[Elecraft] K3XREF
Is the K3XREF, external clock interface, still offered as a product? I searched Elecraft but could not find any references to it. 73, phil, K7PEH __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] [K3XREF] Is not synchronizing
Hello Harald, It is probably best to repost this report to the list as there are many there far more knowledgeable about the K3 and what to expect, than me on it. With that, I am sending your reply directly to the list along with my reply to you. When I press Rev, I get no flashing XREV IN, it simply says XREV IN and then disappears after maybe one second. At that time it returns to REF CAL and within moments the asterisk is flashing. As I recall, initially it took a bit longer for the asterisk to appear, but it did and then it took some time for the REF CAL numerical readout to stabilize. Once stabilized I pushed A/B to save that value in memory. Write down your REF CAL number and then when you feel you have done all the right things, slowly turn VFO A and if you are locked in with the 10 MHz source, the letters REF CAL will be replaced with LOCKED. If this does not happen, return to the number you wrote down to return to where you were. Is it possible you do not have a working 10 MHz source? Is it possible either the connector or coax is not completing the connection? Is it possible the pins are not lined up properly in the K3XREF? At this point, I have no other ideas to help you, hopefully someone else can offer more. 73 & good luck, Gary KA1J > Hello Gary, > your assumption is correct. REV is pressed so that XREF IN is > flashing. > > But asterisk is not appearing :-( > > vy73 > Harald > DD0VS > > Gesendet: Freitag, 29. April 2016 um 22:57 Uhr > Von: "Gary Smith" > An: Elecraft@mailman.qth.net > Betreff: Re: [Elecraft] [K3XREF] Is not synchronizing > Assuming you > > 1. Have tech MD set as ON. > > 2. Are on REF CAL and waiting to see the flashing asterisk and not > seeing it: > > Then push the REV (2) button to be sure the k3xref is engaged. > > I'm guessing you might have missed that last step. If so, wait a > short while & hope for the asterisk between the REF CAL > > 73, > > Gary > KA1J > > > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to dd...@gmx.de __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] [K3XREF] Is not synchronizing
__ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] [K3XREF] Is not synchronizing
Assuming you 1. Have tech MD set as ON. 2. Are on REF CAL and waiting to see the flashing asterisk and not seeing it: Then push the REV (2) button to be sure the k3xref is engaged. I'm guessing you might have missed that last step. If so, wait a short while & hope for the asterisk between the REF CAL 73, Gary KA1J __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] [K3XREF] Is not synchronizing
__ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
[Elecraft] K3XREF
Hi there all, I am looking for a K3EXREF who has bought one and does not use it and is willing to sell.. Regards PE1BSB Netherlands -- Pe1bsb William lagerberg Stommeerkade 65 1431 EL Aalsmeer E will...@zendamateur.nl -- This email may contain confidential and privileged material for the sole use of the intended recepient. Any review or distribution by others is strictly prohibited. -- __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3XREF Question
Just to add some info to what Chuck, W7CS, wrote: I have both a Rubdidum and OCXO frequency standard in my shack. Here is a webpage that shows how I installed them: http://www.kl7uw.com/Rubidium.htm I run the OCXO as my 10-MHz reference for the K3 and VHF/UHF transverters (it is actually better than the Rb). I paid about $45 on e-bay for mine. It has run continuously since I installed it (about two years). Here is my beta test of the K3EXREF: http://www.kl7uw.com/K3EXREF.htm Hope this is helpful to those considering this topic. 73, Ed - KL7UW __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3XREF Question
On Wednesday Zilmer used a Straight-Key to send: -Original Comment--- > Hi Bob, > I use the Trimble Thunderbolt as a 10 MHz reference. <> > One thing you would want to set up different from the receiver's > defaults is the elevation mask. Hey, great info, thanks. I am getting one via Geo N4UA again, thanks! -- Best regards, Bob KD7YZWin7-64bit + K3 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3XREF Question
Yes. I have had the GPS system and also the Rubidium and other than seeing my HP counter with the oven controlled oscillator agree with them from time to time, I have to say it was pretty boring. Eventually both the standards broke and the HP is still with me. Chuck, KE9UW Lionel Trains, TCA, LCCA, LRRC aka Jack, BMW Motorcycles BMWMOA #224 From: elecraft-boun...@mailman.qth.net [elecraft-boun...@mailman.qth.net] on behalf of Chuck Smallhouse [w...@theriver.com] Sent: Thursday, February 14, 2013 6:18 PM To: Elecraft@mailman.qth.net Subject: [Elecraft] K3XREF Question Hi Don and All IMHO using a GPS disciplined 10 MHz (Trimble etc.) or a Rubidium standards are unnecessary , expensive and overly complicated approaches, to be used as the K3XREF 10 MHz external source. There are extremely stable (as high as 10 x-12th) Double Oven Controlled Xtal Oscillators (OCXOs) available on the Off Shore surplus market, for under $50 delivered. These are pulls from US built surplus equipment, and are guaranteed and tested . I have bought several, and the latest one has been bench tested for several months, and after initial adjustment has not varied a single cycle on my GPS locked counter. Even this stability, is an overkill, when used as an external reference for the "frequency", not "phase" locked K3. These OCXOs are less than 2" cube in size and available on e-Bay from several dealers. Check e-Bay under the subject OCXO. Chuck, W7CS __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] K3XREF Question
Hi Don and All IMHO using a GPS disciplined 10 MHz (Trimble etc.) or a Rubidium standards are unnecessary , expensive and overly complicated approaches, to be used as the K3XREF 10 MHz external source. There are extremely stable (as high as 10 x-12th) Double Oven Controlled Xtal Oscillators (OCXOs) available on the Off Shore surplus market, for under $50 delivered. These are pulls from US built surplus equipment, and are guaranteed and tested . I have bought several, and the latest one has been bench tested for several months, and after initial adjustment has not varied a single cycle on my GPS locked counter. Even this stability, is an overkill, when used as an external reference for the "frequency", not "phase" locked K3. These OCXOs are less than 2" cube in size and available on e-Bay from several dealers. Check e-Bay under the subject OCXO. Chuck, W7CS __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] K3XREF Question
KD7YZ Bob: Not your original question, but most are not aware that the common J-pole is a vertical polarized Zepp. I built a dual-band J-pole for 6m/10m and use a coax relay to switch feed selection for either band. No tuner required for the band segment I desired. Full description at: http://www.kl7uw.com/J-Pole.htm 73, Ed - KL7UW __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3XREF Question
Hi Bob, I use the Trimble Thunderbolt as a 10 MHz reference. This is a GPS disciplined clock, using GPS as the main time reference and an OCXO. The time and 10 MHz output are both very precise, in the 30 PPT range (though this precision varies, but not by even an order of magnitude). You can find the manual at http://trl.trimble.com/docushare/dsweb/Get/Document-10001/ThunderBoltBook2003.pdf. You will need to mount an outdoor GPS antenna. I use a Thales land surveying antenna and 40 feet of microwave coax. The receiver generally sees 8 channels with more than 40 dB C/No (which is a good signal for GPS). There are two software apps you may want to pick up: - Trimble's control program. This is used to set up parameters for the receiver. - Lady Heather's GPS Disciplined Oscillator program. This can be used to monitor the status of the receiver and signal levels, time, etc. graphically. One thing you would want to set up different from the receiver's defaults is the elevation mask. I believe the default is 5 degrees. I'd recommend 15 degrees. This tells the receiver not to use sats below the 15 deg "horizon". The lower in the sky a sat is, the noisier it is. Matt Zilmer, W6NIA -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of KD7YZ Bob Sent: Wednesday, February 13, 2013 4:56 AM To: K3 List Subject: [Elecraft] K3XREF Question Howdy K3' people: I have the K3XREF board and would like to get a device to use with it. What is suggested? And what external antenna goes with it? thanks -- 73 KD7YZ Bob __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3XREF Question
...remembering the advice about voltage levels. As far as I can see you can either use the ext ref continuously (which was my plan) or you can use it as a very handy way of re-calibrating the internal reference from time to time. - Stewart/G3YSX On 13/02/2013 13:16, Don Wilhelm wrote: Bob, You can use a 10 MHz Rubidium standard, or for even more accuracy, the Trimble Thunderbolt. The Thunderbolt requires a GPS antenna. 73, Don W3FPR On 2/13/2013 7:55 AM, KD7YZ Bob wrote: Howdy K3' people: I have the K3XREF board and would like to get a device to use with it. What is suggested? And what external antenna goes with it? thanks __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3XREF Question
Bob, You can use a 10 MHz Rubidium standard, or for even more accuracy, the Trimble Thunderbolt. The Thunderbolt requires a GPS antenna. 73, Don W3FPR On 2/13/2013 7:55 AM, KD7YZ Bob wrote: Howdy K3' people: I have the K3XREF board and would like to get a device to use with it. What is suggested? And what external antenna goes with it? thanks __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] K3XREF Question
Howdy K3' people: I have the K3XREF board and would like to get a device to use with it. What is suggested? And what external antenna goes with it? thanks -- 73 KD7YZ Bob __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html