/etc/network/interfaces accept bond0 and runs fine, I change : interfaces = bond0, lo bind interfaces only = Yes in smb.conf
I can ping from anywhere, but Samba can not autenticate any Windows. Then I change again and back in /etc/network/interfaces to eth0. And include in smb.conf : interfaces = bond0, ****eth0****, lo bind interfaces only = Yes And now everything is OK, both WinXP e Win9x can logon into domain. But 'eth0' still disable, see : bond0 Link encap:Ethernet HWaddr 00:0c:76:97:04:f3 inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::20c:76ff:fe97:4f3/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:290850 errors:0 dropped:0 overruns:0 frame:0 TX packets:285844 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:75906076 (72.3 MB) TX bytes:219213427 (209.0 MB) eth0 Link encap:Ethernet HWaddr 00:0c:76:97:04:f3 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:96067 errors:0 dropped:0 overruns:0 frame:0 TX packets:142953 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:28372347 (27.0 MB) TX bytes:109526393 (104.4 MB) Interrupt:18 Base address:0x2000 eth1 Link encap:Ethernet HWaddr 00:0c:76:97:04:f3 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:194783 errors:0 dropped:0 overruns:0 frame:0 TX packets:142891 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:47533729 (45.3 MB) TX bytes:109687034 (104.6 MB) Interrupt:19 Base address:0x9000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1324 errors:0 dropped:0 overruns:0 frame:0 TX packets:1324 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:106749 (104.2 KB) TX bytes:106749 (104.2 KB) I dont know Why change directly /etc/network/interfaces does not permit Win machines autenticate on Samba, but : # ifconfig bond0 192.168.1.2 netmask 255.255.255.0 # ifenslave -v bond0 eth0 eth1 # route add default gw 192.168.1.254 in terminal and changes in smb.conf, resolve my problem. Thanks a lot. 2008/9/20 Chris Smith <[EMAIL PROTECTED]>: > On Saturday 20 September 2008 11:35:42 am hamacker wrote: >> # ifconfig eth0 >> eth0 Link encap:Ethernet HWaddr 00:0c:76:97:04:f3 >> inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 > > eth0 should not have an address - it should belong only to bond0. > eth0 and eth1 are both slaves to the master bond0. > >> # The primary network interface >> auto eth0 >> iface eth0 inet static > > Should probably more like: > iface bond0 inet static > >> my smb.conf : >> [global] >> unix charset = UTF8 >> workgroup = VIDY2005 >> server string = %h server (Samba %v) >> interfaces = eth0, eth1 > > Should be: > interfaces = bond0, lo > bind interfaces only = Yes > -- To unsubscribe from this list go to the following URL and read the instructions: https://lists.samba.org/mailman/listinfo/samba