Various calls that downgrade permissions or virtually copy a pmap in
pmap.c now remove PG_W (and did not 6 months ago). This may be the
cause of the regression. It would probably be better (and faster) if
the pages were "held" instead of wired.
-Kip
On Nov 13, 2007 4:49 PM, Kris Kennaway <[EM
Kip Macy wrote:
Unfortunately, ZERO_COPY_SOCKETs have long been a known source of
problems. I think also, when a page is copied as part of COW the new
page is unwired (see pmap_copy et al.), this could lead to
socow_iodone unwiring after send a page that was not wired. An added
issue is that part
On Nov 13, 2007, at 5:13 PM, Kip Macy wrote:
In the meantime, your best bet is to disable ZERO_COPY_SOCKETS.
Thanks for the info. I'm putting the new kernel in place and will see
what happens and report back.
___
freebsd-stable@freebsd.org mail
Unfortunately, ZERO_COPY_SOCKETs have long been a known source of
problems. I think also, when a page is copied as part of COW the new
page is unwired (see pmap_copy et al.), this could lead to
socow_iodone unwiring after send a page that was not wired. An added
issue is that parts of the VM assume
On 11/13/07, Vivek Khera <[EMAIL PROTECTED]> wrote:
>
> On Nov 13, 2007, at 4:50 PM, Vlad GALU wrote:
>
> >>vmio = 1
> >>offset = Unhandled dwarf expression opcode 0x93
> >> (kgdb)
> >>
> >
> >Do you happen to have ZERO_COPY_SOCKETS in your kernel config?
> >
> >
>
> Yes, I do.
On Nov 13, 2007, at 4:50 PM, Vlad GALU wrote:
vmio = 1
offset = Unhandled dwarf expression opcode 0x93
(kgdb)
Do you happen to have ZERO_COPY_SOCKETS in your kernel config?
Yes, I do. Are they known to be bad under certain loads or just in
general. I don't have this
On 11/13/07, Vivek Khera <[EMAIL PROTECTED]> wrote:
> I've got a Dell 1750 box that was rock-solid stable running 4.11 for a
> couple of years now operating a pretty busy website backend. A month
> or so ago we wiped it clean and repurposed it to run a different
> website running Drupal with a Var
I've got a Dell 1750 box that was rock-solid stable running 4.11 for a
couple of years now operating a pretty busy website backend. A month
or so ago we wiped it clean and repurposed it to run a different
website running Drupal with a Varnish front-end cache using FreeBSD
6.2-RELEASE-p5.
On Tue, Nov 13, 2007 at 07:18:19AM -0500, Aryeh M. Friedman wrote:
> Just for the record what chipset is your Mobo (it has been reported on
> several but most commonly ICH9(R)? Also don't expect any more
The board has an AMD 8151+8111 combo with a SiI 3114 SATA Controller,
so it's not an Inte
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
Uwe Laverenz wrote:
> On Tue, Nov 13, 2007 at 07:04:34AM -0500, Aryeh M. Friedman wrote:
>
>>> and constantly gets read timeouts == no installation possible.
>> Yes and it is under active investigation.
>
> Thank you. :)
Just for the record what chips
On Tue, 13 Nov 2007 09:38:00 +0100 Gerrit Kühn
<[EMAIL PROTECTED]> wrote about System unbootable after upgrade
to FBSD 7:
GK> Can't work out which disk we are booting from.
GK> Guessed BIOS device 0x not found by probes, defaulting to
GK> disk0:
GK> panic: free: guard1 fail @ 0x6c23c
GK> f
On Tue, Nov 13, 2007 at 07:04:34AM -0500, Aryeh M. Friedman wrote:
> > and constantly gets read timeouts == no installation possible.
>
> Yes and it is under active investigation.
Thank you. :)
Uwe
___
freebsd-stable@freebsd.org mailing list
http://l
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
Uwe Laverenz wrote:
> Hi,
>
> I was trying to install 7.0 beta 2 on a system that has a SATA attached
> DVD drive. The system starts to the point where it waits for the SCSI
> devices to initialize. After that it starts reading from the install media
>
I upgraded an old machine from 6.2-RELEASE-p7 to 6.3-BETA1 (via
freebsd-update).
Now every ten seconds I get:
acpi_tz0: _TMP value is absurd, ignored (-13.4C)
At the same time, I have:
hw.acpi.thermal.tz0.temperature: -273.2C
The machine has a Gigabyte GA-686BX board with Intel 82440 BX chip
Hi,
I just upgraded my first system from 6-stable to 7. installkernel and
installworld went well. However, the system won't boot anymore. :-(
The bootloader still appears, grabs kernel and modules, followed by
Can't work out which disk we are booting from.
Guessed BIOS device 0x not found
15 matches
Mail list logo
