Re: Connecting WIC-1DSU? [7:61487]
You need to make a T1 cross-over cable. Pins 1,2 go to pins 4,5 and reverse. check the archives on groupstudy as this has been talked about indepth before. thanks, -Brad Ellis CCIE#5796 (R&S / Security) Network Learning Inc [EMAIL PROTECTED] www.ccbootcamp.com (cisco training) ""Mike Mihalas"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > Is it possible to connect a WIC-1DSU-T1 to another WIC-1DSU-T1 to simulate a > circuit? I have two 2600's that I would like to connect to do some testing > with. If it is possible, do I need a special cable? > > Thanks in advance, > > Mike Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=61497&t=61487 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Connecting WIC-1DSU? [7:61487]
I think the correct cabling is DESCRIPTION PIN # COLOR Receive from Network (ring) 1 Blue/White Receive from Network (tip) 2 White/Blue Transmit from Network (ring)4 Orange/White Transmit from Network (tip) 5 White/Orange so in this case should be 1-4 and 2-5. For additional information please take a look on: http://www.juniper.net/techpubs/qrc/pics-qrc.pdf Regards Stefan Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=61571&t=61487 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Connecting WIC-1DSU? [7:61487]
Daniel Cotts wrote: > > You are correct. the 568A or B spec shows that pin 1 is tip and > 2 is ring. > Pin 4 is ring and pin 5 is tip for pair one. So for a tip to > tip and ring to > ring crossover then 2 to 4 and 1 to 5 is correct. Our copy of the 568 series TIA/EIA specs are out on a construction site at the moment. I'll be over there tomorrow so I'll take a look. You are exactly correct that the 568 series calls pin 1 a Tip, pin 2 a Ring, pin 5 a Tip, and pin 4 a Ring. So a 568 rollover is as you said. I don't know if the 568 series was ever intended to cover T1 though (it's common practice to use 568 patch cords for T1s these days, I'm just not clear that the spec was intended to encompass T1 stuff). I looked at ISOCs RJ-48C and RJ-48X, which apparently calls pin 1 a Ring, pin 2 a Tip, pin 4 a Ring, and pin 5 a Tip. The RJ spec is just a connector spec as far as I know. However, it was a connector spec geared specifically towards 1.544 T-carrier. Again, it doesn't matter technically, but it's nice to be precise wherever possible. Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=61521&t=61487 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Connecting WIC-1DSU? [7:61487]
You are correct. the 568A or B spec shows that pin 1 is tip and 2 is ring. Pin 4 is ring and pin 5 is tip for pair one. So for a tip to tip and ring to ring crossover then 2 to 4 and 1 to 5 is correct. > -Original Message- > From: s vermill [mailto:[EMAIL PROTECTED]] Also, it's interesting that > most people say 1 > to 4 and 2 to 5. I don't have a copy of any specs offhand, but it's > actually 1 to 5 and 2 to 4. Being bipolar though, it doesn't > matter. Ones > and zeros are signalled by the magnitude of difference > between the potential > at the A and B leads. In other words, current is caused to > flow or it's > not. Doesn't matter which direction. I'll see if I can dig > up something > official on the pins... Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=61516&t=61487 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Connecting WIC-1DSU? [7:61487]
s vermill wrote: > > Robert Perez wrote: > > > > yes you can do it. > > It uses pins 1,2 4,5. > > So you make a crossover cable with each pair > > 1 2 > > 2 1 > > > > 4 5 > > 5 4 > > > 1 & 2 to 4 & 5, not as above. Also, it's interesting that most > people say 1 to 4 and 2 to 5. I don't have a copy of any specs > offhand, but it's actually 1 to 5 and 2 to 4. Being bipolar > though, it doesn't matter. Ones and zeros are signalled by the > magnitude of difference between the potential at the A and B > leads. In other words, current is caused to flow or it's not. > Doesn't matter which direction. I'll see if I can dig up > something official on the pins... Well I admit that I didn't search very hard, but I couldn't find a USOC website that wasn't affiliated with the olypics. USOC defines the RJ set of connector bodies. Looking at several vendor pages, it would appear as if the consensus is that: Tip = 2 Ring = 1 and Tip1 = 5 Ring1 = 4 Making it 1 to 4 and 2 to 5. That being the case, I stand corrected. But again, it doesn't matter. There's no such thing as a tip/ring reversal on a T1 (sending junior techs to troubleshoot such problems used to be somewhat of a right-of-passage in certain circles). Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=61509&t=61487 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Connecting WIC-1DSU? [7:61487]
Robert Perez wrote: > > yes you can do it. > It uses pins 1,2 4,5. > So you make a crossover cable with each pair > 1 2 > 2 1 > > 4 5 > 5 4 > 1 & 2 to 4 & 5, not as above. Also, it's interesting that most people say 1 to 4 and 2 to 5. I don't have a copy of any specs offhand, but it's actually 1 to 5 and 2 to 4. Being bipolar though, it doesn't matter. Ones and zeros are signalled by the magnitude of difference between the potential at the A and B leads. In other words, current is caused to flow or it's not. Doesn't matter which direction. I'll see if I can dig up something official on the pins... Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=61508&t=61487 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Connecting WIC-1DSU? [7:61487]
Absolutely. In fact I'm currently doing just that beta testing version 2 of the WIC-1DSU-T1. You need a T1 xover cable. Dave Mike Mihalas wrote: > Is it possible to connect a WIC-1DSU-T1 to another WIC-1DSU-T1 to simulate a > circuit? I have two 2600's that I would like to connect to do some testing > with. If it is possible, do I need a special cable? > > Thanks in advance, > > Mike -- David Madland CCIE# 2016 Sr. Network Engineer Qwest Communications 612-664-3367 "You don't make the poor richer by making the rich poorer." --Winston Churchill Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=61503&t=61487 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Connecting WIC-1DSU? [7:61487]
yes you can do it. It uses pins 1,2 4,5. So you make a crossover cable with each pair 1 2 2 1 4 5 5 4 -Original Message- From: Mike Mihalas [mailto:[EMAIL PROTECTED]] Sent: Tuesday, January 21, 2003 2:32 PM To: [EMAIL PROTECTED] Subject: Connecting WIC-1DSU? [7:61487] Is it possible to connect a WIC-1DSU-T1 to another WIC-1DSU-T1 to simulate a circuit? I have two 2600's that I would like to connect to do some testing with. If it is possible, do I need a special cable? Thanks in advance, Mike Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=61502&t=61487 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Connecting WIC-1DSU? [7:61487]
you need a T1 crossover cable...I have one in my lab for the same thing you are trying to do... it works great for simulation of two routers with DS-1 connections... Larry Letterman Network Engineer Cisco Systems - Original Message - From: "Mike Mihalas" To: Sent: Tuesday, January 21, 2003 11:31 AM Subject: Connecting WIC-1DSU? [7:61487] > Is it possible to connect a WIC-1DSU-T1 to another WIC-1DSU-T1 to simulate a > circuit? I have two 2600's that I would like to connect to do some testing > with. If it is possible, do I need a special cable? > > Thanks in advance, > > Mike [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=61498&t=61487 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Connecting WIC-1DSU? [7:61487]
T-1 uses pins 1&2 and 4&5. Make a cable that crosses those two pairs. 1 to 4 2 to 5 4 to 1 5 to 2 If you don't have the tools to make a cable but do have two RJ-45 jacks - create the crossover between the jacks and use standard patch cables from the routers to the jacks. Yes, I know that a 110 punch down tool should be used with the jacks. Some small pliers, a small screwdriver and luck will also work for a lab - maybe not for a production network. > -Original Message- > From: Mike Mihalas [mailto:[EMAIL PROTECTED]] > Sent: Tuesday, January 21, 2003 1:32 PM > To: [EMAIL PROTECTED] > Subject: Connecting WIC-1DSU? [7:61487] > > > Is it possible to connect a WIC-1DSU-T1 to another > WIC-1DSU-T1 to simulate a > circuit? I have two 2600's that I would like to connect to do > some testing > with. If it is possible, do I need a special cable? > > Thanks in advance, > > Mike Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=61494&t=61487 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Connecting WIC-1DSU? [7:61487]
Mike Mihalas wrote: > > Is it possible to connect a WIC-1DSU-T1 to another WIC-1DSU-T1 > to simulate a circuit? I have two 2600's that I would like to > connect to do some testing with. If it is possible, do I need a > special cable? > > Thanks in advance, > > Mike Rollover cable: pins 1 & 2 to pins 4 & 5 and configure one of the WICs with: 'service-module t1 clock source internal' Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=61489&t=61487 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]