On Sun, Jun 3, 2012 at 6:42 PM, John Swink wrote:
> Maybe the best antenna solution is a very large discone antenna like the
> one
> at the old missile site near Tucson, AZ. Unity gain but very large
> bandwidth.
>
A very-common, no-tune RX antenna is the Tilted Terminated Folded Dipole
(T2FD).
or, something as simple as an active vertical...e.g. a hi-Z plus 6 with 10 to
20' vertical against a single short ground rod...several other small active
antennas have very wide bandwidth also..73, w5xz, dan
--- On Mon, 6/4/12, John Swink wrote:
From: John Swink
Subject: Re: [Flexradio] Flex-
Maybe the best antenna solution is a very large discone antenna like the one
at the old missile site near Tucson, AZ. Unity gain but very large
bandwidth.
John, N8WNA
-Original Message-
From: flexradio-boun...@flex-radio.biz
[mailto:flexradio-boun...@flex-radio.biz] On Behalf Of Mike Va
I have an M2 7&10-30LP8 log periodic up at 120 feet that will do wonders as an
input to the Flex-6xxx receivers.
http://www.m2inc.com/pdf_manuals/7%20&%2010-30LP8.pdf
It covers 40M-10M very well and makes an interesting "monitor" antenna on 6
meters with lots of minor lobes shooting off very wh
I'd like to hear from users that have the V/U module installed that are
using it in the satellites. Is it necessary to have the 2nd rcvr installed
to operate full duplex? What tracking software are you using and have you
found any glitches. I'm trying to decide on the upgrade and whether to fund
it
Think log periodics...several good ones out there that cover 14 - 30 MHz,
giving 5 bands and some do 10 - 30 MHz. Stack 'em and they are very
competitive.
Chuck K1KW - check out my QRZ.com picture for such an antenna.
- Original Message -
From: "Jim Jannuzzo"
To: ; "Gerald Youngblo
It would seem to me that the SteppIR will only track the TX freq, which there
will only be one freq. The other slices will get what the Rx antenna will
cover, and slices out of the antenna gain range will be down.. The slice that
is tracking the Tx will be fine..
Is that too simple of an explan
Jack,This very question has been troubling me. SInce the radio will receive
all frequencies, and display 8 slices of them, how do you engineer an antenna
with gain across all frequencies, and/or gain in eight directions? (Since the
6700 has two antenna paths for its eight slices, you'd really
Mathias,The standard method to troubleshoot. when all else fails: Reset the
database to factory defaults. If that fixes the problem, then an option was
inadvertantly set incorrectly, or a PC crash hurt the file. If the radio works
again, then you can import the tables with Ray K9DUR SDRDataTra
Well I've been on the air here (PJ4 land) for about 24 hours and I continue
to have some lock-up problems (every 15 minutes or so). I even shut down
N1MM (just using the logging part). I think the problem now is I can't get
a good ground anywhere. The CPU is running about 10% loaded.
Dr.
A diagram of the hardware innards will certainly be helpful.But I think
some diagrams showing how the new hardware might be used within an overall
station would be even better.
For example, the ability to receive (and presumably transmit where legal)
over the DC-to-daylight spectrum is techni
Hello,
i never used the squelch before, but if it is swiched on squelch is
working. I have it off normaly. It is not the problem.
Thanks for the hint. But i have to look for another reason.
Regards
Mathias
HB9DOU
2012/6/3 Rich - W3ZJ :
> Did you click the "SQL: - ..." button just above the slide
On Sat, May 26, 2012 at 9:53 AM, Brian Lloyd wrote:
> On Sat, May 26, 2012 at 9:02 AM, Gerald Youngblood >wrote:
>
>
>
So the solution is to do one of two things:
>
> 1. Keep adding all kinds of switching to the radio itself, e.g. more
> processing loops;
> 2. move all the switching
was there a sn# on the 3000's that would show the rig had the preamp upgrade
from the factory? If a older 3000 went back to flex to be upgraded, anyone have
a guess on the cost and was the upgrade worthit?
thanks
dale wt4t
___
FlexRadio Systems Mai
There should only be two command lines.
To fix the word-wrap in the original post:
The first command starts with "rename" and there is a space between
"Default" and "2012"
The second command starts with "copy" and there is a space between "Default"
and "2012" and between "FlexRadio" and "Systems".
Elan
You can move the Flex Radio logo from the top-right corner of the display to
the bottom-right corner by opening a command window and entering these two
commands:
rename "%appdata%\FlexRadio Systems\PowerSDR\Skins\Default
2012\Console\picDisplay.png" "WAS_picDisplay.png"
copy "%appdata%\FlexR
You can edit the background skins in mspaint. I don't recall where they were,
but it didn't take long to find them and the edits only took a couple minutes.
Jim
Sent from my iPad
On Jun 3, 2012, at 4:09 AM, paim wrote:
>
> I may ask very kind on the next release of PSDR to remove from the
I may ask very kind on the next release of PSDR to remove from the skin flex
radio logo it is on the scope and it is better to add it on some where else
thank you
vy 73
E.P g0uut/dl9fcc
___
FlexRadio Systems Mailing List
FlexRadio@flex-radio.biz
18 matches
Mail list logo