[ewg] non SRQ patch for OFED 1.3
Some HCAs like ehca do not natively support srq. This patch would enable IPoIB
CM
for such HCAs. This patch has been accepted into Roland's for-2.6.25 git tree
for
about 3 months now.
Please consider including this patch into OFED 1.3.
Signed-off-by: Pradeep Satyanarayana <[EMAIL PROTECTED]>
---
--- a/drivers/infiniband/ulp/ipoib/ipoib.h 2008-01-23 13:29:06.0
-0800
+++ b/drivers/infiniband/ulp/ipoib/ipoib.h 2008-01-23 16:03:33.0
-0800
@@ -69,6 +69,7 @@ enum {
IPOIB_TX_RING_SIZE= 64,
IPOIB_MAX_QUEUE_SIZE = 8192,
IPOIB_MIN_QUEUE_SIZE = 2,
+ IPOIB_CM_MAX_CONN_QP = 4096,
IPOIB_NUM_WC = 4,
@@ -188,10 +189,13 @@ enum ipoib_cm_state {
struct ipoib_cm_rx {
struct ib_cm_id *id;
struct ib_qp*qp;
+ struct ipoib_cm_rx_buf *rx_ring;
struct list_head list;
struct net_device *dev;
unsigned longjiffies;
enum ipoib_cm_state state;
+ int index;
+ int recv_count;
};
struct ipoib_cm_tx {
@@ -234,6 +238,7 @@ struct ipoib_cm_dev_priv {
struct ib_wcibwc[IPOIB_NUM_WC];
struct ib_sge rx_sge[IPOIB_CM_RX_SG];
struct ib_recv_wr rx_wr;
+ int nonsrq_conn_qp;
int max_cm_mtu;
int num_frags;
};
@@ -463,6 +468,8 @@ void ipoib_drain_cq(struct net_device *d
/* We don't support UC connections at the moment */
#define IPOIB_CM_SUPPORTED(ha) (ha[0] & (IPOIB_FLAGS_RC))
+extern int ipoib_max_conn_qp;
+
static inline int ipoib_cm_admin_enabled(struct net_device *dev)
{
struct ipoib_dev_priv *priv = netdev_priv(dev);
@@ -493,6 +500,12 @@ static inline void ipoib_cm_set(struct i
neigh->cm = tx;
}
+static inline int ipoib_cm_has_srq(struct net_device *dev)
+{
+ struct ipoib_dev_priv *priv = netdev_priv(dev);
+ return !!priv->cm.srq;
+}
+
void ipoib_cm_send(struct net_device *dev, struct sk_buff *skb, struct
ipoib_cm_tx *tx);
int ipoib_cm_dev_open(struct net_device *dev);
void ipoib_cm_dev_stop(struct net_device *dev);
@@ -510,6 +523,8 @@ void ipoib_cm_handle_tx_wc(struct net_de
struct ipoib_cm_tx;
+#define ipoib_max_conn_qp 0
+
static inline int ipoib_cm_admin_enabled(struct net_device *dev)
{
return 0;
@@ -535,6 +550,11 @@ static inline void ipoib_cm_set(struct i
{
}
+static inline int ipoib_cm_has_srq(struct net_device *dev)
+{
+ return 0;
+}
+
static inline
void ipoib_cm_send(struct net_device *dev, struct sk_buff *skb, struct
ipoib_cm_tx *tx)
{
--- a/drivers/infiniband/ulp/ipoib/ipoib_cm.c 2008-01-23 13:29:06.0
-0800
+++ b/drivers/infiniband/ulp/ipoib/ipoib_cm.c 2008-01-23 16:46:47.0
-0800
@@ -39,6 +39,13 @@
#include
#include
+int ipoib_max_conn_qp = 128;
+
+module_param_named(max_nonsrq_conn_qp, ipoib_max_conn_qp, int, 0444);
+MODULE_PARM_DESC(max_nonsrq_conn_qp,
+"Max number of connected-mode QPs per interface "
+"(applied only if shared receive queue is not available)");
+
#ifdef CONFIG_INFINIBAND_IPOIB_DEBUG_DATA
static int data_debug_level;
@@ -81,7 +88,7 @@ static void ipoib_cm_dma_unmap_rx(struct
ib_dma_unmap_single(priv->ca, mapping[i + 1], PAGE_SIZE,
DMA_FROM_DEVICE);
}
-static int ipoib_cm_post_receive(struct net_device *dev, int id)
+static int ipoib_cm_post_receive_srq(struct net_device *dev, int id)
{
struct ipoib_dev_priv *priv = netdev_priv(dev);
struct ib_recv_wr *bad_wr;
@@ -104,7 +111,33 @@ static int ipoib_cm_post_receive(struct
return ret;
}
-static struct sk_buff *ipoib_cm_alloc_rx_skb(struct net_device *dev, int id,
int frags,
+static int ipoib_cm_post_receive_nonsrq(struct net_device *dev,
+ struct ipoib_cm_rx *rx, int id)
+{
+ struct ipoib_dev_priv *priv = netdev_priv(dev);
+ struct ib_recv_wr *bad_wr;
+ int i, ret;
+
+ priv->cm.rx_wr.wr_id = id | IPOIB_OP_CM | IPOIB_OP_RECV;
+
+ for (i = 0; i < IPOIB_CM_RX_SG; ++i)
+ priv->cm.rx_sge[i].addr = rx->rx_ring[id].mapping[i];
+
+ ret = ib_post_recv(rx->qp, &priv->cm.rx_wr, &bad_wr);
+ if (unlikely(ret)) {
+ ipoib_warn(priv, "post recv failed for buf %d (%d)\n", id, ret);
+ ipoib_cm_dma_unmap_rx(priv, IPOIB_CM_RX_SG - 1,
+ rx->rx_ring[id].mapping);
+ dev_kfree_skb_any(rx->rx_ring[id].skb);
+ rx->rx_ring[id].skb = NULL;
+ }
+
+ return ret;
+}
+
+static struct sk_buff *ipoib_cm_alloc_rx_skb(struct net_device *dev,
+struct ipoib_cm_rx_buf *rx_ring,
+int id, int frags,
u64 mapping[IPOIB_CM_RX_SG])
{
[ewg] Re: [ofa-general] [PATCH] IB/ehca: Prevent sending UD packets to QP0
On Thu, 2008-01-24 at 17:59 +0100, Joachim Fenkes wrote:
> IB spec doesn't allow packets to QP0 sent on any other VL than VL15.
> Hardware doesn't filter those packets on the send side, so we need to do
> this in the driver and firmware.
>
> As eHCA doesn't support QP0, we can just filter out all traffic going to
> QP0, regardless of SL or VL.
Is this a hardware or software limitation ? If it is software, is there
any plan to enable QP0 support ?
-- Hal
> Signed-off-by: Joachim Fenkes <[EMAIL PROTECTED]>
> ---
> drivers/infiniband/hw/ehca/ehca_reqs.c |4
> 1 files changed, 4 insertions(+), 0 deletions(-)
>
> diff --git a/drivers/infiniband/hw/ehca/ehca_reqs.c
> b/drivers/infiniband/hw/ehca/ehca_reqs.c
> index 3aacc8c..2ce8cff 100644
> --- a/drivers/infiniband/hw/ehca/ehca_reqs.c
> +++ b/drivers/infiniband/hw/ehca/ehca_reqs.c
> @@ -209,6 +209,10 @@ static inline int ehca_write_swqe(struct ehca_qp *qp,
> ehca_gen_err("wr.ud.ah is NULL. qp=%p", qp);
> return -EINVAL;
> }
> + if (unlikely(send_wr->wr.ud.remote_qpn == 0)) {
> + ehca_gen_err("dest QP# is 0. qp=%x", qp->real_qp_num);
> + return -EINVAL;
> + }
> my_av = container_of(send_wr->wr.ud.ah, struct ehca_av, ib_ah);
> wqe_p->u.ud_av.ud_av = my_av->av;
>
___
ewg mailing list
ewg@lists.openfabrics.org
http://lists.openfabrics.org/cgi-bin/mailman/listinfo/ewg
[ewg] [GIT PULL ofed-1.3] - Tag the ofed cxgb3 driver version.
Vlad, Please pull the following patch from: git://git.openfabrics.org/~swise/ofed-1.3 ofed_kernel This patch must have gotten lost from 1.2.5 -> 1.3. Thanks, Steve. - Tag -ofed for cxgb3 driver version. This keeps kernel.org vs ofed driver versions unique. Signed-off-by: Steve Wise <[EMAIL PROTECTED]> --- .../fixes/cxgb3_00300_add_ofed_version_tag.patch | 13 + 1 files changed, 13 insertions(+), 0 deletions(-) diff --git a/kernel_patches/fixes/cxgb3_00300_add_ofed_version_tag.patch b/kernel_patches/fixes/cxgb3_00300_add_ofed_version_tag.patch new file mode 100644 index 000..ffee40a --- /dev/null +++ b/kernel_patches/fixes/cxgb3_00300_add_ofed_version_tag.patch @@ -0,0 +1,13 @@ +diff --git a/drivers/net/cxgb3/version.h b/drivers/net/cxgb3/version.h +index ef1c633..ef2405a 100644 +--- a/drivers/net/cxgb3/version.h b/drivers/net/cxgb3/version.h +@@ -35,7 +35,7 @@ + #define DRV_DESC "Chelsio T3 Network Driver" + #define DRV_NAME "cxgb3" + /* Driver version */ +-#define DRV_VERSION "1.0-ko" ++#define DRV_VERSION "1.0-ofed" + + /* Firmware version */ + #define FW_VERSION_MAJOR 4 ___ ewg mailing list ewg@lists.openfabrics.org http://lists.openfabrics.org/cgi-bin/mailman/listinfo/ewg
RE: [ofa-general] RE: [ewg] Not seeing any SDP performance changes inOFED 1.3 beta, and I get Oops when enabling sdp_zcopy_thresh
I've tested on RHEL4 and RHEL5, and see no sdp_zcopy_thresh improvement for any message size, as measured with netperf, for any Arbel or ConnectX HCA. Scott > -Original Message- > From: Jim Mott [mailto:[EMAIL PROTECTED] > Sent: Thursday, January 24, 2008 7:57 AM > To: Weikuan Yu; Scott Weitzenkamp (sweitzen) > Cc: ewg@lists.openfabrics.org; [EMAIL PROTECTED] > Subject: RE: [ofa-general] RE: [ewg] Not seeing any SDP > performance changes inOFED 1.3 beta, and I get Oops when > enabling sdp_zcopy_thresh > > Hi, > 64K is borderline for seeing bzcopy effect. Using an AMD > 6000+ (3 Ghz > dual core) in Asus M2A-VM motherboard with ConnectX running > 2.3 firmware > and OFED 1.3-rc3 stack running on 2.6.23.8 kernel.org kernel, > I ran the > test for 128K: > 5546 sdp_zcopy_thresh=0 (off) > 8709 sdp_zcopy_thresh=65536 > > For these tests, I just have LD_PRELOAD set in my environment. > > === > > I see that TCP_MAXSEG is not being handled by libsdp and will > look into > it. > > > [EMAIL PROTECTED] ~]# modprobe ib_sdp > [EMAIL PROTECTED] ~]# netperf -v2 -4 -H 193.168.10.198 -l 30 -t TCP_STREAM -c > -C -- -m 128K > TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to > 193.168.10.198 > (193.168.10.198) port 0 AF_INET > netperf: get_tcp_info: getsockopt TCP_MAXSEG: errno 92 > Recv SendSend Utilization Service > Demand > Socket Socket Message Elapsed Send Recv Send > Recv > Size SizeSize Time Throughput localremote local > remote > bytes bytes bytessecs.10^6bits/s % S % S us/KB > us/KB > > 87380 16384 13107230.01 5545.69 51.4714.431.521 > 1.706 > > Alignment Offset BytesBytes Sends Bytes > Recvs > Local Remote Local Remote Xfered Per Per > Send RecvSend Recv Send (avg) Recv (avg) > 8 8 0 0 2.08e+10 131072.00158690 33135.60 > 627718 > > Maximum > Segment > Size (bytes) > -1 > [EMAIL PROTECTED] ~]# echo 65536 > >/sys/module/ib_sdp/parameters/sdp_zcopy_thresh > [EMAIL PROTECTED] ~]# netperf -v2 -4 -H 193.168.10.198 -l 30 -t TCP_STREAM -c > -C -- -m 128K > TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to > 193.168.10.198 > (193.168.10.198) port 0 AF_INET > netperf: get_tcp_info: getsockopt TCP_MAXSEG: errno 92 > Recv SendSend Utilization Service > Demand > Socket Socket Message Elapsed Send Recv Send > Recv > Size SizeSize Time Throughput localremote local > remote > bytes bytes bytessecs.10^6bits/s % S % S us/KB > us/KB > > 87380 16384 13107230.01 8708.58 50.6314.550.953 > 1.095 > > Alignment Offset BytesBytes Sends Bytes > Recvs > Local Remote Local Remote Xfered Per Per > Send RecvSend Recv Send (avg) Recv (avg) > 8 8 0 0 3.267e+10 131072.00249228 26348.30 > 1239807 > > Maximum > Segment > Size (bytes) > -1 > > Thanks, > JIm > > Jim Mott > Mellanox Technologies Ltd. > mail: [EMAIL PROTECTED] > Phone: 512-294-5481 > > > -Original Message- > From: Weikuan Yu [mailto:[EMAIL PROTECTED] > Sent: Thursday, January 24, 2008 9:09 AM > To: Scott Weitzenkamp (sweitzen) > Cc: Jim Mott; ewg@lists.openfabrics.org; [EMAIL PROTECTED] > Subject: Re: [ofa-general] RE: [ewg] Not seeing any SDP performance > changes inOFED 1.3 beta, and I get Oops when enabling sdp_zcopy_thresh > > Hi, Scott, > > I have been running SDP tests across two woodcrest nodes with 4x DDR > cards using OFED-1.2.5.4. The card/firmware info is below. > > CA 'mthca0' > CA type: MT25208 > Number of ports: 2 > Firmware version: 5.1.400 > Hardware version: a0 > Node GUID: 0x0002c90200228e0c > System image GUID: 0x0002c90200228e0f > > I could not get a bandwidth more than 5Gbps like you have shown here. > Wonder if I need to upgrade to the latest software or firmware? Any > suggestions? > > Thanks, > --Weikuan > > > TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to > 192.168.225.77 > (192.168 > .225.77) port 0 AF_INET > Recv SendSend Utilization > Service > Demand > Socket Socket Message Elapsed Send Recv Send > Recv > Size SizeSize Time Throughput localremote local > remote > bytes bytes bytessecs.10^6bits/s % S % S us/KB > us/KB > > 131072 131072 13107210.00 4918.95 21.2924.991.418 > 1.665 > > > Scott Weitzenkamp (sweitzen) wrote: > > Jim, > > > > I am trying OFED-1.3-20071231-0600 and RHEL4 x86_64 on a dual CPU > > (single core each CPU) Xeon system. I do not see any performance > > improvement (either throughput or CPU ut
[ewg] [PATCH] IB/ehca: Prevent sending UD packets to QP0
IB spec doesn't allow packets to QP0 sent on any other VL than VL15.
Hardware doesn't filter those packets on the send side, so we need to do
this in the driver and firmware.
As eHCA doesn't support QP0, we can just filter out all traffic going to
QP0, regardless of SL or VL.
Signed-off-by: Joachim Fenkes <[EMAIL PROTECTED]>
---
drivers/infiniband/hw/ehca/ehca_reqs.c |4
1 files changed, 4 insertions(+), 0 deletions(-)
diff --git a/drivers/infiniband/hw/ehca/ehca_reqs.c
b/drivers/infiniband/hw/ehca/ehca_reqs.c
index 3aacc8c..2ce8cff 100644
--- a/drivers/infiniband/hw/ehca/ehca_reqs.c
+++ b/drivers/infiniband/hw/ehca/ehca_reqs.c
@@ -209,6 +209,10 @@ static inline int ehca_write_swqe(struct ehca_qp *qp,
ehca_gen_err("wr.ud.ah is NULL. qp=%p", qp);
return -EINVAL;
}
+ if (unlikely(send_wr->wr.ud.remote_qpn == 0)) {
+ ehca_gen_err("dest QP# is 0. qp=%x", qp->real_qp_num);
+ return -EINVAL;
+ }
my_av = container_of(send_wr->wr.ud.ah, struct ehca_av, ib_ah);
wqe_p->u.ud_av.ud_av = my_av->av;
--
1.5.2
___
ewg mailing list
ewg@lists.openfabrics.org
http://lists.openfabrics.org/cgi-bin/mailman/listinfo/ewg
RE: [ofa-general] RE: [ewg] Not seeing any SDP performance changes inOFED 1.3 beta, and I get Oops when enabling sdp_zcopy_thresh
Hi, 64K is borderline for seeing bzcopy effect. Using an AMD 6000+ (3 Ghz dual core) in Asus M2A-VM motherboard with ConnectX running 2.3 firmware and OFED 1.3-rc3 stack running on 2.6.23.8 kernel.org kernel, I ran the test for 128K: 5546 sdp_zcopy_thresh=0 (off) 8709 sdp_zcopy_thresh=65536 For these tests, I just have LD_PRELOAD set in my environment. === I see that TCP_MAXSEG is not being handled by libsdp and will look into it. [EMAIL PROTECTED] ~]# modprobe ib_sdp [EMAIL PROTECTED] ~]# netperf -v2 -4 -H 193.168.10.198 -l 30 -t TCP_STREAM -c -C -- -m 128K TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 193.168.10.198 (193.168.10.198) port 0 AF_INET netperf: get_tcp_info: getsockopt TCP_MAXSEG: errno 92 Recv SendSend Utilization Service Demand Socket Socket Message Elapsed Send Recv Send Recv Size SizeSize Time Throughput localremote local remote bytes bytes bytessecs.10^6bits/s % S % S us/KB us/KB 87380 16384 13107230.01 5545.69 51.4714.431.521 1.706 Alignment Offset BytesBytes Sends Bytes Recvs Local Remote Local Remote Xfered Per Per Send RecvSend Recv Send (avg) Recv (avg) 8 8 0 0 2.08e+10 131072.00158690 33135.60 627718 Maximum Segment Size (bytes) -1 [EMAIL PROTECTED] ~]# echo 65536 >/sys/module/ib_sdp/parameters/sdp_zcopy_thresh [EMAIL PROTECTED] ~]# netperf -v2 -4 -H 193.168.10.198 -l 30 -t TCP_STREAM -c -C -- -m 128K TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 193.168.10.198 (193.168.10.198) port 0 AF_INET netperf: get_tcp_info: getsockopt TCP_MAXSEG: errno 92 Recv SendSend Utilization Service Demand Socket Socket Message Elapsed Send Recv Send Recv Size SizeSize Time Throughput localremote local remote bytes bytes bytessecs.10^6bits/s % S % S us/KB us/KB 87380 16384 13107230.01 8708.58 50.6314.550.953 1.095 Alignment Offset BytesBytes Sends Bytes Recvs Local Remote Local Remote Xfered Per Per Send RecvSend Recv Send (avg) Recv (avg) 8 8 0 0 3.267e+10 131072.00249228 26348.30 1239807 Maximum Segment Size (bytes) -1 Thanks, JIm Jim Mott Mellanox Technologies Ltd. mail: [EMAIL PROTECTED] Phone: 512-294-5481 -Original Message- From: Weikuan Yu [mailto:[EMAIL PROTECTED] Sent: Thursday, January 24, 2008 9:09 AM To: Scott Weitzenkamp (sweitzen) Cc: Jim Mott; ewg@lists.openfabrics.org; [EMAIL PROTECTED] Subject: Re: [ofa-general] RE: [ewg] Not seeing any SDP performance changes inOFED 1.3 beta, and I get Oops when enabling sdp_zcopy_thresh Hi, Scott, I have been running SDP tests across two woodcrest nodes with 4x DDR cards using OFED-1.2.5.4. The card/firmware info is below. CA 'mthca0' CA type: MT25208 Number of ports: 2 Firmware version: 5.1.400 Hardware version: a0 Node GUID: 0x0002c90200228e0c System image GUID: 0x0002c90200228e0f I could not get a bandwidth more than 5Gbps like you have shown here. Wonder if I need to upgrade to the latest software or firmware? Any suggestions? Thanks, --Weikuan TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.225.77 (192.168 .225.77) port 0 AF_INET Recv SendSend Utilization Service Demand Socket Socket Message Elapsed Send Recv Send Recv Size SizeSize Time Throughput localremote local remote bytes bytes bytessecs.10^6bits/s % S % S us/KB us/KB 131072 131072 13107210.00 4918.95 21.2924.991.418 1.665 Scott Weitzenkamp (sweitzen) wrote: > Jim, > > I am trying OFED-1.3-20071231-0600 and RHEL4 x86_64 on a dual CPU > (single core each CPU) Xeon system. I do not see any performance > improvement (either throughput or CPU utilization) using netperf when I > set /sys/module/ib_sdp/sdp_zcopy_thresh to 16384. Can you elaborate on > your HCA type, and performance improvement you see? > > Here's an example netperf command line when using a Cheetah DDR HCA and > 1.2.917 firmware (I have also tried ConnectX and 2.3.000 firmware too): > > [EMAIL PROTECTED] ~]$ LD_PRELOAD=libsdp.so netperf241 -v2 -4 -H > 192.168.1.201 -l 30 -t TCP_STREAM -c -C -- -m 65536 > TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.1.201 > (192.168.1.201) port 0 AF_INET : histogram : demo > > Recv SendSend Utilization Service > Demand > Socket Socket Message Elapsed Send Recv Send > Recv > Size SizeSize Time Throughput localremote local > remote > bytes bytes b
Re: [ofa-general] RE: [ewg] Not seeing any SDP performance changes inOFED 1.3 beta, and I get Oops when enabling sdp_zcopy_thresh
Hi, Scott, I have been running SDP tests across two woodcrest nodes with 4x DDR cards using OFED-1.2.5.4. The card/firmware info is below. CA 'mthca0' CA type: MT25208 Number of ports: 2 Firmware version: 5.1.400 Hardware version: a0 Node GUID: 0x0002c90200228e0c System image GUID: 0x0002c90200228e0f I could not get a bandwidth more than 5Gbps like you have shown here. Wonder if I need to upgrade to the latest software or firmware? Any suggestions? Thanks, --Weikuan TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.225.77 (192.168 .225.77) port 0 AF_INET Recv SendSend Utilization Service Demand Socket Socket Message Elapsed Send Recv SendRecv Size SizeSize Time Throughput localremote local remote bytes bytes bytessecs.10^6bits/s % S % S us/KB us/KB 131072 131072 13107210.00 4918.95 21.2924.991.418 1.665 Scott Weitzenkamp (sweitzen) wrote: Jim, I am trying OFED-1.3-20071231-0600 and RHEL4 x86_64 on a dual CPU (single core each CPU) Xeon system. I do not see any performance improvement (either throughput or CPU utilization) using netperf when I set /sys/module/ib_sdp/sdp_zcopy_thresh to 16384. Can you elaborate on your HCA type, and performance improvement you see? Here's an example netperf command line when using a Cheetah DDR HCA and 1.2.917 firmware (I have also tried ConnectX and 2.3.000 firmware too): [EMAIL PROTECTED] ~]$ LD_PRELOAD=libsdp.so netperf241 -v2 -4 -H 192.168.1.201 -l 30 -t TCP_STREAM -c -C -- -m 65536 TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.1.201 (192.168.1.201) port 0 AF_INET : histogram : demo Recv SendSend Utilization Service Demand Socket Socket Message Elapsed Send Recv Send Recv Size SizeSize Time Throughput localremote local remote bytes bytes bytessecs.10^6bits/s % S % S us/KB us/KB 87380 16384 6553630.01 7267.70 55.0661.271.241 1.381 Alignment Offset BytesBytes Sends Bytes Recvs Local Remote Local Remote Xfered Per Per Send RecvSend Recv Send (avg) Recv (avg) 8 8 0 0 2.726e+10 65536.00415942 48106.01 566648 ___ ewg mailing list ewg@lists.openfabrics.org http://lists.openfabrics.org/cgi-bin/mailman/listinfo/ewg
[ewg] ib-bonding release 22
Please take from my home dir. latest.txt was also updated.
Change Log:
--
1. Apply backport patches also for kernel 2.6.9-67 (Redhat4 UP6)
2. Fix bugs for working with OS tools (sysconfig/initscripts)
3. Change in documentation for working with OS tools
4. Fix: in ib-bons - bond0 appears as constant instead of $BOND_NAME in one
place
5. Fix: Destroy bonding master only if it exists
Vlad,
Please apply the patch below to ofed_1_3_scripts to complete the support for
RH4 Up6
Add 2.6.9-67 to the list of kernels that are supported by ib-bonding
Signed-off-by: Moni Shoua <[EMAIL PROTECTED]>
---
diff --git a/install.pl b/install.pl
index 256263d..fcae1fb 100755
--- a/install.pl
+++ b/install.pl
@@ -1579,7 +1579,7 @@ sub set_availability
}
# ib-bonding
-if ($kernel =~
m/2.6.9-34|2.6.9-42|2.6.9-55|2.6.16.[0-9.]*-[0-9.]*-[A-Za-z0-9.]*|el5|fc6/) {
+if ($kernel =~
m/2.6.9-34|2.6.9-42|2.6.9-55|2.6.9-67|2.6.16.[0-9.]*-[0-9.]*-[A-Za-z0-9.]*|el5|fc6/)
{
$packages_info{'ib-bonding'}{'available'} = 1;
$packages_info{'ib-bonding-debuginfo'}{'available'} = 1;
}
___
ewg mailing list
ewg@lists.openfabrics.org
http://lists.openfabrics.org/cgi-bin/mailman/listinfo/ewg
