[Asterisk-Users] codec selection based on call prefix
Hi all, I have an IAX connection between two asterisk servers and i'm looking for a way to cut down on the needed bandwidth. Both voice and fax calls pass through the channel so it is currently configured to use g.711. Could it be possible to select the codec based on the call's prefix so that g.711 will be used for fax calls and g.729 for voice? Dionisis ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
[Asterisk-Users] multiple line registrations on attendant console
Hi all, I've noticed that Polycom and Snom each offer attendant console expansions. As far as I understand, the point in using all the buttons they provide is to program them to register as extensions in order to be able to monitor the status of each extension at any given time and, also, to be able to pickup any extension that has been ringing for a while. Is this feature supported by asterisk? I have tried to register two sip phones with the same extension but when I dial the extension only one of the phones rings. This is a feature that is necessary in many telephony environments and I'd be happy to be able to implement it using asterisk. I've searched through the list's posts for the past few months but didn't come up with anything usefull. any help would be greatly appreciated Dionisis ___ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
[Asterisk-Users] wctdm module won't load after kernel upgrade
Hi all, I have installed a TDM22B on an IBM xSeries 220 with FedoraCore 3 and setup asterisk cvs head to work properly. A few days ago, I tried to update the system kernel to 2.6.12 from 2.6.9 and also to change to asterisk stable 1.0.9. After compiling zaptel and asterisk, i loaded zaptel and tried to load the wctdm module but this failed with the following message: Notice: Configuration file is /etc/zaptel.conf line 206: Unable to open master device '/dev/zap/ctl' I checked /dev/ and there is no /zap directory but, instead, some devices that look relevant like zap1, zap2 etc. Obviously, if boot with the older kernel, wctdm will not load either. Any help is welcome Thanks in advance, dionisis ___ --Bandwidth and Colocation sponsored by Easynews.com -- Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
[Asterisk-Users] Fw: linksys rt31p2 test case
yes, I'm pinging the routers from the same vlan. Dionisis KoumourasS/W EngineerCyberStream Ltd.tel. +30 210 729 7632fax. +30 210 729 7631mob. +30 694 7301104 ___ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
[Asterisk-Users] Fw: linksys rt31p2 test case
Hi all, I'm trying to set up a test case for an ISP featuring an asterisk server and a couple of linksys rt31p2-na routers registering on it. Instead of using dsl lines, i'm trying to plug the * server and the routers on a cisco switch, just to test their functionality. I have created a vlan and a subnet on the switch and set up the ip addresses of the routers in that subnet. When i plug the routers in the switch through their internet port, i cannot even ping them. Is this normal behaviour? Are these routers only supposed to work with a dsl/cable modem attached to that "internet" port? I'm sure that i have not miscofigured the switch since i had a cisco expert take care of that. thx in advance, Dionisis ___ Asterisk-Users mailing list Asterisk-Users@lists.digium.com http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users