Re: [Flexradio] Using a Behringher Xenyx 802 mixer with SDR1K and other dramas
My setup : SDR1k with 100 W PA, M-Audio Delta 44, Delta 44 interface designed by Eric, AA4SW and Tony KB9YIG. This board replaces the M-Audio breakout box. It is screwed directly on the D44 connector, Poor man UCB board designed by M0ZAZ, fitted on the X2 connector (back of the SDR), for amplifier switching, Heil PR40 with Behringher UB802. One of the ancient cables supplied with the D44 goes from L and R Main out of the Behringher to the Mic in connector of the Eric/Tony interface. On the console, CPDR at 1, Mic gain at 10. Preamplification is given by the UB802. Equalizer adjusted on the UB802, not on the console. Now using svn 682, but I test all Alpha versions. Conclusion : very satisfied by comments received. 73, José F5JD inspections a écrit : I've finally got my SDR1K working again after a 2 month break due to rf problems/ no time/ antennas stuffed etc !! I still have a drama whereby it often doesnt actually receive unless I switch it off/on several times and go in and out of the software etc, like it has always had, but now it also shows the wrong signal on the wrong frequency. By that I mean I can be listening to an am station on 720 khz and then tune up the freq by 2-3 mhz and still be receiving the am station , that one puzzles me. And I've given up on the USB adapter cable, just too unreliable. However the reason for this email is I now use an NCS 3240 Multi switcher between my Heil HM10 and Heil iC pro headset and my SDR1K, Tentec OmniVI, Icom IC910 and Yeasu Ft 8900. I decided the SDR would go through a Behringher 802 mixer to play around with the audio. I have the correct lead from the NCS to the mixer supplied by NCS , and made up a straight unbalanced mono 1/4 jack plug lead from the output of the mixer to the input of the Delta 44 breakout box input 3. Both mic's work well with all the other radios, but so far I have no output from the SDR/Behringher combination, even after playing around with settings on the mixer and powersdr for hours ! I know there are those of you out there who have tried similar combinations and was wondering if anyone can advise me please ? I really like my SDR1K , when it works, but for some reason it just seems to have a mind of its own!! BTW I am now running SVN681 and this seems to be the most success I've ever had. Since I bought the radio in Feb this year I've managed only 2 qso's without things tripping, dropping out or switching off on their own, mostly due to a poor earth system which has now been rectified. I wish it would work reliably, or I could find out what I'm doing wrong , which is more likely !! Thanks folks 73 de Keith VK6XH ___ FlexRadio mailing list FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archive Link: http://www.mail-archive.com/flexradio%40flex-radio.biz/ FlexRadio Homepage: http://www.flex-radio.com
[Flexradio] Using a Behringher Xenyx 802 mixer with SDR1K and other dramas
I've finally got my SDR1K working again after a 2 month break due to rf problems/ no time/ antennas stuffed etc !! I still have a drama whereby it often doesnt actually receive unless I switch it off/on several times and go in and out of the software etc, like it has always had, but now it also shows the wrong signal on the wrong frequency. By that I mean I can be listening to an am station on 720 khz and then tune up the freq by 2-3 mhz and still be receiving the am station , that one puzzles me. And I've given up on the USB adapter cable, just too unreliable. However the reason for this email is I now use an NCS 3240 Multi switcher between my Heil HM10 and Heil iC pro headset and my SDR1K, Tentec OmniVI, Icom IC910 and Yeasu Ft 8900. I decided the SDR would go through a Behringher 802 mixer to play around with the audio. I have the correct lead from the NCS to the mixer supplied by NCS , and made up a straight unbalanced mono 1/4 jack plug lead from the output of the mixer to the input of the Delta 44 breakout box input 3. Both mic's work well with all the other radios, but so far I have no output from the SDR/Behringher combination, even after playing around with settings on the mixer and powersdr for hours ! I know there are those of you out there who have tried similar combinations and was wondering if anyone can advise me please ? I really like my SDR1K , when it works, but for some reason it just seems to have a mind of its own!! BTW I am now running SVN681 and this seems to be the most success I've ever had. Since I bought the radio in Feb this year I've managed only 2 qso's without things tripping, dropping out or switching off on their own, mostly due to a poor earth system which has now been rectified. I wish it would work reliably, or I could find out what I'm doing wrong , which is more likely !! Thanks folks 73 de Keith VK6XH -- Keith Bainbridge Air Receiver Inspection Services Unfired Pressure Vessel Inspections Worksafe WA Vessel Registrations. Safety Relief Valve Repairs. Mob: 0419 901 539 Fax: 08 9379 3423 A/Hours 08 9279 4923 Email[EMAIL PROTECTED] My career goal is to retire. ___ FlexRadio mailing list FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archive Link: http://www.mail-archive.com/flexradio%40flex-radio.biz/ FlexRadio Homepage: http://www.flex-radio.com
Re: [Flexradio] Using a Behringher Xenyx 802 mixer with SDR1K and other dramas
I had similar problems so I switched back to 6.1.2. Now everything is really good. Wait till they officially release 6.1.3. It should be fine then too. inspections [EMAIL PROTECTED] wrote: I've finally got my SDR1K working again after a 2 month break due to rf problems/ no time/ antennas stuffed etc !! I still have a drama whereby it often doesnt actually receive unless I switch it off/on several times and go in and out of the software etc, like it has always had, but now it also shows the wrong signal on the wrong frequency. By that I mean I can be listening to an am station on 720 khz and then tune up the freq by 2-3 mhz and still be receiving the am station , that one puzzles me. And I've given up on the USB adapter cable, just too unreliable. However the reason for this email is I now use an NCS 3240 Multi switcher between my Heil HM10 and Heil iC pro headset and my SDR1K, Tentec OmniVI, Icom IC910 and Yeasu Ft 8900. I decided the SDR would go through a Behringher 802 mixer to play around with the audio. I have the correct lead from the NCS to the mixer supplied by NCS , and made up a straight unbalanced mono 1/4 jack plug lead from the output of the mixer to the input of the Delta 44 breakout box input 3. Both mic's work well with all the other radios, but so far I have no output from the SDR/Behringher combination, even after playing around with settings on the mixer and powersdr for hours ! I know there are those of you out there who have tried similar combinations and was wondering if anyone can advise me please ? I really like my SDR1K , when it works, but for some reason it just seems to have a mind of its own!! BTW I am now running SVN681 and this seems to be the most success I've ever had. Since I bought the radio in Feb this year I've managed only 2 qso's without things tripping, dropping out or switching off on their own, mostly due to a poor earth system which has now been rectified. I wish it would work reliably, or I could find out what I'm doing wrong , which is more likely !! Thanks folks 73 de Keith VK6XH -- Keith Bainbridge Air Receiver Inspection Services Unfired Pressure Vessel Inspections Worksafe WA Vessel Registrations. Safety Relief Valve Repairs. Mob: 0419 901 539 Fax: 08 9379 3423 A/Hours 08 9279 4923 Email [EMAIL PROTECTED] My career goal is to retire. ___ FlexRadio mailing list FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archive Link: http://www.mail-archive.com/flexradio%40flex-radio.biz/ FlexRadio Homepage: http://www.flex-radio.com -- next part -- An HTML attachment was scrubbed... URL: /pipermail/flexradio_flex-radio.biz/attachments/20060918/cd635dce/attachment.html ___ FlexRadio mailing list FlexRadio@flex-radio.biz http://mail.flex-radio.biz/mailman/listinfo/flexradio_flex-radio.biz Archive Link: http://www.mail-archive.com/flexradio%40flex-radio.biz/ FlexRadio Homepage: http://www.flex-radio.com
