console_buffer array is defined to be CONFIG_SYS_CBSIZE + 1 long,
whereas the_command array only CONFIG_SYS_CBSIZE long. Subsequent
use of strcpy(the_command, console_buffer) will write final \0
terminating byte outside the_command array when entering a command
of max length.
Signed-off-by: Kristi
Hi,
I would like to request your participation in a survey on
Open Source Organizational Culture,
which will provide valuable insight into how Open Source projects are
run, how their participants act, how they might change going forward,
and how particular Open Source projects compare with
According to AN3638, CRC of NXID v1 is at the end of the
256-byte I2C memory. The wrong CRC32 offset prevents Uboot
from reading system information from EEPROM. No NXID v0 is
being used on Freescale boards.
Signed-off-by: Ebony Zhu
---
board/freescale/common/sys_eeprom.c | 7 ---
1 file chan
Hello York,
Am 25.04.2014 21:06, schrieb York Sun:
U-boot image has grown and exceeded the predefined 512KB. Increasing to
768KB to align with other powerpc boards. Tested on MPC8572DS for 32-
and 36-bit targets with NOR flash boot. NAND boot is not covered by
this patch.
Also update board main
This patch converts MC8536DS to use generic board. This is for discussion.
Do NOT apply.
To make it work
Add #ifdef CONFIG_OF_CONTROL for reserve_fdt(), setup_fdt(), reloc_fdt().
Set initial value for gd. Powerpc SoCs use locked cache as init RAM.
Change return value for mac_read_from_eeprom() wh
Signed-off-by: Eric Nelson
---
Note that this seems a bit premature until we have some infrastructure
around DTB files in place, but we certainly don't want big hairy
warning messages on our boards.
Is anyone planning on pulling in at least the pinfunc and .dtsi
files for i.MX? I'm not sure how
Signed-off-by: Tim Harvey
---
board/gateworks/gw_ventana/gw_ventana.c | 134
include/configs/gw_ventana.h| 16
2 files changed, 150 insertions(+)
diff --git a/board/gateworks/gw_ventana/gw_ventana.c
b/board/gateworks/gw_ventana/gw_ventana.c
ind
On 03/22/2014 04:14 PM, Simon Glass wrote:
> We should move forward to remove the old board init code. Add a
> prominent message to encourage maintainers to get started on this
> work.
>
> Signed-off-by: Simon Glass
> ---
>
Simon,
How much test has been done on powerpc boards? I randomly pick on
Enable CONFIG_SYS_GENERIC_BOARD on ventana.
Signed-off-by: Tim Harvey
---
include/configs/gw_ventana.h | 2 ++
1 file changed, 2 insertions(+)
diff --git a/include/configs/gw_ventana.h b/include/configs/gw_ventana.h
index b984f27..335f2ff 100644
--- a/include/configs/gw_ventana.h
+++ b/include/
On Thu, Apr 24, 2014 at 01:20:56PM +0200, Stefan Roese wrote:
> Hi Tom,
>
> please pull the following patch:
>
> The following changes since commit adcdeacc3eda1e5949e54062aa99c299e12483be:
>
> Merge branch 'master' of git://git.denx.de/u-boot-mips (2014-04-23 11:07:11
> -0400)
>
> are avai
On Fri, Apr 25, 2014 at 02:24:57PM +, Alexey Brodkin wrote:
> Dear Tom,
>
> The following changes since commit
> adcdeacc3eda1e5949e54062aa99c299e12483be:
>
> Merge branch 'master' of git://git.denx.de/u-boot-mips (2014-04-23
> 11:07:11 -0400)
>
> are available in the git repository at:
>
On Wed, Apr 23, 2014 at 07:13:27PM -0500, Kim Phillips wrote:
> Hi Tom,
>
> Please pull support for the ids8313 board:
>
> The following changes since commit adcdeacc3eda1e5949e54062aa99c299e12483be:
>
> Merge branch 'master' of git://git.denx.de/u-boot-mips (2014-04-23 11:07:11
> -0400)
>
On Wed, Apr 23, 2014 at 03:45:05PM -0700, York Sun wrote:
> Tom,
>
> The following changes since commit b149c4c399b111cec1ff7505ca9fabbeeb4fe394:
>
> ARM:tegra20: Remove aes debug prints (2014-04-18 16:14:17 -0400)
>
> are available in the git repository at:
>
> git://git.denx.de/u-boot-mp
Hi Jeff,
2014-04-25 18:18 GMT+02:00 Jeff Horn :
> Hi,
>
> I am new to u-boot. I have u-boot working on a custom board for the
> freescale i.MX6 Solo. We have SPI NOR (m25p32) and with sf probe I can see
> the device. I can also erase/write/read and boot my kernel from SPI NOR.
> However, I just ca
U-boot image has grown and exceeded the predefined 512KB. Increasing to
768KB to align with other powerpc boards. Tested on MPC8572DS for 32-
and 36-bit targets with NOR flash boot. NAND boot is not covered by
this patch.
Also update board maintainer for these boards.
Signed-off-by: York Sun
---
On Wed, Apr 16, 2014 at 03:44:36PM +0900, Masahiro Yamada wrote:
> arch/arm/include/asm/spl.h requires all SoCs to have
> arch/arm/include/asm/arch-*/spl.h.
>
> But many of them just define BOOT_DEVICE_* macros.
>
> Those macros are used in the "switch (boot_device) { ... }"
> statement in commo
Hi,
I am new to u-boot. I have u-boot working on a custom board for the
freescale i.MX6 Solo. We have SPI NOR (m25p32) and with sf probe I can see
the device. I can also erase/write/read and boot my kernel from SPI NOR.
However, I just can not figure out how to use MTD's. I have MTDIDS_DEFAULT
"n
Hi all -
I noticed that in zynq_sdhci.c, responsible for initializing PS SD
controller(s), host controller max clock frequency is always set to 52MHz
(http://git.denx.de/?p=u-boot.git;a=blob;f=drivers/mmc/zynq_sdhci.c;h=fdce2c2c10ec85c4a291532f927eae4a0b5627c9;hb=master#l34).
In cases where use
Fix typo in setting of system-serial property causing the prop len to be
off by 1.
Signed-off-by: Tim Harvey
---
board/gateworks/gw_ventana/gw_ventana.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/board/gateworks/gw_ventana/gw_ventana.c
b/board/gateworks/gw_ventana/gw_ve
Hi Przemyslaw Marczak,
>Hi,
>
>On 04/21/2014 04:25 PM, Akshay Saraswat wrote:
>> This patch includes following changes :
>> * Adds gpio pin numbering support for EXYNOS SOCs.
>>To have consistent 0..n-1 GPIO numbering the banks are divided
>>into different parts where ever they have holes
Hi Przemyslaw Marczak,
>Hello,
>
>On 04/21/2014 04:25 PM, Akshay Saraswat wrote:
>> Used a script to recheck/verify pin mapping and existing mapping
>> appears to be fine, returning correct bank and pin values.
>> Did ./MAKEALL -a arm and found all Exynos/S5P related boards
>> compiled successfull
Dear Tom,
The following changes since commit
adcdeacc3eda1e5949e54062aa99c299e12483be:
Merge branch 'master' of git://git.denx.de/u-boot-mips (2014-04-23
11:07:11 -0400)
are available in the git repository at:
ssh://gu-...@git.denx.de/u-boot-arc master
for you to fetch changes up to 0cdd7
On 22/04/2014 20:34, Fabio Estevam wrote:
> Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning
> on
> boot:
>
> "Warning: Your board does not use generic board. Please read
>
> doc/README.generic-board and take action. Boards not
Add missing header.
Warnings:
drivers/net/zynq_gem.c:491:5: warning: symbol 'zynq_gem_initialize' was not
declared. Should it be static?
drivers/net/zynq_gem.c:542:5: warning: symbol 'zynq_gem_of_init' was not
declared. Should it be static?
Signed-off-by: Michal Simek
---
drivers/net/zynq_ge
From: "Jesper B. Christensen"
Signed-off-by: Jesper B. Christensen
Signed-off-by: Michal Simek
---
drivers/i2c/zynq_i2c.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/i2c/zynq_i2c.c b/drivers/i2c/zynq_i2c.c
index f1f6513..b3264af 100644
--- a/drivers/i2c/zyn
Warnings:
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_init' was not
declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_setbrg' was not
declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_get
's/zynq_serial_initalize/zynq_serial_initialize/g'
serial_initialize is used by all serial drivers.
Signed-off-by: Michal Simek
---
drivers/serial/serial.c | 4 ++--
drivers/serial/serial_zynq.c | 2 +-
2 files changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/serial/serial.c
From: Siva Durga Prasad Paladugu
Assign default environment and set env valid during board_init_f
before relocation as the actual environment will be read from
eeprom later.
Signed-off-by: Siva Durga Prasad Paladugu
Signed-off-by: Michal Simek
---
common/env_eeprom.c | 5 +
1 file change
From: Siva Durga Prasad Paladugu
Define MAX_CLUSTSIZE only if not defined in board specific
config file as this size can be decreased to save memory
in some memory constrained cases.
Signed-off-by: Siva Durga Prasad Paladugu
Signed-off-by: Michal Simek
---
include/fat.h | 2 ++
1 file change
From: Siva Durga Prasad Paladugu
Added support for Spansion chip "S25FL512S_512K".
Signed-off-by: Siva Durga Prasad Paladugu
Signed-off-by: Michal Simek
---
drivers/mtd/spi/sf_params.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/mtd/spi/sf_params.c b/drivers/mtd/spi/sf_params
Hello,
On 04/21/2014 04:25 PM, Akshay Saraswat wrote:
Used a script to recheck/verify pin mapping and existing mapping
appears to be fine, returning correct bank and pin values.
Did ./MAKEALL -a arm and found all Exynos/S5P related boards
compiled successfully.
Couldn't test booting over all of
Hi,
On 04/21/2014 04:25 PM, Akshay Saraswat wrote:
This patch includes following changes :
* Adds gpio pin numbering support for EXYNOS SOCs.
To have consistent 0..n-1 GPIO numbering the banks are divided
into different parts where ever they have holes in them.
* Rename GPIO definitions f
15 was too small for variables stored in file on MMC.
Signed-off-by: Michal Simek
---
include/configs/zynq-common.h | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/include/configs/zynq-common.h b/include/configs/zynq-common.h
index 09d6c55..d2149b3 100644
--- a/include/confi
MII is used by this driver.
Signed-off-by: Michal Simek
---
drivers/net/zynq_gem.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/net/zynq_gem.c b/drivers/net/zynq_gem.c
index 101489c..08056a4 100644
--- a/drivers/net/zynq_gem.c
+++ b/drivers/net/zynq_gem.c
@@ -33
From: Siva Durga Prasad Paladugu
Added configs to support USB host for zynq boards.
Also added a command usbboot to boot from usb.
Signed-off-by: Siva Durga Prasad Paladugu
Signed-off-by: Michal Simek
---
include/configs/zynq-common.h | 20 +++-
include/configs/zynq_zc70x.h
From: Michal Simek
Add run-time MIO pin detection to get actual
pin configuration for specific periphery.
Signed-off-by: Michal Simek
---
arch/arm/cpu/armv7/zynq/slcr.c | 50 ++
arch/arm/include/asm/arch-zynq/sys_proto.h | 1 +
2 files changed, 51 inse
From: Siva Durga Prasad Paladugu
Enabled the EXT4 configs.
Signed-off-by: Siva Durga Prasad Paladugu
Signed-off-by: Michal Simek
---
include/configs/zynq-common.h | 2 ++
1 file changed, 2 insertions(+)
diff --git a/include/configs/zynq-common.h b/include/configs/zynq-common.h
index 0a7d104
From: Michal Simek
Added USB host driver for zynq.
Signed-off-by: Siva Durga Prasad Paladugu
Signed-off-by: Michal Simek
---
arch/arm/cpu/armv7/zynq/slcr.c| 24 +++
arch/arm/include/asm/arch-zynq/hardware.h | 2 +
drivers/usb/host/Makefile | 1 +
drivers/
From: Siva Durga Prasad Paladugu
Moved the USB/SD/MMC common FAT configs separately
to avoid redefinition warnings.
Signed-off-by: Siva Durga Prasad Paladugu
Signed-off-by: Michal Simek
---
include/configs/zynq-common.h | 14 --
1 file changed, 8 insertions(+), 6 deletions(-)
di
From: Siva Durga Prasad Paladugu
Enable the FAT write capability for SD/MMC write
functionality.
Signed-off-by: Siva Durga Prasad Paladugu
Signed-off-by: Michal Simek
---
include/configs/zynq-common.h | 1 +
1 file changed, 1 insertion(+)
diff --git a/include/configs/zynq-common.h b/include
Extend max kernel image size. Gunzip is checking
this value. If kernel is larger, message below is shown.
Uncompressing Kernel Image ... Error: inflate() returned -5
GUNZIP: uncompress, out-of-mem or overwrite error -
must RESET board to recover
Signed-off-by: Michal Simek
---
include/configs/
When CONFIG_FPGA is defined but CONFIG_SPL_FPGA is not, the build fails:
board.c: In function 'board_init':
board.c:41:3: error: 'fpga' undeclared (first use in this function)
fpga = fpga010;
Fix this by expanding the "#if.." around this block to match the other
FPGA checks and don't compile th
The driver should setup slcr state according
to slcr operations.
Reported-by: Andrey Filippov
Signed-off-by: Michal Simek
---
arch/arm/cpu/armv7/zynq/slcr.c | 8 ++--
1 file changed, 6 insertions(+), 2 deletions(-)
diff --git a/arch/arm/cpu/armv7/zynq/slcr.c b/arch/arm/cpu/armv7/zynq/slcr
Fix c&p error in zynq_slcr_devcfg_enable() commentary
and extending it with description according
to Zynq TRM also in zynq_slcr_devcfg_disable().
Signed-off-by: Michal Simek
---
arch/arm/cpu/armv7/zynq/slcr.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/cpu/a
From: Mike Looijmans
Bootmode mask was defined as 0x0F, but documentation mentions 0x07.
Experiments show that bit "3" is the JTAG chain configuration.
Change the mask to "7" to allow systems with a different chain
configuration to boot correctly.
Signed-off-by: Mike Looijmans
Signed-off-by: Mi
From: Michal Simek
Call board_init() if SPL is configured with CONFIG_SPL_BOARD_INIT.
Signed-off-by: Michal Simek
Signed-off-by: Michal Simek
---
arch/arm/cpu/armv7/zynq/spl.c | 7 +++
include/configs/zynq-common.h | 1 +
2 files changed, 8 insertions(+)
diff --git a/arch/arm/cpu/armv7/
Memory size should be specified without ECC place.
If you need to have half memory size, please change
u-boot configuration.
Signed-off-by: Michal Simek
---
arch/arm/cpu/armv7/zynq/ddrc.c | 3 ---
1 file changed, 3 deletions(-)
diff --git a/arch/arm/cpu/armv7/zynq/ddrc.c b/arch/arm/cpu/armv7/z
Warnings:
board/xilinx/zynq/board.c:17:13: warning: symbol 'fpga' was not declared.
Should it be static?
board/xilinx/zynq/board.c:20:13: warning: symbol 'fpga010' was not declared.
Should it be static?
board/xilinx/zynq/board.c:21:13: warning: symbol 'fpga015' was not declared.
Should it be sta
From: Siva Durga Prasad Paladugu
Added efuse status register base address. This register
is used for determining whether efuse was blown or not.
Also, added the zynq_get_silicon_version() to get the
silicon version of the zynq board.
Signed-off-by: Siva Durga Prasad Paladugu
Signed-off-by: Mich
Warning:
arch/arm/cpu/armv7/zynq/ddrc.c:43:24: warning: Using plain integer as NULL
pointer
Signed-off-by: Michal Simek
---
arch/arm/cpu/armv7/zynq/ddrc.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm/cpu/armv7/zynq/ddrc.c b/arch/arm/cpu/armv7/zynq/ddrc.c
index b
Warnings:
arch/arm/cpu/armv7/zynq/slcr.c:21:6: warning: symbol 'zynq_slcr_lock' was not
declared. Should it be static?
arch/arm/cpu/armv7/zynq/slcr.c:27:6: warning: symbol 'zynq_slcr_unlock' was not
declared. Should it be static?
arch/arm/cpu/armv7/zynq/slcr.c:34:6: warning: symbol 'zynq_slcr_cpu
Hi,
I am sending ARM zynq changes.
This series is based on FPGA changes I have sent
http://lists.denx.de/pipermail/u-boot/2014-April/178204.html
(There is small dependency on some patches).
My expectation is that fpga series will go to Tom's tree
first.
Thanks,
Michal
Michal Simek (12):
ARM:
From: Siva Durga Prasad Paladugu
Use zynq_dma_xfer_init, zynq_align_dma_buffer,
zynq_dma_transfer helper function performing dma
transfers so that the code can be reused easily for
different cases of dma transfer.
Signed-off-by: Siva Durga Prasad Paladugu
Signed-off-by: Michal Simek
---
driv
No functional changes.
Signed-off-by: Michal Simek
---
board/armadeus/apf27/fpga.c | 2 +-
board/astro/mcf5373l/fpga.c | 2 +-
board/balloon3/balloon3.c| 2 +-
board/esd/pmc440/fpga.c | 2 +-
board/gen860t/fpga.c | 2 +-
board/matr
On Fri, Apr 25, 2014 at 12:26 AM, Lukasz Majewski
wrote:
> Hi Rob,
>
>> On Wed, Apr 23, 2014 at 6:02 AM, Lukasz Majewski
>> wrote:
>> > Hi Rob,
>> >
>> >> From: Sebastian Siewior
>> >>
>> >> This patch contains an implementation of the fastboot protocol on
>> >> the device side and documentation
From: Siva Durga Prasad Paladugu
Use helper function zynq_validate_bitstream so that the
code can be reused easily for different cases of dma transfer.
Signed-off-by: Siva Durga Prasad Paladugu
Signed-off-by: Michal Simek
---
For first 6 patches RFC were sent
---
drivers/fpga/zynqpl.c | 32 +
Warnings:
drivers/fpga/zynqpl.c:150:32: warning: Using plain integer as NULL pointer
drivers/fpga/zynqpl.c:152:16: warning: Using plain integer as NULL pointer
Signed-off-by: Michal Simek
---
drivers/fpga/zynqpl.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/f
No functional changes.
Signed-off-by: Michal Simek
---
include/spartan2.h | 40
include/spartan3.h | 44 ++--
include/virtex2.h | 34 +-
include/xilinx.h | 42
Connect FPGA version with appropriate operations
to remove huge switch-cases for every FPGA family.
Tested on Zynq. Spartan2/Spartan3/Virtex2 just compile test.
Signed-off-by: Michal Simek
---
Based on http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/182419
I have checked that symbols a
No functional changes.
Signed-off-by: Michal Simek
---
board/gen860t/fpga.c | 4 ++--
drivers/fpga/virtex2.c | 34 +-
drivers/fpga/xilinx.c | 14 +++---
include/virtex2.h | 34 +-
include/xilinx.h | 2 +-
5
No functional changes.
Signed-off-by: Michal Simek
---
board/armadeus/apf27/fpga.c | 4 ++--
board/astro/mcf5373l/fpga.c | 4 ++--
board/balloon3/balloon3.c| 2 +-
board/esd/pmc440/fpga.c | 4 ++--
board/matrix_vision/mvsmr/fpga.c | 2 +-
boar
No functional changes.
Signed-off-by: Michal Simek
---
board/esd/pmc440/fpga.c | 2 +-
board/matrix_vision/mvsmr/fpga.c | 2 +-
drivers/fpga/spartan2.c | 40
drivers/fpga/xilinx.c| 14 +++---
include/spartan2.h
Commit 33a02da0 supported "" for the board field of boards.cfg.
But it missed to modify spl/Makefile.
This commit provides the flexibility so we can use "" board
in SPL too.
---
spl/Makefile | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/spl/Makefile b/spl/Makefile
index 6fec
The build fails if a non-generic ARM board is compiled
with CONFIG_OF_EMBED=y.
The correct symbol name for embedded FDT is not __dtb_db_begin,
but __dtb_dt_begin. (A typo introduced by commit 6ab6b2af)
Signed-off-by: Masahiro Yamada
---
arch/arm/lib/board.c | 2 +-
1 file changed, 1 insertion(+
This menu option allows restore gpt.
This is usefull and no needs access to the u-boot console.
For proper operation:
- each partition uuid should be set in environment or
- CONFIG_RANDOM_UUID should be defined for automatically uuid setting
After operation success device is going to be reset.
Si
This change prevents gpio keys bouncing by adding 50 ms delay
when key pressed condition met.
Signed-off-by: Przemyslaw Marczak
Cc: Minkyu Kang
---
Changes v2:
- new commit
Changes v3:
- correct commit message
Changes v4:
- none
board/samsung/common/misc.c | 4
1 file changed, 4 inserti
This change removes LCD menu download mode info screen.
Now key press timeout is checked in function download_menu()
and menu options are displayed directly after PWR + VOLUP keys.
Signed-off-by: Przemyslaw Marczak
---
Changes v4:
- new commit
board/samsung/common/misc.c | 73 ++
Function cmd_process() runs commands with directly given list of arguments
but it doesn't expand given environmental variables names as macros.
Command "gpt" as one of arguments expects expanded macro e.g. $partitions
so it needs to be called by function run_command().
Changes:
- extend array mode
From: Inha Song
This change allows reset device environment to default without using u-boot
console, which is useful for system developers.
Signed-off-by: Inha Song
Acked-by: Przemyslaw Marczak
Cc: Minkyu Kang
---
Changes v2:
- extend commit message
Changes v3:
- none
Changes v4:
- none
b
>From: Marek Belisko [mailto:marek.beli...@gmail.com]
>
>We need to flip only one bit not assign.
>
>Signed-off-by: Marek Belisko
>---
> drivers/mtd/nand/omap_gpmc.c |2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
>diff --git a/drivers/mtd/nand/omap_gpmc.c b/drivers/mtd/nand/omap_gpmc.
We need to flip only one bit not assign.
Signed-off-by: Marek Belisko
---
drivers/mtd/nand/omap_gpmc.c |2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/mtd/nand/omap_gpmc.c b/drivers/mtd/nand/omap_gpmc.c
index 881a636..bf99b8e 100644
--- a/drivers/mtd/nand/omap_gpmc
when qe-ucode fails to be uploaded, disable qe.
Signed-off-by: Zhao Qiang
---
drivers/qe/qe.c | 4
1 file changed, 4 insertions(+)
diff --git a/drivers/qe/qe.c b/drivers/qe/qe.c
index b1da75e..c77cc16 100644
--- a/drivers/qe/qe.c
+++ b/drivers/qe/qe.c
@@ -14,6 +14,8 @@
#include "asm/immap
The T4080 SoC is a low-power version of the T4160.
T4080 combines 4 dual-threaded Power Architecture e6500
cores with single cluster and two memory complexes.
Signed-off-by: Shengzhou Liu
---
v2: add more comments.
arch/powerpc/cpu/mpc85xx/Makefile | 2 ++
arch/powerpc/cpu/mpc85xx/cpu.
Hi Ian,
On Thu, 2014-04-24 at 20:14 +0100, Ian Campbell wrote:
> On Thu, 2014-04-24 at 17:41 +, Alexey Brodkin wrote:
>
> > 1. Don't invalidate "sizeof(struct dmamacdescr)" but only
> > "roundup(sizeof(desc_p->txrx_status), ARCH_DMA_MINALIGN))".
>
> OK. (Although given the realities of the r
Hi Marek,
>From: Belisko Marek [mailto:marek.beli...@gmail.com]
[...]
>With original patch (or with your) it fix only u-boot but it doesn't
>fix loading u-boot from SPL as it using custom nand_read_page (in
>am335x_spl_bch.c)
>and not from nand_bases there must be other update to fix this issue.
>
Hi Pekon,
On Thu, Apr 24, 2014 at 1:53 PM, Gupta, Pekon wrote:
> Hi Marek,
>
>>From: Belisko Marek [mailto:marek.beli...@gmail.com]
>>On Wed, Apr 23, 2014 at 8:04 PM, Gupta, Pekon wrote:
From: Belisko Marek [mailto:marek.beli...@gmail.com]
CC-ing Pekon Gupta which add those changes
> From: u-boot-boun...@lists.denx.de [mailto:u-boot-boun...@lists.denx.de] On
> Behalf Of "David Müller (ELSOFT AG)"
> Sent: Thursday, April 24, 2014 07:59
> To: u-boot@lists.denx.de
> Subject: [U-Boot] iMX6 PCie inbound traffic not working
>
> I tried to use a Intel 82574 based miniPCIe NIC on a
This mirrors the conventions used in other SPI drivers (kirkwood,
davinci, atmel, et al) where the din/dout buffer can be NULL when the
received/transmitted data isn't important. This reduces the need for
allocating additional buffers when write-only/read-only functionality is
needed.
In the din
78 matches
Mail list logo
