Hello Rolf,
with both (LAN/USB) connections, i get no such messages "{pixma]" in the
"Buttons:" section. I've tried different buttons (PDF, JPEG...BLACK,
COLOR).
Attached output and error output after pressing "COLOR SCAN" Button.
regards Matthias
Am Sonntag, den 03.02.2013, 20:49 +0100 schrieb Rolf Bensch:
> Hi Matthias,
>
> Please (1) activate debug messages with 'export SANE_DEBUG_PIXMA=11',
> (2) push one of your scanners's buttons and
> (3) read the button status with 'scanimage -A'.
>
> You should receive something similar like this:
>
> ...
> Buttons:
> --button-update
> Update button state
> [pixma] INTR T=1.580 len=32
> [pixma] 00000000:00 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> [pixma] 00000010:00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> [pixma]
> --button-1 <int> [1] [read-only]
> Button 1
> --button-2 <int> [0] [read-only]
> Button 2
> --original <int> [0] [read-only]
> Type of original to scan
> --target <int> [1] [read-only]
> Target operation type
> ...
>
> If you get lines with [pixma], please repeat this test ((2) & (3)) with
> all buttons and provide the output from all buttons. Please write the
> name of the button to the corresponding debug output.
>
> If you don't get lines with [pixma], Sane doesn't receive the USB
> interrupt from your scanner and I need to prepare a patch.
>
> Cheers,
> Rolf
>
>
>
>
> Am 03.02.2013 13:09, schrieb Matthias Thon:
> > Hello Rolf,
> >
> > ihave checked your informations. The MG6250 doesn't have a target
> > option. Only the two buttons.I have tryed many cases on the MG but the
> > value of the buttons stay's at value "0". Normaly i have conncted the
> > printer over wlan or ethernet. If i try to push "scan" and then "color"
> > i get an error on the printer, because he doesn't recocnice the scanning
> > PC. He shows me only "local USB".
> >
> > I have connected the printer with a USB_cable. Then i can push the
> > "color" or "grey" button and the printe waits for the scanning process.
> > But scanimage -A shows no changes. The only change is in the resolution
> > option. This option adds 4800 dpi.
> >
> > scanimage --button-controlled doesn't start the scan after pressing
> > "color" or "grey" button.
> >
> > Scanning from outside (xsane) works well.
> >
> > regards Matthias
> >
> > Am Samstag, den 02.02.2013, 18:09 +0100 schrieb Rolf Bensch:
> >> Hi Matthias,
> >>
> >> To discover the communication between Sane and scanbd try 'scanimage
> >> -A'. Press a button and start 'scanimage -A' again. Repeat this until
> >> you'll have the codes for all buttons.
> >>
> >> For my CS9000F I get data for --button-1, --button-2 *and* --target.
> >>
> >> Please have a look to my posting here:
> >> http://lists.alioth.debian.org/pipermail/sane-devel/2013-January/030828.html.
> >>
> >> If you don't get any codes for your buttons please contact me again.
> >> Then we have to patch the backend for your scanner.
> >>
> >> Cheers,
> >> Rolf
> >>
> >>
> >>
> >> Am 01.02.2013 16:59, schrieb Matthias Thon:
> >>> Hello,
> >>> i've tried to use scanbd with my MG6200 Series device. He finds
> >>> "button-1" and "button-2" option. But the value is still "0".
> >>>
> >>> I have try "Scan" -> "Black&White" or "Scan" -> "Color".
> >>>
> >>> Is there a way to see more detailed the communication between scanbd and
> >>> the device? (more then with debug level 7)
> >>>
> >>> regards
> >>>
> >>>
> >>>
> >
> >
> >
-------------- next part --------------
All options specific to device `pixma:04A91755_14B4F6':
Scan mode:
--resolution auto||75|150|300|600|1200|2400|4800dpi [75]
Sets the resolution of the scanned image.
--mode auto|Color|Gray|Lineart [Color]
Selects the scan mode (e.g., lineart, monochrome, or color).
--source Flatbed [Flatbed]
Selects the scan source (such as a document-feeder). Set source before
mode and resolution. Resets mode and resolution to auto values.
--button-controlled[=(yes|no)] [no]
When enabled, scan process will not start immediately. To proceed,
press "SCAN" button (for MP150) or "COLOR" button (for other models).
To cancel, press "GRAY" button.
Gamma:
--custom-gamma[=(auto|yes|no)] [yes]
Determines whether a builtin or a custom gamma-table should be used.
--gamma-table auto|0..255,...
Gamma-correction table. In color mode this option equally affects the
red, green, and blue channels simultaneously (i.e., it is an intensity
gamma table).
--gamma auto|0.299988..5 [2.2]
Changes intensity of midtones
Geometry:
-l auto|0..216.069mm [0]
Top-left x position of scan area.
-t auto|0..297.011mm [0]
Top-left y position of scan area.
-x auto|0..216.069mm [216.069]
Width of scan-area.
-y auto|0..297.011mm [297.011]
Height of scan-area.
Buttons:
--button-update
Update button state
--button-1 <int> [0]
Button 1
--button-2 <int> [0]
Button 2
Extras:
--threshold auto|0..100% (in steps of 1) [inactive]
Select minimum-brightness to get a white point
--threshold-curve auto|0..127 (in steps of 1) [inactive]
Dynamic threshold curve, from light to dark, normally 50-65
-------------- next part --------------
[sanei_debug] Setting debug level of pixma to 11.
[pixma] pixma is compiled with pthread support.
[pixma] pixma version 0.17.0
[pixma] pixma_collect_devices() found Canon PIXMA MG6200 at libusb:002:010
[pixma] sanei_bjnp_find_devices:
[pixma] Added all configured scanners, now do auto detection...
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is not a valid IPv4 interface, skipping...
[pixma] wlan0 is not a valid IPv4 interface, skipping...
[pixma] vboxnet0 is not a valid IPv4 interface, skipping...
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is IPv4 capable, sending broadcast..
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is not a valid IPv4 interface, skipping...
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is not a valid IPv4 interface, skipping...
[pixma] wlan0 is not a valid IPv4 interface, skipping...
[pixma] vboxnet0 is not a valid IPv4 interface, skipping...
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is IPv4 capable, sending broadcast..
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is not a valid IPv4 interface, skipping...
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is not a valid IPv4 interface, skipping...
[pixma] wlan0 is not a valid IPv4 interface, skipping...
[pixma] vboxnet0 is not a valid IPv4 interface, skipping...
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is IPv4 capable, sending broadcast..
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is not a valid IPv4 interface, skipping...
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is not a valid IPv4 interface, skipping...
[pixma] wlan0 is not a valid IPv4 interface, skipping...
[pixma] vboxnet0 is not a valid IPv4 interface, skipping...
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is IPv4 capable, sending broadcast..
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is not a valid IPv4 interface, skipping...
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is not a valid IPv4 interface, skipping...
[pixma] wlan0 is not a valid IPv4 interface, skipping...
[pixma] vboxnet0 is not a valid IPv4 interface, skipping...
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is IPv4 capable, sending broadcast..
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is not a valid IPv4 interface, skipping...
[pixma] scanner discovery finished...
[pixma] pixma_find_scanners() found 1 devices
[pixma] pixma_collect_devices() found Canon PIXMA MG6200 at libusb:002:010
[pixma] sanei_bjnp_find_devices:
[pixma] Added all configured scanners, now do auto detection...
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is not a valid IPv4 interface, skipping...
[pixma] wlan0 is not a valid IPv4 interface, skipping...
[pixma] vboxnet0 is not a valid IPv4 interface, skipping...
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is IPv4 capable, sending broadcast..
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is not a valid IPv4 interface, skipping...
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is not a valid IPv4 interface, skipping...
[pixma] wlan0 is not a valid IPv4 interface, skipping...
[pixma] vboxnet0 is not a valid IPv4 interface, skipping...
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is IPv4 capable, sending broadcast..
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is not a valid IPv4 interface, skipping...
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is not a valid IPv4 interface, skipping...
[pixma] wlan0 is not a valid IPv4 interface, skipping...
[pixma] vboxnet0 is not a valid IPv4 interface, skipping...
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is IPv4 capable, sending broadcast..
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is not a valid IPv4 interface, skipping...
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is not a valid IPv4 interface, skipping...
[pixma] wlan0 is not a valid IPv4 interface, skipping...
[pixma] vboxnet0 is not a valid IPv4 interface, skipping...
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is IPv4 capable, sending broadcast..
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is not a valid IPv4 interface, skipping...
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is not a valid IPv4 interface, skipping...
[pixma] wlan0 is not a valid IPv4 interface, skipping...
[pixma] vboxnet0 is not a valid IPv4 interface, skipping...
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is IPv4 capable, sending broadcast..
[pixma] lo is not a valid IPv4 interface, skipping...
[pixma] eth0 is not a valid IPv4 interface, skipping...
[pixma] scanner discovery finished...
[pixma] pixma_open(): Canon PIXMA MG6200
[pixma] pixma_close(): Canon PIXMA MG6200
