My guess is (based on the fact that you do have communication between the SA system and the SMPP system, and the error message) is that the recipients adddress is a problem. I would suggest to verify this with your SMPP provider.
Dirk Bulinckx. -----Original Message----- From: Servers Alive Discussion List [mailto:[EMAIL PROTECTED] On Behalf Of Petr Bohac Sent: Saturday, May 12, 2007 9:26 AM To: Servers Alive Discussion List Subject: RE: [SA-list] SMPP doesn't work after upgrade to 6.x version I did some capture using MS Netmon 3.0 and seems the two systems are communicating each other but I'm not familiar with Netmon and there's too much garbage, at least for me ;) -----Original Message----- From: Servers Alive Discussion List [mailto:[EMAIL PROTECTED] On Behalf Of Petr Bohac Sent: Saturday, May 12, 2007 10:41 AM To: Servers Alive Discussion List Subject: RE: [SA-list] SMPP doesn't work after upgrade to 6.x version Actually don't have any but I can have a look on it ... Just curious because the older version worked fine ... -----Original Message----- From: Servers Alive Discussion List [mailto:[EMAIL PROTECTED] On Behalf Of Dirk Bulinckx Sent: Saturday, May 12, 2007 10:31 AM To: Servers Alive Discussion List Subject: RE: [SA-list] SMPP doesn't work after upgrade to 6.x version If you have a sniffer (netmon-sniffer-ethereal-...), can you then see the traffic is going to the smpp gateway? Dirk Bulinckx. -----Original Message----- From: Servers Alive Discussion List [mailto:[EMAIL PROTECTED] On Behalf Of Petr Bohac Sent: Saturday, May 12, 2007 8:16 AM To: Servers Alive Discussion List Subject: [SA-list] SMPP doesn't work after upgrade to 6.x version Hi Dirk, I've just upgraded our box from SA 5.1.1963 to the official 6 (2103) version (tried the latest beta too) and the SMPP alerts stopped working. The setup is the same, there's no change whatsoever. I've consulted the problem with our PBX admin and everything is fine. So after enabling maximum logging I've got this err: ERR SMPP send message: SMPP protocol error (invalid desination address).( 360) The destination address, assume it's PBX IP address, is 100% valid. Could you please look at it as it is a major problem for us and I have to keep running the old SA. Thank you Petr This e-mail including any attachment is intended only for the recipient(s) named. It may contain confidential information and should not be read, copied or otherwise used by any other person. If you are not a named recipient, please contact the sender and delete the e-mail from your system. The sender does not accept any liability for errors or omissions in the content of this message or for viruses, or any damage due to the e-mail. The recipient is advised to have appropriate virus check software. To unsubscribe send a message with UNSUBSCRIBE as subject to [email protected] If you use auto-responders (like out-of-the-office messages), then make sure that they are not send to the list nor to the individual members of the list that send a message. Doing this will get you removed from the list. To unsubscribe send a message with UNSUBSCRIBE as subject to [email protected] If you use auto-responders (like out-of-the-office messages), then make sure that they are not send to the list nor to the individual members of the list that send a message. Doing this will get you removed from the list. This e-mail including any attachment is intended only for the recipient(s) named. It may contain confidential information and should not be read, copied or otherwise used by any other person. If you are not a named recipient, please contact the sender and delete the e-mail from your system. The sender does not accept any liability for errors or omissions in the content of this message or for viruses, or any damage due to the e-mail. The recipient is advised to have appropriate virus check software. To unsubscribe send a message with UNSUBSCRIBE as subject to [email protected] If you use auto-responders (like out-of-the-office messages), then make sure that they are not send to the list nor to the individual members of the list that send a message. Doing this will get you removed from the list. This e-mail including any attachment is intended only for the recipient(s) named. It may contain confidential information and should not be read, copied or otherwise used by any other person. If you are not a named recipient, please contact the sender and delete the e-mail from your system. The sender does not accept any liability for errors or omissions in the content of this message or for viruses, or any damage due to the e-mail. The recipient is advised to have appropriate virus check software. To unsubscribe send a message with UNSUBSCRIBE as subject to [email protected] If you use auto-responders (like out-of-the-office messages), then make sure that they are not send to the list nor to the individual members of the list that send a message. Doing this will get you removed from the list. To unsubscribe send a message with UNSUBSCRIBE as subject to [email protected] If you use auto-responders (like out-of-the-office messages), then make sure that they are not send to the list nor to the individual members of the list that send a message. Doing this will get you removed from the list.
