RE: [Asterisk-Users] How to setup two Asterisk boxes - keeping theregistration
You'll need to create a trunk between the two systems Then configure your out bound routing to use that trunk Eg if you use 1 as the prefix for the trunk BOX A Ext200 will call box B EXT201 by dialing 1201 -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Ronald Wiplinger Sent: Sunday, 19 June 2005 12:46 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: [Asterisk-Users] How to setup two Asterisk boxes - keeping theregistration I have now two asterisk boxes running, one on the IP *18 and one on IP *20 Both are working, use the same dialplan and realtime. I did not find out how to set it up that if a phone is registered in *18 can reach a phone registered in *20. For the wake up call I also see some troubles, since both machines point to the same NFS space. It could be that both machines start the wakeup call. Has anybody solved that? bye Ronald ___ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users This email and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed. If you have received this email in error please notify the originator of the message. This footer also confirms that this email message has been scanned for the presence of computer viruses. Any views expressed in this message are those of the individual sender, except where the sender specifies and with authority, states them to be the views of LMC. ___ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
[Asterisk-Users] Hangup Issues on TDM40B FXO Australia
Afternoon all, After doing some test on my asterisk box I can successfully receive calls to my Asterisk PBX to a SIP phone from The Telstra PSTN network Dial out from a sip phone is also not an issue, all calls connect and terminate normally. If I call the Asterisk PBX say from PSTN in Zap1-1 and out through ZAP2-2 back to the PSTN (after entering the correct pin off course) the card does not appear to detect the hang-up, I then have to issues a soft hang-up to close the call, I presume this indicates the card is configured to receive the correct hangup signal I have tried enabling callprogress, busydetect and a few settings on the busycount but to no success I've also tried LS and KS signalling Does anyone else have any suggestions to get this to work with Australia's Telstra? Regards Haydn This email and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed. If you have received this email in error please notify the originator of the message. This footer also confirms that this email message has been scanned for the presence of computer viruses. Any views expressed in this message are those of the individual sender, except where the sender specifies and with authority, states them to be the views of LMC. ___ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
RE: [Asterisk-Users] Hangup Issues on TDM40B FXO Australia
Thanks for the response all I'm Currently running version 1.0.7 of asterisk, Key configuration lines as below, for those who have it working is there anything that stands out as incorrect? * Zaptel.conf fxsls=1-4 loadzone=au defaultzone=au *** Zapata.conf signalling=fxs_ls switchtype=national *** zapata-channels.conf signalling=fxs_ls *** zapata_additional.conf ;;[EXT] signalling=fxo_ls echotraining=400 echocancelwhenbridge=no echocancel=yes context=from-internal callprogress=yes busydetect=yes busycount=3 channel=1 *** -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Terry H. Gilsenan Sent: Monday, 23 May 2005 1:35 PM To: 'Asterisk Users Mailing List - Non-Commercial Discussion' Subject: RE: [Asterisk-Users] Hangup Issues on TDM40B FXO Australia Hi, I have 2 Asterisk servers in .pg and 2 in .au In .pg I have had to configure them as if they were in .au and use LS signaling. I am using the latest Asterisk @ Home (1.0) and it is working well with 1 TDM400P for interfacing with the PSTN lines. Previously I had exactly the problem you have described using Asterisk @ Home (0.7). I also had a memory leak problem in that all the memory 512Mb would be gradually used up and after about 3 days the audio would begin to suffer. The upgrade was a full reinstall and rebuild from documentation and once completed, the problems have not reappeared. These server are also NTP servers and DHCP servers Regards, T -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of [EMAIL PROTECTED] Sent: Monday, 23 May 2005 12:49 PM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] Hangup Issues on TDM40B FXO Australia Afternoon all, After doing some test on my asterisk box I can successfully receive calls to my Asterisk PBX to a SIP phone from The Telstra PSTN network Dial out from a sip phone is also not an issue, all calls connect and terminate normally. If I call the Asterisk PBX say from PSTN in Zap1-1 and out through ZAP2-2 back to the PSTN (after entering the correct pin off course) the card does not appear to detect the hang-up, I then have to issues a soft hang-up to close the call, I presume this indicates the card is configured to receive the correct hangup signal I have tried enabling callprogress, busydetect and a few settings on the busycount but to no success I've also tried LS and KS signalling Does anyone else have any suggestions to get this to work with Australia's Telstra? Regards Haydn -- -- This email and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed. If you have received this email in error please notify the originator of the message. This footer also confirms that this email message has been scanned for the presence of computer viruses. Any views expressed in this message are those of the individual sender, except where the sender specifies and with authority, states them to be the views of LMC. -- -- ___ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users This email and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed. If you have received this email in error please notify the originator of the message. This footer also confirms that this email message has been scanned for the presence of computer viruses. Any views expressed in this message are those of the individual sender, except where the sender specifies and with authority, states them to be the views of LMC. ___ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit:
RE: [Asterisk-Users] Hangup Issues on TDM40B FXO Australia
Thanks Terry noticed [EMAIL PROTECTED] 0.7 will try version 1 -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Terry H. Gilsenan Sent: Monday, 23 May 2005 1:35 PM To: 'Asterisk Users Mailing List - Non-Commercial Discussion' Subject: RE: [Asterisk-Users] Hangup Issues on TDM40B FXO Australia Hi, I have 2 Asterisk servers in .pg and 2 in .au In .pg I have had to configure them as if they were in .au and use LS signaling. I am using the latest Asterisk @ Home (1.0) and it is working well with 1 TDM400P for interfacing with the PSTN lines. Previously I had exactly the problem you have described using Asterisk @ Home (0.7). I also had a memory leak problem in that all the memory 512Mb would be gradually used up and after about 3 days the audio would begin to suffer. The upgrade was a full reinstall and rebuild from documentation and once completed, the problems have not reappeared. These server are also NTP servers and DHCP servers Regards, T -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of [EMAIL PROTECTED] Sent: Monday, 23 May 2005 12:49 PM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] Hangup Issues on TDM40B FXO Australia Afternoon all, After doing some test on my asterisk box I can successfully receive calls to my Asterisk PBX to a SIP phone from The Telstra PSTN network Dial out from a sip phone is also not an issue, all calls connect and terminate normally. If I call the Asterisk PBX say from PSTN in Zap1-1 and out through ZAP2-2 back to the PSTN (after entering the correct pin off course) the card does not appear to detect the hang-up, I then have to issues a soft hang-up to close the call, I presume this indicates the card is configured to receive the correct hangup signal I have tried enabling callprogress, busydetect and a few settings on the busycount but to no success I've also tried LS and KS signalling Does anyone else have any suggestions to get this to work with Australia's Telstra? Regards Haydn -- -- This email and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed. If you have received this email in error please notify the originator of the message. This footer also confirms that this email message has been scanned for the presence of computer viruses. Any views expressed in this message are those of the individual sender, except where the sender specifies and with authority, states them to be the views of LMC. -- -- ___ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users ___ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users This email and any files transmitted with it are confidential and intended solely for the use of the individual or entity to whom they are addressed. If you have received this email in error please notify the originator of the message. This footer also confirms that this email message has been scanned for the presence of computer viruses. Any views expressed in this message are those of the individual sender, except where the sender specifies and with authority, states them to be the views of LMC. ___ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
