<snip of yesterday>
Two things so far today:
(a) I've also set up RPCemu on a MacBook (2015) and it works at the earth
shattering rate of a stated approx 55 mips.
(b) Started to try to get networking going on the Mac and got stuck.
I suspect part of the reason is that 'RPCEmu Networking Guide' is specified for
stable releases where the run command is indeed ./rpcemu
>From the page 'Linux Binary Configuration' I chose the 'sudo method' and did
>this in Terminal:
------- Start of attempt to do 'sudo ./rpcemu' ---------
tim@tim-VirtualBox:~/rpcemu/rpcemu-0.8.102$ ls
cmos.ram hd4.hdf poduleroms riscos-progs rpc.cfg rpclog.txt
COPYING hostfs readme.txt roms rpcemu-recompiler src
tim@tim-VirtualBox:~/rpcemu/rpcemu-0.8.102$ sudo ./rpcemu-recompiler
QStandardPaths: XDG_RUNTIME_DIR not set, defaulting to '/tmp/runtime-root'
------- End of attempt to do 'sudo ./rpcemu' ---------
The result of the above was that a second iteration of RPCemu started up OK.
I then edited rpc.cfg. This may have been a mistake and should have belonged
only to the 'chown method'.
Back to the RPCEmu Networking Guide and a check on the running network
interfaces:
-------- Start of 'if config' --------
tim@tim-VirtualBox:~/rpcemu/rpcemu-0.8.102$ ifconfig -a
enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.1.31 netmask 255.255.255.0 broadcast 192.168.1.255
inet6 fe80::ac39:5e9c:a15:5257 prefixlen 64 scopeid 0x20<link>
ether 08:00:27:2e:33:3f txqueuelen 1000 (Ethernet)
RX packets 266731 bytes 155038039 (155.0 MB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 89971 bytes 13023739 (13.0 MB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 2513 bytes 196530 (196.5 KB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 2513 bytes 196530 (196.5 KB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
-------- End of 'if config' -------
The first of the two interfaces was (probably) the one running on Ubuntu to
talk to VirtualBox.
I then tried to issue the commands on the Ubuntu interface:
-------- Start of interface commands --------
tim@tim-VirtualBox:~/rpcemu/rpcemu-0.8.102$ iptables -I FORWARD -m state
--state ESTABLISHED,RELATED -j ACCEPT
conntrack: Could not determine whether revision 3 is supported, assuming it is.
conntrack: Could not determine whether revision 3 is supported, assuming it is.
conntrack: Could not determine whether revision 3 is supported, assuming it is.
iptables v1.6.1: can't initialize iptables table `filter': Permission denied
(you must be root)
Perhaps iptables or your kernel needs to be upgraded.
tim@tim-VirtualBox:~/rpcemu/rpcemu-0.8.102$
-------- End of attempt at interface commands --------
You will note the error message that 'you must be root', so I definitely gave
up as I knew this had to be duff.
What should I have done?
--
Tim Powys-Lybbe
[email protected]
for a miscellany of bygones: http://powys.org/
_______________________________________________
Rpcemu mailing list
[email protected]
http://www.riscos.info/cgi-bin/mailman/listinfo/rpcemu
