Re: Oops on arm pxa270 2.6.22
Mike Rapoport wrote: I think you have conflict between PXA serial and 8250 drivers. Make sure you use only one of them. If you need to use PCMCIA serial cards, please see http://lists.arm.linux.org.uk/pipermail/linux-arm-kernel/2007-July/040604.html Thanks, I already fixed my problem. You are right it was serial port problem. I had wrong MAJOR and MINOR numbers in serial/pxa.c Now kerel boots and works fine with -ck patch. My I ask you if you (compulab) have any plans of merging machine cm-x270 patches into mainline kernel. Thanks again, Rok Markovic - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
Re: Oops on arm pxa270 2.6.22
Rok Markovic wrote: Hi I would like to ask what could be a problem or how could I start debuging it. My board is cm-x270 from compulab and it successfully boot until it should start init from busysbox. I get the folowing report. environment: pxa270 128Mb RAM network boot gcc 3.4.5 softfloat Linux image detected in memory at 0xA010, booting... [snip] pxa2xx-fb: probe of pxa2xx-fb failed with error -22 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [snip] RAMDISK driver initialized: 4 RAM disks of 4096K size 1024 blocksize bootserver=0.0.0.0, rootserver=192.168.10.124, rootpath= Looking up port of RPC 13/2 on 192.168.10.124 Looking up port of RPC 15/1 on 192.168.10.124 VFS: Mounted root (nfs filesystem). Freeing init memory: 108K Unable to handle kernel NULL pointer dereference at virtual address 0004 pgd = c0004000 [0004] *pgd= Internal error: Oops: f5 [#1] Modules linked in: CPU: 0Not tainted (2.6.22-cm-x270 #2) PC is at init_dev+0x38/0x5b8 LR is at tty_open+0xf8/0x33c pc : []lr : []psr: 6013 [snip] 3fe0: c0423ff8 c003c9e8 c0008b30 e1a01007 ebfd4ec0 Backtrace: [] (init_dev+0x0/0x5b8) from [] (tty_open+0xf8/0x33c) [] (tty_open+0x0/0x33c) from [] (chrdev_open+0x114/0x174) r8:c04e0d20 r7: r6: r5:c048f76c r4:c02e5c3c [] (chrdev_open+0x0/0x174) from [] (__dentry_open+0x188/0x228) r8:c0531c80 r7:c04ae364 r6:c00884ec r5:c048f76c r4:c04e0d20 [] (__dentry_open+0x0/0x228) from [] (nameidata_to_filp+0x34/0x4c) [] (nameidata_to_filp+0x0/0x4c) from [] (do_filp_open+0x4c/0x50) r4:0002 [] (do_filp_open+0x0/0x50) from [] (do_sys_open+0x5c/0xec) r5: r4:0002 [] (do_sys_open+0x0/0xec) from [] (sys_open+0x24/0x28) [] (sys_open+0x0/0x28) from [] (init_post+0x2c/0xfc) [] (init_post+0x0/0xfc) from [] (kernel_init+0x15c/0x2bc) r4:c02afed8 [] (kernel_init+0x0/0x2bc) from [] (do_exit+0x0/0x86c) Code: e3a03000 e5823000 059030b8 e1a06000 (07935107) Kernel panic - not syncing: Attempted to kill init! I think you have conflict between PXA serial and 8250 drivers. Make sure you use only one of them. If you need to use PCMCIA serial cards, please see http://lists.arm.linux.org.uk/pipermail/linux-arm-kernel/2007-July/040604.html -- Sincerely yours, Mike. - To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
Oops on arm pxa270 2.6.22
Hi I would like to ask what could be a problem or how could I start debuging it. My board is cm-x270 from compulab and it successfully boot until it should start init from busysbox. I get the folowing report. environment: pxa270 128Mb RAM network boot gcc 3.4.5 softfloat Linux image detected in memory at 0xA010, booting... Kernel parameters: root=/dev/nfs ip=:eth0: console=ttySA1,38400N1 bpp=16 nfsroot=192.168.10.124:/cm-x270 KERNEL_PARAMS: 0xA100 Linux version 2.6.22-cm-x270 ([EMAIL PROTECTED]) (gcc version 3.4.5) #2 Thu Jul 19 09:54:50 CEST 2007 CPU: XScale-PXA270 [69054117] revision 7 (ARMv5TE), cr=397f Machine: Compulab CM-x270 ATAG_INITRD is deprecated; please update your bootloader. Memory policy: ECC disabled, Data cache writeback Run Mode clock: 208.00MHz (*16) Turbo Mode clock: 520.00MHz (*2.5, active) Memory clock: 208.00MHz (/2) System bus clock: 208.00MHz CPU0: D VIVT undefined 5 cache CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets Built 1 zonelists. Total pages: 32512 Kernel command line: root=/dev/nfs ip=:eth0: console=ttySA1,38400N1 bpp=16 nfsroot=192.168.10.124:/cm-x270 PID hash table entries: 512 (order: 9, 2048 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 128MB = 128MB total Memory: 126848KB available (2492K code, 371K data, 108K init) SLUB: Genslabs=22, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Time: pxa_timer clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NetWinder Floating Point Emulator V0.97 (double precision) io scheduler noop registered io scheduler cfq registered (default) pxa2xx-fb pxa2xx-fb: Invalid resolution or bit depth pxa2xx-fb: probe of pxa2xx-fb failed with error -22 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled RAMDISK driver initialized: 4 RAM disks of 4096K size 1024 blocksize loop: module loaded dm9000 Ethernet Driver eth0: dm9000 at c8802000,c8804008 IRQ 42 MAC: 00:01:c0:02:45:9a NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron NAND 512MiB 3,3V 8-bit) Scanning device for bad blocks Bad eraseblock 299 at 0x0256 Bad eraseblock 2236 at 0x1178 Using static partition definition Creating 1 MTD partitions on "NAND 512MiB 3,3V 8-bit": 0x-0x2000 : "cmx270-0" usbmon: debugfs is not available pxa27x-ohci pxa27x-ohci: PXA27x OHCI pxa27x-ohci pxa27x-ohci: new USB bus registered, assigned bus number 1 pxa27x-ohci pxa27x-ohci: irq 3, io mem 0x4c00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 XScale iWMMXt coprocessor detected. eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 Sending DHCP requests ., OK IP-Config: Got DHCP answer from 0.0.0.0, my address is 192.168.10.76 IP-Config: Complete: device=eth0, addr=192.168.10.76, mask=255.255.255.0, gw=192.168.10.1, host=192.168.10.76, domain=spina.si, nis-domain=(none), bootserver=0.0.0.0, rootserver=192.168.10.124, rootpath= Looking up port of RPC 13/2 on 192.168.10.124 Looking up port of RPC 15/1 on 192.168.10.124 VFS: Mounted root (nfs filesystem). Freeing init memory: 108K Unable to handle kernel NULL pointer dereference at virtual address 0004 pgd = c0004000 [0004] *pgd= Internal error: Oops: f5 [#1] Modules linked in: CPU: 0Not tainted (2.6.22-cm-x270 #2) PC is at init_dev+0x38/0x5b8 LR is at tty_open+0xf8/0x33c pc : []lr : []psr: 6013 sp : c0423dec ip : c0423e38 fp : c0423e34 r10: r9 : r8 : 0002 r7 : 0001 r6 : c04e2200 r5 : c04e0d20 r4 : c02e5c3c r3 : r2 : c0423df0 r1 : c0423e08 r0 : c04e2200 Flags: nZCv IRQs on FIQs on Mode SVC_32 Segment kernel Control: 397f Table: a0004000 DAC: 0017 Process swapper (pid: 1, stack limit = 0xc0422260) Stack: (0xc0423dec to 0xc0424000) 3de0:c003ab44 c0423e3c c04e2200
Oops on arm pxa270 2.6.22
Hi I would like to ask what could be a problem or how could I start debuging it. My board is cm-x270 from compulab and it successfully boot until it should start init from busysbox. I get the folowing report. environment: pxa270 128Mb RAM network boot gcc 3.4.5 softfloat Linux image detected in memory at 0xA010, booting... Kernel parameters: root=/dev/nfs ip=:eth0: console=ttySA1,38400N1 bpp=16 nfsroot=192.168.10.124:/cm-x270 KERNEL_PARAMS: 0xA100 Linux version 2.6.22-cm-x270 ([EMAIL PROTECTED]) (gcc version 3.4.5) #2 Thu Jul 19 09:54:50 CEST 2007 CPU: XScale-PXA270 [69054117] revision 7 (ARMv5TE), cr=397f Machine: Compulab CM-x270 ATAG_INITRD is deprecated; please update your bootloader. Memory policy: ECC disabled, Data cache writeback Run Mode clock: 208.00MHz (*16) Turbo Mode clock: 520.00MHz (*2.5, active) Memory clock: 208.00MHz (/2) System bus clock: 208.00MHz CPU0: D VIVT undefined 5 cache CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets Built 1 zonelists. Total pages: 32512 Kernel command line: root=/dev/nfs ip=:eth0: console=ttySA1,38400N1 bpp=16 nfsroot=192.168.10.124:/cm-x270 PID hash table entries: 512 (order: 9, 2048 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 128MB = 128MB total Memory: 126848KB available (2492K code, 371K data, 108K init) SLUB: Genslabs=22, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Time: pxa_timer clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NetWinder Floating Point Emulator V0.97 (double precision) io scheduler noop registered io scheduler cfq registered (default) pxa2xx-fb pxa2xx-fb: Invalid resolution or bit depth pxa2xx-fb: probe of pxa2xx-fb failed with error -22 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled RAMDISK driver initialized: 4 RAM disks of 4096K size 1024 blocksize loop: module loaded dm9000 Ethernet Driver eth0: dm9000 at c8802000,c8804008 IRQ 42 MAC: 00:01:c0:02:45:9a NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron NAND 512MiB 3,3V 8-bit) Scanning device for bad blocks Bad eraseblock 299 at 0x0256 Bad eraseblock 2236 at 0x1178 Using static partition definition Creating 1 MTD partitions on "NAND 512MiB 3,3V 8-bit": 0x-0x2000 : "cmx270-0" usbmon: debugfs is not available pxa27x-ohci pxa27x-ohci: PXA27x OHCI pxa27x-ohci pxa27x-ohci: new USB bus registered, assigned bus number 1 pxa27x-ohci pxa27x-ohci: irq 3, io mem 0x4c00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 XScale iWMMXt coprocessor detected. eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 Sending DHCP requests ., OK IP-Config: Got DHCP answer from 0.0.0.0, my address is 192.168.10.76 IP-Config: Complete: device=eth0, addr=192.168.10.76, mask=255.255.255.0, gw=192.168.10.1, host=192.168.10.76, domain=spina.si, nis-domain=(none), bootserver=0.0.0.0, rootserver=192.168.10.124, rootpath= Looking up port of RPC 13/2 on 192.168.10.124 Looking up port of RPC 15/1 on 192.168.10.124 VFS: Mounted root (nfs filesystem). Freeing init memory: 108K Unable to handle kernel NULL pointer dereference at virtual address 0004 pgd = c0004000 [0004] *pgd= Internal error: Oops: f5 [#1] Modules linked in: CPU: 0Not tainted (2.6.22-cm-x270 #2) PC is at init_dev+0x38/0x5b8 LR is at tty_open+0xf8/0x33c pc : []lr : []psr: 6013 sp : c0423dec ip : c0423e38 fp : c0423e34 r10: r9 : r8 : 0002 r7 : 0001 r6 : c04e2200 r5 : c04e0d20 r4 : c02e5c3c r3 : r2 : c0423df0 r1 : c0423e08 r0 : c04e2200 Flags: nZCv IRQs on FIQs on Mode SVC_32 Segment kernel Control: 397f Table: a0004000 DAC: 0017 Process swapper (pid: 1, stack limit = 0xc0422260) Stack: (0xc0423dec to 0xc0424000) 3de0:c003ab44 c0423e3c c04e2200
Oops on arm pxa270 2.6.22
Hi I would like to ask what could be a problem or how could I start debuging it. My board is cm-x270 from compulab and it successfully boot until it should start init from busysbox. I get the folowing report. environment: pxa270 128Mb RAM network boot gcc 3.4.5 softfloat Linux image detected in memory at 0xA010, booting... Kernel parameters: root=/dev/nfs ip=:eth0: console=ttySA1,38400N1 bpp=16 nfsroot=192.168.10.124:/cm-x270 KERNEL_PARAMS: 0xA100 Linux version 2.6.22-cm-x270 ([EMAIL PROTECTED]) (gcc version 3.4.5) #2 Thu Jul 19 09:54:50 CEST 2007 CPU: XScale-PXA270 [69054117] revision 7 (ARMv5TE), cr=397f Machine: Compulab CM-x270 ATAG_INITRD is deprecated; please update your bootloader. Memory policy: ECC disabled, Data cache writeback Run Mode clock: 208.00MHz (*16) Turbo Mode clock: 520.00MHz (*2.5, active) Memory clock: 208.00MHz (/2) System bus clock: 208.00MHz CPU0: D VIVT undefined 5 cache CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets Built 1 zonelists. Total pages: 32512 Kernel command line: root=/dev/nfs ip=:eth0: console=ttySA1,38400N1 bpp=16 nfsroot=192.168.10.124:/cm-x270 PID hash table entries: 512 (order: 9, 2048 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 128MB = 128MB total Memory: 126848KB available (2492K code, 371K data, 108K init) SLUB: Genslabs=22, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Time: pxa_timer clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NetWinder Floating Point Emulator V0.97 (double precision) io scheduler noop registered io scheduler cfq registered (default) pxa2xx-fb pxa2xx-fb: Invalid resolution or bit depth pxa2xx-fb: probe of pxa2xx-fb failed with error -22 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled RAMDISK driver initialized: 4 RAM disks of 4096K size 1024 blocksize loop: module loaded dm9000 Ethernet Driver eth0: dm9000 at c8802000,c8804008 IRQ 42 MAC: 00:01:c0:02:45:9a NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron NAND 512MiB 3,3V 8-bit) Scanning device for bad blocks Bad eraseblock 299 at 0x0256 Bad eraseblock 2236 at 0x1178 Using static partition definition Creating 1 MTD partitions on NAND 512MiB 3,3V 8-bit: 0x-0x2000 : cmx270-0 usbmon: debugfs is not available pxa27x-ohci pxa27x-ohci: PXA27x OHCI pxa27x-ohci pxa27x-ohci: new USB bus registered, assigned bus number 1 pxa27x-ohci pxa27x-ohci: irq 3, io mem 0x4c00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 XScale iWMMXt coprocessor detected. eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 Sending DHCP requests ., OK IP-Config: Got DHCP answer from 0.0.0.0, my address is 192.168.10.76 IP-Config: Complete: device=eth0, addr=192.168.10.76, mask=255.255.255.0, gw=192.168.10.1, host=192.168.10.76, domain=spina.si, nis-domain=(none), bootserver=0.0.0.0, rootserver=192.168.10.124, rootpath= Looking up port of RPC 13/2 on 192.168.10.124 Looking up port of RPC 15/1 on 192.168.10.124 VFS: Mounted root (nfs filesystem). Freeing init memory: 108K Unable to handle kernel NULL pointer dereference at virtual address 0004 pgd = c0004000 [0004] *pgd= Internal error: Oops: f5 [#1] Modules linked in: CPU: 0Not tainted (2.6.22-cm-x270 #2) PC is at init_dev+0x38/0x5b8 LR is at tty_open+0xf8/0x33c pc : [c0135dd8]lr : [c0136450]psr: 6013 sp : c0423dec ip : c0423e38 fp : c0423e34 r10: r9 : r8 : 0002 r7 : 0001 r6 : c04e2200 r5 : c04e0d20 r4 : c02e5c3c r3 : r2 : c0423df0 r1 : c0423e08 r0 : c04e2200 Flags: nZCv IRQs on FIQs on Mode SVC_32 Segment kernel Control: 397f Table: a0004000 DAC: 0017 Process swapper (pid: 1, stack limit = 0xc0422260) Stack: (0xc0423dec to 0xc0424000) 3de0:c003ab44 c0423e3c
Oops on arm pxa270 2.6.22
Hi I would like to ask what could be a problem or how could I start debuging it. My board is cm-x270 from compulab and it successfully boot until it should start init from busysbox. I get the folowing report. environment: pxa270 128Mb RAM network boot gcc 3.4.5 softfloat Linux image detected in memory at 0xA010, booting... Kernel parameters: root=/dev/nfs ip=:eth0: console=ttySA1,38400N1 bpp=16 nfsroot=192.168.10.124:/cm-x270 KERNEL_PARAMS: 0xA100 Linux version 2.6.22-cm-x270 ([EMAIL PROTECTED]) (gcc version 3.4.5) #2 Thu Jul 19 09:54:50 CEST 2007 CPU: XScale-PXA270 [69054117] revision 7 (ARMv5TE), cr=397f Machine: Compulab CM-x270 ATAG_INITRD is deprecated; please update your bootloader. Memory policy: ECC disabled, Data cache writeback Run Mode clock: 208.00MHz (*16) Turbo Mode clock: 520.00MHz (*2.5, active) Memory clock: 208.00MHz (/2) System bus clock: 208.00MHz CPU0: D VIVT undefined 5 cache CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets Built 1 zonelists. Total pages: 32512 Kernel command line: root=/dev/nfs ip=:eth0: console=ttySA1,38400N1 bpp=16 nfsroot=192.168.10.124:/cm-x270 PID hash table entries: 512 (order: 9, 2048 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 128MB = 128MB total Memory: 126848KB available (2492K code, 371K data, 108K init) SLUB: Genslabs=22, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Time: pxa_timer clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NetWinder Floating Point Emulator V0.97 (double precision) io scheduler noop registered io scheduler cfq registered (default) pxa2xx-fb pxa2xx-fb: Invalid resolution or bit depth pxa2xx-fb: probe of pxa2xx-fb failed with error -22 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled RAMDISK driver initialized: 4 RAM disks of 4096K size 1024 blocksize loop: module loaded dm9000 Ethernet Driver eth0: dm9000 at c8802000,c8804008 IRQ 42 MAC: 00:01:c0:02:45:9a NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron NAND 512MiB 3,3V 8-bit) Scanning device for bad blocks Bad eraseblock 299 at 0x0256 Bad eraseblock 2236 at 0x1178 Using static partition definition Creating 1 MTD partitions on NAND 512MiB 3,3V 8-bit: 0x-0x2000 : cmx270-0 usbmon: debugfs is not available pxa27x-ohci pxa27x-ohci: PXA27x OHCI pxa27x-ohci pxa27x-ohci: new USB bus registered, assigned bus number 1 pxa27x-ohci pxa27x-ohci: irq 3, io mem 0x4c00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 XScale iWMMXt coprocessor detected. eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 Sending DHCP requests ., OK IP-Config: Got DHCP answer from 0.0.0.0, my address is 192.168.10.76 IP-Config: Complete: device=eth0, addr=192.168.10.76, mask=255.255.255.0, gw=192.168.10.1, host=192.168.10.76, domain=spina.si, nis-domain=(none), bootserver=0.0.0.0, rootserver=192.168.10.124, rootpath= Looking up port of RPC 13/2 on 192.168.10.124 Looking up port of RPC 15/1 on 192.168.10.124 VFS: Mounted root (nfs filesystem). Freeing init memory: 108K Unable to handle kernel NULL pointer dereference at virtual address 0004 pgd = c0004000 [0004] *pgd= Internal error: Oops: f5 [#1] Modules linked in: CPU: 0Not tainted (2.6.22-cm-x270 #2) PC is at init_dev+0x38/0x5b8 LR is at tty_open+0xf8/0x33c pc : [c0135dd8]lr : [c0136450]psr: 6013 sp : c0423dec ip : c0423e38 fp : c0423e34 r10: r9 : r8 : 0002 r7 : 0001 r6 : c04e2200 r5 : c04e0d20 r4 : c02e5c3c r3 : r2 : c0423df0 r1 : c0423e08 r0 : c04e2200 Flags: nZCv IRQs on FIQs on Mode SVC_32 Segment kernel Control: 397f Table: a0004000 DAC: 0017 Process swapper (pid: 1, stack limit = 0xc0422260) Stack: (0xc0423dec to 0xc0424000) 3de0:c003ab44 c0423e3c
Re: Oops on arm pxa270 2.6.22
Rok Markovic wrote: Hi I would like to ask what could be a problem or how could I start debuging it. My board is cm-x270 from compulab and it successfully boot until it should start init from busysbox. I get the folowing report. environment: pxa270 128Mb RAM network boot gcc 3.4.5 softfloat Linux image detected in memory at 0xA010, booting... [snip] pxa2xx-fb: probe of pxa2xx-fb failed with error -22 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled [snip] RAMDISK driver initialized: 4 RAM disks of 4096K size 1024 blocksize bootserver=0.0.0.0, rootserver=192.168.10.124, rootpath= Looking up port of RPC 13/2 on 192.168.10.124 Looking up port of RPC 15/1 on 192.168.10.124 VFS: Mounted root (nfs filesystem). Freeing init memory: 108K Unable to handle kernel NULL pointer dereference at virtual address 0004 pgd = c0004000 [0004] *pgd= Internal error: Oops: f5 [#1] Modules linked in: CPU: 0Not tainted (2.6.22-cm-x270 #2) PC is at init_dev+0x38/0x5b8 LR is at tty_open+0xf8/0x33c pc : [c0135dd8]lr : [c0136450]psr: 6013 [snip] 3fe0: c0423ff8 c003c9e8 c0008b30 e1a01007 ebfd4ec0 Backtrace: [c0135da0] (init_dev+0x0/0x5b8) from [c0136450] (tty_open+0xf8/0x33c) [c0136358] (tty_open+0x0/0x33c) from [c0088600] (chrdev_open+0x114/0x174) r8:c04e0d20 r7: r6: r5:c048f76c r4:c02e5c3c [c00884ec] (chrdev_open+0x0/0x174) from [c00847d0] (__dentry_open+0x188/0x228) r8:c0531c80 r7:c04ae364 r6:c00884ec r5:c048f76c r4:c04e0d20 [c0084648] (__dentry_open+0x0/0x228) from [c00848a4] (nameidata_to_filp+0x34/0x4c) [c0084870] (nameidata_to_filp+0x0/0x4c) from [c0084908] (do_filp_open+0x4c/0x50) r4:0002 [c00848bc] (do_filp_open+0x0/0x50) from [c0084c48] (do_sys_open+0x5c/0xec) r5: r4:0002 [c0084bec] (do_sys_open+0x0/0xec) from [c0084cfc] (sys_open+0x24/0x28) [c0084cd8] (sys_open+0x0/0x28) from [c0023300] (init_post+0x2c/0xfc) [c00232d4] (init_post+0x0/0xfc) from [c0008c80] (kernel_init+0x15c/0x2bc) r4:c02afed8 [c0008b24] (kernel_init+0x0/0x2bc) from [c003c9e8] (do_exit+0x0/0x86c) Code: e3a03000 e5823000 059030b8 e1a06000 (07935107) Kernel panic - not syncing: Attempted to kill init! I think you have conflict between PXA serial and 8250 drivers. Make sure you use only one of them. If you need to use PCMCIA serial cards, please see http://lists.arm.linux.org.uk/pipermail/linux-arm-kernel/2007-July/040604.html -- Sincerely yours, Mike. - To unsubscribe from this list: send the line unsubscribe linux-kernel in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/
Re: Oops on arm pxa270 2.6.22
Mike Rapoport wrote: I think you have conflict between PXA serial and 8250 drivers. Make sure you use only one of them. If you need to use PCMCIA serial cards, please see http://lists.arm.linux.org.uk/pipermail/linux-arm-kernel/2007-July/040604.html Thanks, I already fixed my problem. You are right it was serial port problem. I had wrong MAJOR and MINOR numbers in serial/pxa.c Now kerel boots and works fine with -ck patch. My I ask you if you (compulab) have any plans of merging machine cm-x270 patches into mainline kernel. Thanks again, Rok Markovic - To unsubscribe from this list: send the line unsubscribe linux-kernel in the body of a message to [EMAIL PROTECTED] More majordomo info at http://vger.kernel.org/majordomo-info.html Please read the FAQ at http://www.tux.org/lkml/