Re: [AFMUG] PMP 100 Sessions and Reg Counts

2017-11-11 Thread Forrest Christian (List Account) 
gr auto correct

On Nov 11, 2017 1:44 PM, "Forrest Christian (List Account)" <
li...@packetflux.com> wrote:

> if you have a storm SiteMonitor Base Unit attached to the injector,  we
> might be able to tell if the gps is in trouble.
>
> have you checked the log in the AP?
>
> On Nov 10, 2017 10:05 AM, "Jay Weekley"  wrote:
>
>> What do you think the problem here is?  We had to replace a PMP 100 900
>> MHz access point earlier in the week and now the Session and Reg counts
>> seem very high but there are no (zero) Re-Regs on any of the clients.  I
>> could blame it on interference or timing but the zero Re-Regs confuses me.
>> The AP uptime when I took this information was 26 hours and we're using
>> Packeflux timing.  We are also using a new Sync Injector but a used Sync
>> Pipe.
>>
>> LUID: 002 - [0a-00-3e-93-07-8c] State: IN SESSION (Encrypt Disabled)
>>   Site Name: , Darlene
>>   Software Version: CANOPY 12.1
>>   FPGA Version: 111010 (DES, Sched, US/ETSI) P10
>>   Session Timeout: 0, AirDelay: 70200 ns, 234 bits (approximately
>> 6.534 miles (34503 feet))
>>   Session Count: 295, Reg Count: 295, Re-Reg Count: 0, Session
>> Uptime: 02:41:03
>>
>> LUID: 003 - [0a-00-3e-93-61-03] State: IN SESSION (Encrypt Disabled)
>>   Site Name: , Scottie
>>   Software Version: CANOPY 12.1
>>   FPGA Version: 111010 (DES, Sched, US/ETSI) P10
>>   Session Timeout: 0, AirDelay: 3300 ns, 11 bits (approximately 0.307
>> miles (1621 feet))
>>   Session Count: 43, Reg Count: 43, Re-Reg Count: 0, Session Uptime:
>> 03:19:04
>>   Jitter (Avg/Last): 8/9   Power Level (Avg/Last): -56/-56
>>
>>   Rate: VC 19 Rate 2X/2X
>> LUID: 004 - [0a-00-3e-92-47-84] State: IN SESSION (Encrypt Disabled)
>>   Site Name: , Jeff
>>   Software Version: CANOPY 12.1
>>   FPGA Version: 101410 (DES, Sched, US/ETSI) P9
>>   Session Timeout: 0, AirDelay: 28500 ns, 95 bits (approximately
>> 2.652 miles (14007 feet))
>>   Session Count: 252, Reg Count: 252, Re-Reg Count: 0, Session
>> Uptime: 02:45:22
>>
>> LUID: 005 - [0a-00-3e-91-9f-9b] State: IN SESSION (Encrypt Disabled)
>>   Site Name: , Joseph
>>   Software Version: CANOPY 12.1
>>   FPGA Version: 101410 (DES, Sched, US/ETSI) P9
>>   Session Timeout: 0, AirDelay: 9300 ns, 31 bits (approximately 0.865
>> miles (4570 feet))
>>   Session Count: 41, Reg Count: 41, Re-Reg Count: 0, Session Uptime:
>> 03:18:41
>>
>> LUID: 006 - [0a-00-3e-93-08-16] State: IN SESSION (Encrypt Disabled)
>>   Site Name: , Steve
>>   Software Version: CANOPY 12.1
>>   FPGA Version: 111010 (DES, Sched, US/ETSI) P10
>>   Session Timeout: 0, AirDelay: 20100 ns, 67 bits (approximately
>> 1.871 miles (9879 feet))
>>   Session Count: 328, Reg Count: 328, Re-Reg Count: 0, Session
>> Uptime: 02:43:56
>>
>> LUID: 007 - [0a-00-3e-93-61-8d] State: IN SESSION (Encrypt Disabled)
>>   Site Name: , Ben
>>   Software Version: CANOPY 11.2
>>   FPGA Version: 111010 (DES, Sched, US/ETSI) P10
>>   Session Timeout: 0, AirDelay: 81900 ns, 273 bits (approximately
>> 7.623 miles (40253 feet))
>>   Session Count: 382, Reg Count: 382, Re-Reg Count: 0, Session
>> Uptime: 02:37:09
>>
>> LUID: 008 - [0a-00-3e-94-e5-39] State: IN SESSION (Encrypt Disabled)
>>   Site Name: , Regina
>>   Software Version: CANOPY 12.1
>>   FPGA Version: 111010 (DES, Sched, US/ETSI) P10
>>   Session Timeout: 0, AirDelay: 17100 ns, 57 bits (approximately
>> 1.591 miles (8404 feet))
>>   Session Count: 35, Reg Count: 35, Re-Reg Count: 0, Session Uptime:
>> 03:18:38
>>
>>
>

Re: [AFMUG] PMP 100 Sessions and Reg Counts

2017-11-11 Thread Forrest Christian (List Account) 
if you have a storm SiteMonitor Base Unit attached to the injector,  we
might be able to tell if the gps is in trouble.

have you checked the log in the AP?

On Nov 10, 2017 10:05 AM, "Jay Weekley"  wrote:

> What do you think the problem here is?  We had to replace a PMP 100 900
> MHz access point earlier in the week and now the Session and Reg counts
> seem very high but there are no (zero) Re-Regs on any of the clients.  I
> could blame it on interference or timing but the zero Re-Regs confuses me.
> The AP uptime when I took this information was 26 hours and we're using
> Packeflux timing.  We are also using a new Sync Injector but a used Sync
> Pipe.
>
> LUID: 002 - [0a-00-3e-93-07-8c] State: IN SESSION (Encrypt Disabled)
>   Site Name: , Darlene
>   Software Version: CANOPY 12.1
>   FPGA Version: 111010 (DES, Sched, US/ETSI) P10
>   Session Timeout: 0, AirDelay: 70200 ns, 234 bits (approximately
> 6.534 miles (34503 feet))
>   Session Count: 295, Reg Count: 295, Re-Reg Count: 0, Session
> Uptime: 02:41:03
>
> LUID: 003 - [0a-00-3e-93-61-03] State: IN SESSION (Encrypt Disabled)
>   Site Name: , Scottie
>   Software Version: CANOPY 12.1
>   FPGA Version: 111010 (DES, Sched, US/ETSI) P10
>   Session Timeout: 0, AirDelay: 3300 ns, 11 bits (approximately 0.307
> miles (1621 feet))
>   Session Count: 43, Reg Count: 43, Re-Reg Count: 0, Session Uptime:
> 03:19:04
>   Jitter (Avg/Last): 8/9   Power Level (Avg/Last): -56/-56
>
>   Rate: VC 19 Rate 2X/2X
> LUID: 004 - [0a-00-3e-92-47-84] State: IN SESSION (Encrypt Disabled)
>   Site Name: , Jeff
>   Software Version: CANOPY 12.1
>   FPGA Version: 101410 (DES, Sched, US/ETSI) P9
>   Session Timeout: 0, AirDelay: 28500 ns, 95 bits (approximately 2.652
> miles (14007 feet))
>   Session Count: 252, Reg Count: 252, Re-Reg Count: 0, Session
> Uptime: 02:45:22
>
> LUID: 005 - [0a-00-3e-91-9f-9b] State: IN SESSION (Encrypt Disabled)
>   Site Name: , Joseph
>   Software Version: CANOPY 12.1
>   FPGA Version: 101410 (DES, Sched, US/ETSI) P9
>   Session Timeout: 0, AirDelay: 9300 ns, 31 bits (approximately 0.865
> miles (4570 feet))
>   Session Count: 41, Reg Count: 41, Re-Reg Count: 0, Session Uptime:
> 03:18:41
>
> LUID: 006 - [0a-00-3e-93-08-16] State: IN SESSION (Encrypt Disabled)
>   Site Name: , Steve
>   Software Version: CANOPY 12.1
>   FPGA Version: 111010 (DES, Sched, US/ETSI) P10
>   Session Timeout: 0, AirDelay: 20100 ns, 67 bits (approximately 1.871
> miles (9879 feet))
>   Session Count: 328, Reg Count: 328, Re-Reg Count: 0, Session
> Uptime: 02:43:56
>
> LUID: 007 - [0a-00-3e-93-61-8d] State: IN SESSION (Encrypt Disabled)
>   Site Name: , Ben
>   Software Version: CANOPY 11.2
>   FPGA Version: 111010 (DES, Sched, US/ETSI) P10
>   Session Timeout: 0, AirDelay: 81900 ns, 273 bits (approximately
> 7.623 miles (40253 feet))
>   Session Count: 382, Reg Count: 382, Re-Reg Count: 0, Session
> Uptime: 02:37:09
>
> LUID: 008 - [0a-00-3e-94-e5-39] State: IN SESSION (Encrypt Disabled)
>   Site Name: , Regina
>   Software Version: CANOPY 12.1
>   FPGA Version: 111010 (DES, Sched, US/ETSI) P10
>   Session Timeout: 0, AirDelay: 17100 ns, 57 bits (approximately 1.591
> miles (8404 feet))
>   Session Count: 35, Reg Count: 35, Re-Reg Count: 0, Session Uptime:
> 03:18:38
>
>

Re: [AFMUG] PMP 100 Sessions and Reg Counts

2017-11-10 Thread CBB - Jay Fuller 

anytime i've seen this on our network it has been a sync issue

  - Original Message - 
  From: Jay Weekley 
  To: af@afmug.com 
  Sent: Friday, November 10, 2017 11:05 AM
  Subject: [AFMUG] PMP 100 Sessions and Reg Counts


  What do you think the problem here is?  We had to replace a PMP 100 900 MHz 
access point earlier in the week and now the Session and Reg counts seem very 
high but there are no (zero) Re-Regs on any of the clients.  I could blame it 
on interference or timing but the zero Re-Regs confuses me.  The AP uptime when 
I took this information was 26 hours and we're using Packeflux timing.  We are 
also using a new Sync Injector but a used Sync Pipe. 

  LUID: 002 - [0a-00-3e-93-07-8c] State: IN SESSION (Encrypt Disabled)
Site Name: , Darlene
Software Version: CANOPY 12.1
FPGA Version: 111010 (DES, Sched, US/ETSI) P10
Session Timeout: 0, AirDelay: 70200 ns, 234 bits (approximately 6.534 
miles (34503 feet))
Session Count: 295, Reg Count: 295, Re-Reg Count: 0, Session Uptime: 
02:41:03

  LUID: 003 - [0a-00-3e-93-61-03] State: IN SESSION (Encrypt Disabled)
Site Name: , Scottie
Software Version: CANOPY 12.1
FPGA Version: 111010 (DES, Sched, US/ETSI) P10
Session Timeout: 0, AirDelay: 3300 ns, 11 bits (approximately 0.307 
miles (1621 feet))
Session Count: 43, Reg Count: 43, Re-Reg Count: 0, Session Uptime: 
03:19:04
Jitter (Avg/Last): 8/9   Power Level (Avg/Last): -56/-56
  
Rate: VC 19 Rate 2X/2X   
  LUID: 004 - [0a-00-3e-92-47-84] State: IN SESSION (Encrypt Disabled)
Site Name: , Jeff
Software Version: CANOPY 12.1
FPGA Version: 101410 (DES, Sched, US/ETSI) P9
Session Timeout: 0, AirDelay: 28500 ns, 95 bits (approximately 2.652 
miles (14007 feet))
Session Count: 252, Reg Count: 252, Re-Reg Count: 0, Session Uptime: 
02:45:22

  LUID: 005 - [0a-00-3e-91-9f-9b] State: IN SESSION (Encrypt Disabled)
Site Name: , Joseph 
Software Version: CANOPY 12.1
FPGA Version: 101410 (DES, Sched, US/ETSI) P9
Session Timeout: 0, AirDelay: 9300 ns, 31 bits (approximately 0.865 
miles (4570 feet))
Session Count: 41, Reg Count: 41, Re-Reg Count: 0, Session Uptime: 
03:18:41
 
  LUID: 006 - [0a-00-3e-93-08-16] State: IN SESSION (Encrypt Disabled)
Site Name: , Steve 
Software Version: CANOPY 12.1
FPGA Version: 111010 (DES, Sched, US/ETSI) P10
Session Timeout: 0, AirDelay: 20100 ns, 67 bits (approximately 1.871 
miles (9879 feet))
Session Count: 328, Reg Count: 328, Re-Reg Count: 0, Session Uptime: 
02:43:56

  LUID: 007 - [0a-00-3e-93-61-8d] State: IN SESSION (Encrypt Disabled)
Site Name: , Ben
Software Version: CANOPY 11.2
FPGA Version: 111010 (DES, Sched, US/ETSI) P10
Session Timeout: 0, AirDelay: 81900 ns, 273 bits (approximately 7.623 
miles (40253 feet))
Session Count: 382, Reg Count: 382, Re-Reg Count: 0, Session Uptime: 
02:37:09

  LUID: 008 - [0a-00-3e-94-e5-39] State: IN SESSION (Encrypt Disabled)
Site Name: , Regina 
Software Version: CANOPY 12.1
FPGA Version: 111010 (DES, Sched, US/ETSI) P10
Session Timeout: 0, AirDelay: 17100 ns, 57 bits (approximately 1.591 
miles (8404 feet))
Session Count: 35, Reg Count: 35, Re-Reg Count: 0, Session Uptime: 
03:18:38

Re: [AFMUG] PMP 100 Sessions and Reg Counts

2017-11-10 Thread Tyson Burris 
IF you have this many subs with issues, you have a faulty AP or water in the 
connector, or a GPS issue.
That’s been my experience when the entire AP VC’s shows rereg issues.

Regardless, try moving to the last FW released to be safe or change channels.



Tyson Burris, President
Internet Communications Inc.
739 Commerce Dr.
Franklin, IN 46131

Daytime # 317-738-0320
Cell/Direct # 317-412-1540
Online: www.surfici.net

[ICI]
What can ICI do for you?

Broadband Wireless - PtP/PtMP Solutions - WiMax - Mesh Wifi/Hotzones - IP 
Security - Fiber - Tower - Infrastructure.

CONFIDENTIALITY NOTICE: This e-mail is intended for the
addressee shown. It contains information that is
confidential and protected from disclosure. Any review,
dissemination or use of this transmission or its contents by
unauthorized organizations or individuals is strictly
prohibited.

From: Af [mailto:af-boun...@afmug.com] On Behalf Of George Skorup
Sent: Friday, November 10, 2017 12:45 PM
To: af@afmug.com
Subject: Re: [AFMUG] PMP 100 Sessions and Reg Counts

Are you seriously still running 11.2 or 12.1? What version is the AP on? There 
was a timing bug for a very long time that was fixed with the final 13.4.1 
release. There *is* a difference between power port and timing port sync prior 
to 13.4.1.

The difference between a reg and a re-reg is very simple. A reg is when the 
session is new or idle. A re-reg means the AP hasn't torn down that session, 
but sees a registration attempt. That's often the case when the VC isn't very 
active, so the AP just kinda assumes it's still there. Or the SM doesn't see 
enough beacons and assumes it's out of session. Bursty interference, 
multi-path, etc.

Also, what h/w is the AP? P9's didn't have the best RF performance and 
calibration could be an issue. Been through that a dozen times. As we pull down 
900 APs, any P9's get compared to a known-good P9 and a P10 AP using 60dB pad. 
If the uplink and downlink power and jitter levels aren't sane, they go right 
in the recycle bin.
On 11/10/2017 11:05 AM, Jay Weekley wrote:
What do you think the problem here is?  We had to replace a PMP 100 900 MHz 
access point earlier in the week and now the Session and Reg counts seem very 
high but there are no (zero) Re-Regs on any of the clients.  I could blame it 
on interference or timing but the zero Re-Regs confuses me.  The AP uptime when 
I took this information was 26 hours and we're using Packeflux timing.  We are 
also using a new Sync Injector but a used Sync Pipe.

LUID: 002 - [0a-00-3e-93-07-8c] State: IN SESSION (Encrypt Disabled)
  Site Name: , Darlene
  Software Version: CANOPY 12.1
  FPGA Version: 111010 (DES, Sched, US/ETSI) P10
  Session Timeout: 0, AirDelay: 70200 ns, 234 bits (approximately 6.534 
miles (34503 feet))
  Session Count: 295, Reg Count: 295, Re-Reg Count: 0, Session Uptime: 
02:41:03

LUID: 003 - [0a-00-3e-93-61-03] State: IN SESSION (Encrypt Disabled)
  Site Name: , Scottie
  Software Version: CANOPY 12.1
  FPGA Version: 111010 (DES, Sched, US/ETSI) P10
  Session Timeout: 0, AirDelay: 3300 ns, 11 bits (approximately 0.307 miles 
(1621 feet))
  Session Count: 43, Reg Count: 43, Re-Reg Count: 0, Session Uptime: 
03:19:04
  Jitter (Avg/Last): 8/9   Power Level (Avg/Last): -56/-56

  Rate: VC 19 Rate 2X/2X
LUID: 004 - [0a-00-3e-92-47-84] State: IN SESSION (Encrypt Disabled)
  Site Name: , Jeff
  Software Version: CANOPY 12.1
  FPGA Version: 101410 (DES, Sched, US/ETSI) P9
  Session Timeout: 0, AirDelay: 28500 ns, 95 bits (approximately 2.652 
miles (14007 feet))
  Session Count: 252, Reg Count: 252, Re-Reg Count: 0, Session Uptime: 
02:45:22

LUID: 005 - [0a-00-3e-91-9f-9b] State: IN SESSION (Encrypt Disabled)
  Site Name: , Joseph
  Software Version: CANOPY 12.1
  FPGA Version: 101410 (DES, Sched, US/ETSI) P9
  Session Timeout: 0, AirDelay: 9300 ns, 31 bits (approximately 0.865 miles 
(4570 feet))
  Session Count: 41, Reg Count: 41, Re-Reg Count: 0, Session Uptime: 
03:18:41

LUID: 006 - [0a-00-3e-93-08-16] State: IN SESSION (Encrypt Disabled)
  Site Name: , Steve
  Software Version: CANOPY 12.1
  FPGA Version: 111010 (DES, Sched, US/ETSI) P10
  Session Timeout: 0, AirDelay: 20100 ns, 67 bits (approximately 1.871 
miles (9879 feet))
  Session Count: 328, Reg Count: 328, Re-Reg Count: 0, Session Uptime: 
02:43:56

LUID: 007 - [0a-00-3e-93-61-8d] State: IN SESSION (Encrypt Disabled)
  Site Name: , Ben
  Software Version: CANOPY 11.2
  FPGA Version: 111010 (DES, Sched, US/ETSI) P10
  Session Timeout: 0, AirDelay: 81900 ns, 273 bits (approximately 7.623 
miles (40253 feet))
  Session Count: 382, Reg Count: 382, Re-Reg Count: 0, Session Uptime: 
02:37:09

LUID: 008 - [0a-00-3e-94-e5-39] State: IN SESSION (Encrypt Disabled)
  Site Name: , Regina
  Software Version: CANOPY 12.1
  FPGA Version: 111010 (DES, Sched, US/ETSI) P10
  Session Timeout: 0

Re: [AFMUG] PMP 100 Sessions and Reg Counts

2017-11-10 Thread George Skorup 
Are you seriously still running 11.2 or 12.1? What version is the AP on? 
There was a timing bug for a very long time that was fixed with the 
final 13.4.1 release. There *is* a difference between power port and 
timing port sync prior to 13.4.1.


The difference between a reg and a re-reg is very simple. A reg is when 
the session is new or idle. A re-reg means the AP hasn't torn down that 
session, but sees a registration attempt. That's often the case when the 
VC isn't very active, so the AP just kinda assumes it's still there. Or 
the SM doesn't see enough beacons and assumes it's out of session. 
Bursty interference, multi-path, etc.


Also, what h/w is the AP? P9's didn't have the best RF performance and 
calibration could be an issue. Been through that a dozen times. As we 
pull down 900 APs, any P9's get compared to a known-good P9 and a P10 AP 
using 60dB pad. If the uplink and downlink power and jitter levels 
aren't sane, they go right in the recycle bin.


On 11/10/2017 11:05 AM, Jay Weekley wrote:
What do you think the problem here is?  We had to replace a PMP 100 
900 MHz access point earlier in the week and now the Session and Reg 
counts seem very high but there are no (zero) Re-Regs on any of the 
clients.  I could blame it on interference or timing but the zero 
Re-Regs confuses me.  The AP uptime when I took this information was 
26 hours and we're using Packeflux timing.  We are also using a new 
Sync Injector but a used Sync Pipe.


LUID: 002 - [0a-00-3e-93-07-8c] State: IN SESSION (Encrypt Disabled)
  Site Name: , Darlene
  Software Version: CANOPY 12.1
  FPGA Version: 111010 (DES, Sched, US/ETSI) P10
  Session Timeout: 0, AirDelay: 70200 ns, 234 bits (approximately 
6.534 miles (34503 feet))
Session Count: 295, Reg Count: 295, Re-Reg Count: 0, Session Uptime: 
02:41:03


LUID: 003 - [0a-00-3e-93-61-03] State: IN SESSION (Encrypt Disabled)
  Site Name: , Scottie
  Software Version: CANOPY 12.1
  FPGA Version: 111010 (DES, Sched, US/ETSI) P10
  Session Timeout: 0, AirDelay: 3300 ns, 11 bits (approximately 
0.307 miles (1621 feet))
Session Count: 43, Reg Count: 43, Re-Reg Count: 0, Session Uptime: 
03:19:04

  Jitter (Avg/Last): 8/9   Power Level (Avg/Last): -56/-56

  Rate: VC 19 Rate 2X/2X
LUID: 004 - [0a-00-3e-92-47-84] State: IN SESSION (Encrypt Disabled)
  Site Name: , Jeff
  Software Version: CANOPY 12.1
  FPGA Version: 101410 (DES, Sched, US/ETSI) P9
  Session Timeout: 0, AirDelay: 28500 ns, 95 bits (approximately 
2.652 miles (14007 feet))
Session Count: 252, Reg Count: 252, Re-Reg Count: 0, Session Uptime: 
02:45:22


LUID: 005 - [0a-00-3e-91-9f-9b] State: IN SESSION (Encrypt Disabled)
  Site Name: , Joseph
  Software Version: CANOPY 12.1
  FPGA Version: 101410 (DES, Sched, US/ETSI) P9
  Session Timeout: 0, AirDelay: 9300 ns, 31 bits (approximately 
0.865 miles (4570 feet))
Session Count: 41, Reg Count: 41, Re-Reg Count: 0, Session Uptime: 
03:18:41


LUID: 006 - [0a-00-3e-93-08-16] State: IN SESSION (Encrypt Disabled)
  Site Name: , Steve
  Software Version: CANOPY 12.1
  FPGA Version: 111010 (DES, Sched, US/ETSI) P10
  Session Timeout: 0, AirDelay: 20100 ns, 67 bits (approximately 
1.871 miles (9879 feet))
Session Count: 328, Reg Count: 328, Re-Reg Count: 0, Session Uptime: 
02:43:56


LUID: 007 - [0a-00-3e-93-61-8d] State: IN SESSION (Encrypt Disabled)
  Site Name: , Ben
  Software Version: CANOPY 11.2
  FPGA Version: 111010 (DES, Sched, US/ETSI) P10
  Session Timeout: 0, AirDelay: 81900 ns, 273 bits (approximately 
7.623 miles (40253 feet))
  Session Count: 382, Reg Count: 382, Re-Reg Count: 0, Session Uptime: 
02:37:09


LUID: 008 - [0a-00-3e-94-e5-39] State: IN SESSION (Encrypt Disabled)
  Site Name: , Regina
  Software Version: CANOPY 12.1
  FPGA Version: 111010 (DES, Sched, US/ETSI) P10
  Session Timeout: 0, AirDelay: 17100 ns, 57 bits (approximately 
1.591 miles (8404 feet))
Session Count: 35, Reg Count: 35, Re-Reg Count: 0, Session Uptime: 
03:18:38

[AFMUG] PMP 100 Sessions and Reg Counts

2017-11-10 Thread Jay Weekley 

  
  
What do you think the problem here is?  We had to replace a PMP 100
900 MHz access point earlier in the week and now the Session and Reg
counts seem very high but there are no (zero) Re-Regs on any of the
clients.  I could blame it on interference or timing but the zero
Re-Regs confuses me.  The AP uptime when I took this information was
26 hours and we're using Packeflux timing.  We are also using a new
Sync Injector but a used Sync Pipe. 

LUID: 002 - [0a-00-3e-93-07-8c] State: IN SESSION (Encrypt Disabled)
  Site Name: , Darlene
  Software Version: CANOPY 12.1
  FPGA Version: 111010 (DES, Sched, US/ETSI) P10
  Session Timeout: 0, AirDelay: 70200 ns, 234 bits
(approximately 6.534 miles (34503 feet))
  Session Count: 295, Reg Count: 295,
  Re-Reg Count: 0, Session Uptime: 02:41:03
  
LUID: 003 - [0a-00-3e-93-61-03] State: IN SESSION (Encrypt Disabled)
  Site Name: , Scottie
  Software Version: CANOPY 12.1
  FPGA Version: 111010 (DES, Sched, US/ETSI) P10
  Session Timeout: 0, AirDelay: 3300 ns, 11 bits (approximately
0.307 miles (1621 feet))
  Session Count: 43, Reg Count: 43, Re-Reg
  Count: 0, Session Uptime: 03:19:04
  Jitter (Avg/Last): 8/9   Power Level (Avg/Last): -56/-56
    
  Rate: VC 19 Rate 2X/2X   
LUID: 004 - [0a-00-3e-92-47-84] State: IN SESSION (Encrypt Disabled)
  Site Name: , Jeff
  Software Version: CANOPY 12.1
  FPGA Version: 101410 (DES, Sched, US/ETSI) P9
  Session Timeout: 0, AirDelay: 28500 ns, 95 bits (approximately
2.652 miles (14007 feet))
  Session Count: 252, Reg Count: 252,
  Re-Reg Count: 0, Session Uptime: 02:45:22
  
LUID: 005 - [0a-00-3e-91-9f-9b] State: IN SESSION (Encrypt Disabled)
  Site Name: , Joseph 
  Software Version: CANOPY 12.1
  FPGA Version: 101410 (DES, Sched, US/ETSI) P9
  Session Timeout: 0, AirDelay: 9300 ns, 31 bits (approximately
0.865 miles (4570 feet))
  Session Count: 41, Reg Count: 41, Re-Reg
  Count: 0, Session Uptime: 03:18:41
   
LUID: 006 - [0a-00-3e-93-08-16] State: IN SESSION (Encrypt Disabled)
  Site Name: , Steve 
  Software Version: CANOPY 12.1
  FPGA Version: 111010 (DES, Sched, US/ETSI) P10
  Session Timeout: 0, AirDelay: 20100 ns, 67 bits (approximately
1.871 miles (9879 feet))
  Session Count: 328, Reg Count: 328,
  Re-Reg Count: 0, Session Uptime: 02:43:56
  
LUID: 007 - [0a-00-3e-93-61-8d] State: IN SESSION (Encrypt Disabled)
  Site Name: , Ben
  Software Version: CANOPY 11.2
  FPGA Version: 111010 (DES, Sched, US/ETSI) P10
  Session Timeout: 0, AirDelay: 81900 ns, 273 bits
(approximately 7.623 miles (40253 feet))
  Session Count: 382, Reg Count: 382,
  Re-Reg Count: 0, Session Uptime: 02:37:09
  
LUID: 008 - [0a-00-3e-94-e5-39] State: IN SESSION (Encrypt Disabled)
  Site Name: , Regina 
  Software Version: CANOPY 12.1
  FPGA Version: 111010 (DES, Sched, US/ETSI) P10
  Session Timeout: 0, AirDelay: 17100 ns, 57 bits (approximately
1.591 miles (8404 feet))
  Session Count: 35, Reg Count: 35,
  Re-Reg Count: 0, Session Uptime: 03:18:38