share/doc/rohc-lib/copyright
> It's original content from the GIT repository
> <http://vyatt.com/git/vyatta-wirelessmodem>
>
> Upstream Author:
>
> <[email protected]>
> [...]
OK. No real information there. It seems to be the default template from
Vyatta.
> # file /opt/vyatta/sbin/rohc
> /opt/vyatta/sbin/rohc: ELF 32-bit LSB executable, Intel 80386,
> version 1 (SYSV), dynamically linked (uses shared libs), for
> GNU/Linux 2.6.18, stripped
>
> # ldd /opt/vyatta/sbin/rohc
> linux-gate.so.1 => (0xb7713000)
> libpthread.so.0 => /lib/libpthread.so.0 (0xb76f3000)
> libpcap.so.0.8 => /usr/lib/libpcap.so.0.8 (0xb76c0000)
> librohc_common.so.0 => /usr/lib/librohc_common.so.0 (0xb76b7000)
> librohc_comp.so.0 => /usr/lib/librohc_comp.so.0 (0xb769d000)
> librohc_decomp.so.0 => /usr/lib/librohc_decomp.so.0 (0xb7682000)
> libm.so.6 => /lib/libm.so.6 (0xb765c000)
> libc.so.6 => /lib/libc.so.6 (0xb7517000)
> /lib/ld-linux.so.2 (0xb7714000)
OK. So the "rohc" executable uses the ROHC library.
> #
> modinfo /lib/modules/3.0.32-1-586-vyatta/kernel/net/sched/sch_rohc.ko
> filename:
> /lib/modules/3.0.32-1-586-vyatta/kernel/net/sched/sch_rohc.ko
> depends: sched_rohc
> vermagic: 3.0.32-1-586-vyatta SMP mod_unload modversions 586
>
> #
> modinfo /lib/modules/3.0.32-1-586-vyatta/kernel/net/sched/sched_rohc.ko
> filename:
> /lib/modules/3.0.32-1-586-vyatta/kernel/net/sched/sched_rohc.ko
> license: GPL depends: vermagic: 3.0.32-1-586-vyatta SMP
> mod_unload modversions 586
OK. No additional information there.
> > Did you install the vyatta software yourself or was it pre-installed
> > on the hardware?
>
> I have not installed. It was pre-installed.
OK. What hardware is it? What company is the provider?
Regards,
Didier
_______________________________________________
Mailing list: https://launchpad.net/~rohc
Post to : [email protected]
Unsubscribe : https://launchpad.net/~rohc
More help : https://help.launchpad.net/ListHelp
_______________________________________________
Mailing list: https://launchpad.net/~rohc
Post to : [email protected]
Unsubscribe : https://launchpad.net/~rohc
More help : https://help.launchpad.net/ListHelp
