Low BRI througput [7:12078]
Dear Sir Cisco recommends for low throughput for the ISDN BRI to verify that fair queuing is not enabled can anyone tell me the relationship between fair queuing and BRI throughput ? Best Regards, Mohammed Saro Network Engineer GEGA NET Tel: +202-4149771 Ext:111 Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=12078&t=12078 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
ACESS-LIST [7:12085]
I have A problem when i enabled CEF on a 4500 router with ios 12.0(5) T i have a problem that when i apply a new access-list it does not make any matches unless i disable then reenable the ip cef on the router what is that ? Best Regards, Mohammed Saro Network Engineer GEGA NET Tel: +202-4149771 Ext:111 Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=12085&t=12085 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Mawhoob [7:12107]
i have a problem with one DSL customer with a speed of 128 kbps conected to my company through 2 exchanges via copper wires 0.4 mm thick the line is up and the protocols goes up and down i checked the H/W it is ok but the physical line has input errors and crc's whta is the solution Best Regards, Mohammed Saro Network Engineer GEGA NET Tel: +202-4149771 Ext:111 Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=12107&t=12107 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Low BRI througput [7:12078]
it is recommended in the BCRAN book But i didn't understande what u said what is the fragmentation delay ? Best Regards, Mohammed Saro Network Engineer GEGA NET Tel: +202-4149771 Ext:111 - Original Message - From: "Charlie Hartwell" To: Sent: Thursday, July 12, 2001 11:53 AM Subject: Re: Low BRI througput [7:12078] > It would be interesting to see the document that recommends that > action - after all, WFQ is designed to help with low bandwidth links > without the need for complicated config. > > It is more likely that it is recommended to turn off WFQ when using > ppp multilink across the ISDN connection. This is probably to avoid > any unnecessary fragment delay which could lead to malformed packets > and retransmissions. > > So in answer to your question, there is no real connection between > BRI performance and WFQ but cisco probably recommend disabling WFQ to > avoid other problems. > > Cheers > > Charlie > > --- Mohammed Saro wrote: > Dear Sir > > Cisco recommends for low throughput for the ISDN BRI to verify > > that fair > > queuing is not enabled can anyone tell me the relationship between > > fair > > queuing and BRI throughput ? > > > > Best Regards, > > Mohammed Saro > > Network Engineer > > GEGA NET > > Tel: +202-4149771 Ext:111 > [EMAIL PROTECTED] > > > > Do You Yahoo!? > Get your free @yahoo.co.uk address at http://mail.yahoo.co.uk > or your free @yahoo.ie address at http://mail.yahoo.ie Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=12105&t=12078 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
default route problem [7:14118]
i have a problem when i configured OSPF on my system and make redistribution for the static routes all routes are transmitted except the default route so when u write sh ip orute 0.0.0.0 any where else u find that Network not in the table how comes that all static routes are exchanged except the default route ? Best Regards, Mohammed Saro Network Engineer Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=14118&t=14118 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re:access list w/prime numbers [7:14117]
when the last octet is a prime number so it first bit will always be 1 so u can put access list like this access-list 101 deny 192.168.1.1 255.255.255.254 192.168.1.0 0.0.0.255 Best Regards, Mohammed Saro Network Engineer - Original Message - From: "Alejandro Pelaez" To: Sent: Monday, July 30, 2001 9:57 AM Subject: access list w/ prime numers [7:14117] > Hola All! > > I want to set up an access list that do the following: > deny all packets from subnet 192.168.1.0 with last octect a prime numer. > > Alejandro Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=14120&t=14117 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
unexpected traffic [7:14162]
i have a problem of unexpected traffic on one of router interfaces and when the problem happens i can not analyze this traffic when i use ip accounting output-packets i can not recognize how is this happens i found on the interface of the international bandwidth packets sourced with internal ips how is that i really would like help to analyze this traffic and to understand how how does ip accounting work Mohammed Saro Network Engineer Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=14162&t=14162 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
design issues [7:14454]
i have acase and i want some1 to help me to solve it a company has two sites they want to have dedicated line with 128 kbps on site 1 and to make an ISDN dial backup to the ISP then site 2 is connected to site 1 with dedicated line of 128kbps and they have ISDN line their but they face sometimes problems with their line in site 1 so they need in case of failure of the ddicated liune betwenn their site 1 and the ISP and the failure of site 1 ISDN backup to dial the ISP they want the ISDN line of site 2 to dial to the ISP and will be in this case the gateway of two sites the question now how can i trigger dial on ISDN line in site 2 in case of failure of dedicated then failure of ISDNline of site 1 with the caution that the bri interface always up up spoofing Mohammed Saro Network Engineer Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=14454&t=14454 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
how to analyze traffic [7:14458]
i have a problem of unexpected traffic on one of router interfaces and when the problem happens i can not analyze this traffic when i use ip accounting output-packets i can not recognize how is this happens i found on the interface of the international bandwidth packets sourced with internal ips how is that i really would like help to analyze this traffic and to understand how how does ip accounting work Mohammed Saro Network Engineer Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=14458&t=14458 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
urgent problem [7:14942]
24 608A5838 608A5910 1 6042F878 Router Init 608A5910112 608A58D0 608A59A8 1 6042F890 OSPF RBTree 608A59A8 24 608A5910 608A59E8 1 6042F878 Router Init 608A59E8112 608A59A8 608A5A80 1 6042F890 OSPF RBTree 608A5A80 24 608A59E8 608A5AC0 1 6042F878 Router Init 608A5AC0112 608A5A80 608A5B58 1 6042F890 OSPF RBTree Address Bytes Prev.Next Ref PrevF NextF Alloc PC What 608A5B58 24 608A5AC0 608A5B98 1 6042F878 Router Init 608A5B98112 608A5B58 608A5C30 1 6042F890 OSPF RBTree 608A5C30416 608A5B98 608A5DF8 1 602E4D38 Router Init 608A5DF8304 608A5C30 608A5F50 1 602E82FC Router Init 608A5F50 24 608A5DF8 608A5F90 1 601DD7EC Router Init 608A5F90 24 608A5F50 608A5FD0 1 601DD7EC Router Init 608A6040112 608A5FD0 608A60D8 1 602E98E4 Router Init 608A60D8 64 608A6040 608A6140 1 602E9908 Router Init 608A6140456 608A60D8 608A6330 1 602E2980 Router Init 608A6330112 608A6140 608A63C8 1 6042F890 OSPF RBTree 608A63C8 24 608A6330 608A6408 1 6042F878 Router Init 608A6408112 608A63C8 608A64A0 1 6042F890 OSPF RBTree 608A64A0 24 608A6408 608A64E0 1 6042F878 Router Init 608A64E0112 608A64A0 608A6578 1 6042F890 OSPF RBTree 608A6578 24 608A64E0 608A65B8 1 6042F878 Router Init 608A65B8112 608A6578 608A6650 1 6042F890 OSPF RBTree 608A6650 24 608A65B8 608A6690 1 6042F878 Router Init 608A6690112 608A6650 608A6728 1 6042F890 OSPF RBTree 608A6728 24 608A6690 608A6768 1 6042F878 Router Init 608A6768112 608A6728 608A6800 1 6042F890 OSPF RBTree 608A6800416 608A6768 608A69C8 1 602E4D38 Router Init 608A69C8304 608A6800 608A6B20 1 602E82FC Router Init 608A6B20 24 608A69C8 608A6B60 1 601DD7EC Router Init 60B5EFE8 60 60B5EF84 60B5F04C 1 6040AF18 SWIDB_SB: NETBI OS Info 60B5F04C 60 60B5EFE8 60B5F0B0 1 6040AF18 SWIDB_SB: NETBI OS Info 60B5F0B0 60 60B5F04C 60B5F114 1 6040AF18 SWIDB_SB: NETBI OS Info 60B5F114 60 60B5F0B0 60B5F178 1 6040AF18 SWIDB_SB: NETBI OS Info 60B5F178 60 60B5F114 60B5F1DC 1 6040AF18 SWIDB_SB: NETBI OS Info 60B60250 60 60B601B4 60B602B4 1 6040AF18 SWIDB_SB: NETBI OS Info 60B602B4 60 60B60250 60B60318 1 6040AF18 SWIDB_SB: NETBI OS Info 60B60318 60 60B602B4 60B6037C 1 6040AF18 SWIDB_SB: NETBI OS Info 60B6037C 60 60B60318 60B603E0 1 6040AF18 SWIDB_SB: NETBI OS Info 60B603E0 60 60B6037C 60B60444 1 6040AF18 SWIDB_SB: NETBI OS Info 60B60444 60 60B603E0 60B604A8 1 6040AF18 SWIDB_SB: NETBI OS Info 60B604A8 60 60B60444 60B6050C 1 6040AF18 SWIDB_SB: NETBI OS Info 60B6050C 60 60B604A8 60B60570 1 6040AF18 SWIDB_SB: NETBI OS Info 60B60570 60 60B6050C 60B605D4 1 6040AF18 SWIDB_SB: NETBI OS Info 60B605D4 60 60B60570 60B60638 1 6040AF18 SWIDB_SB: NETBI OS Info 60B60638 60 60B605D4 60B6069C 1 6040AF18 SWIDB_SB: NETBI OS Info 60B6069C 60 60B60638 60B60700 1 6040AF18 SWIDB_SB: NETBI OS Info 60B60700 60 60B6069C 60B60764 1 6040AF18 SWIDB_SB: NETBI OS Info 60B60764 60 60B60700 60B607C8 1 6040AF18 SWIDB_SB: NETBI OS Info 60B607C8 60 60B60764 60B6082C 1 6040AF18 SWIDB_SB: NETBI OS Info 60B6082C 60 60B607C8 60B60890 1 6040AF18 SWIDB_SB: NETBI OS Info -- 14224 I/O memory Address Bytes Prev.Next Ref PrevF NextF Alloc PC What sh ip route summary total consumption of the routing table around 60 k Best Regards, Mohammed Saro Network Engineer Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=14942&t=14942 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: urgent problem [7:14942]
yeah but i want urgent solution i do not have enough fash or RAM to upgrade IOS and i'm suspecting a hardware failure so how can i know is it hardware failure or just software hangs Best Regards, Mohammed Saro Network Engineer - Original Message - From: "Michael R. Eckhoff" To: Sent: Sunday, August 05, 2001 2:39 PM Subject: Re: urgent problem [7:14942] > Yeah - I've had a similar problem with a 3640 running 11.x code. Up it > to 12.0.18 if you can and it should go away. Mine has been rock solid > ever since. > > Other things I noticed, besides the intermitant connectivity, would be > that the whole box would hang while you were on it for periods of time. > Then it come back like nothing ever happened. > > All related to memory allocation. > > Mike > > Mohammed Saro wrote: > > i have router 3640 with 12m processorr memory and 4M I/o memory running > ospf > > process suddenly i can not telnet soemtimes it works sometimes not and > when i > > log to console i find that there is a problem in its memory allocation here > > are some show comands it might help please advice as soon as possible i > want > > to know is it bug in IOS or memory leakage or harware failure > > > > %SYS-2-MALLOCFAIL:memory allocation of 128975 bytes failed from 0x601451F8, > > pool processor alignment 0 > > > > %Low-on-Memory > > > > > > > > R002#sh ver > > Cisco Internetwork Operating System Software > > IOS (tm) 3600 Software (C3640-I-M), Version 11.2(7a)P, SHARED PLATFORM, > > RELEASE > > SOFTWARE (fc1) > > Copyright (c) 1986-1997 by cisco Systems, Inc. > > Compiled Wed 02-Jul-97 07:24 by ccai > > Image text-base: 0x600088E0, data-base: 0x6044 > > > > ROM: System Bootstrap, Version 11.1(7)AX [kuong (7)AX], EARLY DEPLOYMENT > > RELEASE > > SOFTWARE (fc2) > > > > R002 uptime is 1 hour, 7 minutes > > System restarted by power-on > > System image file is "flash:c3640-i-mz.112-7a.P", booted via flash > > > > cisco 3640 (R4700) processor (revision 0x00) with 12288K/4096K bytes of > > memory. > > Processor board ID 05691894 > > R4700 processor, Implementation 33, Revision 1.0 > > Channelized E1, Version 1.0. > > Bridging software. > > X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. > > Primary Rate ISDN software, Version 1.0. > > 2 Ethernet/IEEE 802.3 interface(s) > > 8 Serial network interface(s) > > 16 Low-speed serial(sync/async) network interface(s) > > 1 Channelized E1/PRI port(s) > > DRAM configuration is 64 bits wide with parity disabled. > > 125K bytes of non-volatile configuration memory. > > 4096K bytes of processor board System flash (Read/Write) > > > > Configuration register is 0x2102 > > > > > > R002#sh processes memory > > Total: 5984448, Used: 5887396, Free: 97052 > > PID TTY Allocated FreedHoldingGetbufsRetbufs Process > >00 194856 12362121464 0 0 *Init* > >00288 300560288 0 0 *Sched* > >0062287161719112 14224 297060 0 *Dead* > >10256256 3772 0 0 Load Meter > >20 1216 80760 7804 0 0 OSPF Hello > >30 0 0 6772 0 0 Check > heaps > >40 73128 0 49660 25736 0 Pool > Manager > >50256256 6772 0 0 Timers > >60172 4068 6944 0 0 ARP Input > >70 92 0 6864 0 0 SERIAL > > A'dete > >80256256 6772 0 0 > > Environmental > > tatus checker > >90 0 0 6772 0 0 SYNCD2430 > > Hel > > r > > 100 26652 3632 24896 0 0 Framer > > backgr > > nd > > 110 43720724 498283114308780 0 IP Input > > 120 86680 78880 14572 0 0 CDP > Protocol > > 130 0 0 6772 0 0 Asy FS > > Helper > > 140 0 19428 6772 0 0 TCP Timer > > 150 358116 29920 15752 0 0 TCP > > Protocols > > 160232 0 7004 0 0 Probe > Input > > 170
Re: High CPU Utilization [7:15272]
u can use CEF and DCEF Best Regards, Mohammed Saro Network Engineer GEGA NET +202-4149771/2/3/4 ext.111 - Original Message - From: "Nabil Fares" To: Sent: Wednesday, August 08, 2001 4:54 PM Subject: High CPU Utilization [7:15272] > Greetings, > > Any tips on improving high cpu utilization on a Cisco 7500? > > 4 T1s > 1 HSSI > 1 TokenRing Port > 2 FastEthernet (Bundled, FEC) > > Its running around 54%, any segmentations would be great. > > Thanks, > > Nabil Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=15434&t=15272 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
MMP [7:28052]
I want to enable multichassis multilink ppp on three 5400 universal access servers accepting both analog and ISDN calls i use groups async interface as a profile for analog calls and configuring the d channel of PRI to b the profile for ISDN calls should i create virtual template and how can i make sure that MMP is running correctly Best Regards, Mohamed Saro Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=28052&t=28052 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Multichassis Multilink PPP [7:28571]
I want to enable multichassis multilink ppp on three 5400 universal access servers accepting both analog and ISDN calls i use groups async interface as a profile for analog calls and configuring the d channel of PRI to b the profile for ISDN calls should i create virtual template and how can i make sure that MMP is running correctly Best Regards, Mohamed Saro Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=28571&t=28571 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Multihoming load balancing BGP [7:30011]
Any ideas to load balance when multihoming ? Best Regards, Mohamed Saro Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=30011&t=30011 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
calling number [7:30521]
I want to configure to receive a number (calling number) on DID with R2 signaling how to do it ? Mohamed Saro Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=30521&t=30521 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
B number [7:31142]
how to configure to receive the B number or the called number on AS5400 Best Regards, Mohamed Saro Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=31142&t=31142 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
multiple radius server [7:31781]
I want to send accounting packets to multiple radius servers simultaneously when i add them in sequence it sends to them in a failover order Mohamed Saro Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=31781&t=31781 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
multiple RADIUS servers [7:31995]
how can i configure multiple silmultaneous RADIUS servers to receive accountign packets on cisco 5400 Mohamed Saro Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=31995&t=31995 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
cpu utilization with MRTG [7:32677]
Any ideas about object ID of CPU utilization on Cisco routers for monitoring with MRTG Mohamed Saro Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=32677&t=32677 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
new CIT [7:47777]
What about 640-606 any one knows what happens to the AppleTalk,tokenring, FDDI, and IPX questions? did they reduce them or what ? Best Regards, Mohamed Saro Network Division Manager T.E. DATA Tel: +20-10-1663531 Tel: +20- 2 -7494025 Ext:1102 Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=4&t=4 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
VPN dialer [7:18217]
I want a VPN dialer and a sample configuration to dial to an ISP then establish VPN between VPN client and the main branch with IOS IP IP PLUS 56 and router 1720 Mohammed Saro Network Engineer Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=18217&t=18217 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
VPN dialer [7:18309]
I want a VPN dialer and a sample configuration to dial to an ISP then establish VPN between VPN client and the main branch with IOS IP IP PLUS 56 and router 1720 Mohammed Saro Network Engineer Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=18309&t=18309 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
BRI D channel [7:20241]
the D channel is the channel that takes the ip address so how can i dial to two different locations with the same BRI interface and the other question about cisco BOD how can i use dialer load-threshold load without enabling MLPPP what will happen to ips is it will take two different ips ? Best Regards, Mohammed Saro Network Engineer Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=20241&t=20241 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
ADSL rates [7:20506]
How can i divide a given bandwidth between leased lines and ADSL subscribers any hints or guides for dividing bandwidth among them and about the sharing ratios Best Regards, Mohamed Saro Network Engineer Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=20506&t=20506 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
MTU effect [7:22023]
what is the effect of lowering MTU on the throughput and on packets Best Regards, Mohamed Saro Network Engineer Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=22023&t=22023 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
load sharing [7:24752]
We have two links to our provider and this provider makes load sharing per packet but sometimes one of two links is saturated and the other has free bandwidth can any one explain this weird behavior Best Regards, Mohamed Saro Senior Network Engineer GEGA NET Tel: +20 2 4149771/2/3/4 ext.:111 Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=24752&t=24752 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
load sharing
We have two links to our provider and this provider makes load sharing per packet but sometimes one of two links is saturated and the other has free bandwidth can any one explain this weird behavior Best Regards,Mohamed SaroSenior Network Engineer GEGA NETTel: +20 2 4149771/2/3/4ext.:111
load sharing
[ Part 1, Text/PLAIN (charset: Unknown "windows-1256") 12 lines. ] [ Unable to print this part. ] [ The following text is in the "windows-1256" character set. ] [ Your display is set for the "US-ASCII" character set. ] [ Some characters may be displayed incorrectly. ] We have two links to our provider and this provider makes load sharing per packet but sometimes one of two links is saturated and the other has free bandwidth can any one explain this weird behavior Best Regards, Mohamed Saro Senior Network Engineer GEGA NET Tel: +20 2 4149771/2/3/4 ext.:111
password managment [7:26203]
I want ideas about managing large network passwords consists of may 40 nodes or more Best Regards, Mohamed Saro Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=26203&t=26203 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
DB60 back to back [7:48755]
I need to know from where I can get cables DB60 back to back to connect two routers directly Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=48755&t=48755 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
7500 VIP prompt [7:49927]
Can anyone tell me how to log to the VIP prompt of the 75xx series Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=49927&t=49927 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Router Error [7:51347]
If you have a cco account you can try http://www.cisco.com/cgi-bin/Support/Errordecoder/error_decoder.pl?index=ios &query=+%25ALIGN-3-TRACE%3A+-Traceback%3D+601D044C+6033D758+602F3018+000 0&counter=0&paging=5&links=reference&sa=Submit 1. %LANCE-3-BADCABLE: Unit [dec], Transmits stalled. Check ethernet cable connection The Ethernet cable is not connected. Recommended Action: Check the Ethernet cable connection. Related documents: No specific documents apply to this error message. - Original Message - From: "Steiven Poh-(Jaring MailBox)" To: Sent: Wednesday, August 14, 2002 2:14 PM Subject: Router Error [7:51347] > Dear All, > > Could anyone advice below error msg, I have test the cable seem to be ok? > Thanks... > > 01:47:36: %LANCE-3-BADCABLE: Unit 0, Transmits stalled. Check ethernet cable > connection > > > Rgds, > Steiven Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=51351&t=51347 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RADB [7:51718]
what is RADB ? and what is the importance to send updates for the BGP policies after updating the RIR like RIPE NCC Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=51718&t=51718 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]